BLOG PAGES

Wednesday, August 30, 2023

CGE CT 8826 TV 26" TELECOLOR (TELEFUNKEN) YEAR 1978


 
 
 The CGE CT8826 TV26" TELECOLOR  is A 26 inches color television with infra red remote and 16 programs preselection.
 
  • A 16 red led display shows program number.
  • Tuning search system with Tuning Bar display system of led lamps in the searching box.

This set is very similar to the TELEFUNKEN PALCOLOR 6868  YEAR 1978


It's marketed & sold under the Italian brand CGE (see further on this page) but is indeed a TELEFUNKEN Palcolor completely in every part !

  • The set feaures dynamic focusing:

 In any television picture tube the beam length is relatively longer at the edges of the screen than at the centre. Thus the sharpness of the picture at the edges is much worse than at the centre. The effect is barely noticeable with a 90° c.r.t., but is much more noticeable with a 110° c.r.t. used with the conventional focusing arrangement.
To overcome this effect a few of the more sophisticated receivers, such as this Telefunken chassis, employ a dynamic focusing circuit which automatically compensates for the loss of sharpness at the edges of the screen by varying the focus voltage in proportion to beam length. This is done by superimposing an additional parabolic voltage waveform, at line frequency, on to the conventionally derived focus voltage.


  • This is the First CGE TELEFUNKEN with the introduction of the 20AX TUBE (PHILIPS TECHNOLOGY) WITH THE TELEFUNKEN CHASSIS 712A and first model series with SMPS POWER SUPPLY with Mains isolated chassis and remote controller with infra red trasmission technology instead of ultrasonic transmitter system.The PHILIPS 20AX system was introduced in Europe as the first self converging picture tube/deflection coil, combination for 110° degree deflection and screen sizes up to 26". The system is based on the automatic convergence principle discovered by Haantjes and Lubben of Philips Research Laboratory more than 20 years ago. It makes use of an in-line gun array in conjunction with a specially designed saddle type deflection coil. Residual small tolerance errors are compensated by a simple dynamic four-pole system. The tube is 2 cm shorter than conventional 110° Degree tubes and has a standard 36.5 mm neck in order to obtain good color selection. A slotted mask is used in combination with a stripe-structure screen. Picture sharpness is ensured by an astigmatic electron gun.
  •  Featuring a Switch mode Power supply combined with isolated ground chassis from mains.
Television receivers, which obtain operating power from an alternating current source producing any one of a plurality of RMS potentials within a predetermined range, have, traditionally, been provided with various regulation circuits in order to maintain relatively uniform performance of the television receiver within the predetermined range of RMS potentials. This type of circuit provides good regulation of all operating direct current potentials within the range of RMS potentials as well as isolation between the source of alternating current and the television receiver chassis. Switch mode power supply means, especially for a television receiver, having a working winding , a switching transistor , a back-coupling winding  and a control switch  on the primary side of a divided transformer, and also having rectifiers  for the production of the drive voltages (U1, U2, U3) on the secondary side of the transformer , characterized by the following features :  Connected to a winding  there is a thyristor  which is poled in the permitted direction for the voltage at the winding  arising during the current conducting phase of the switching transistor.  One of the drive voltages  is applied to the control electrode of the thyristor  with such magnitude that the thyristor  remains blocked in the normal working state and fires on the occurrence of an inadmissible rise of the drive voltage.

  • In this model was present sound tone control (Klang regler) and headphone DIN jack connector.

  • The tuning is performed via sequential electronic search manually AFC driven and with led lamps indicating tuning sequencing.
The tuning system also includes an automatic fine tuning (AFT) frequency discriminator for tuning the local oscillator to minimize any deviation between the frequency of an actual picture carrier and the nominal picture carrier frequency. If the receiver is coupled to a television distribution system which provides RF carriers having nonstandard frequencies arbitrarily near respective ones of the standard broadcast frequencies, when the phase locked loop has achieved lock at a nominal frequency, a mode control unit selectively couples the discriminator and a frequency drift control circuit to the local oscillator.

The general concept of Automatic Frequency Control (AFC) for television receivers is known in the art and has been adapted to radio receivers as well as to television receivers of both the monochrome and color variety. The general purpose of such a system is to assist the user in attaining proper fine-tuning of the receiver without requiring critical manual adjustment. The advantage of such a system is self-evident but its value to a color receiver is markedly increased due to the fact that improper tuning of a color receiver manifests itself in incorrect colors, or even a total lack of color, in the reproduced image. Typically, the AFC system is tuned to a reference or center frequency corresponding to the desired video IF frequency and so long as the tuning is reasonably close, within the response of the AFC system, an error voltage is developed to correct the tuning. If the user of the television receiver makes the fine-tuning adjustment while the AFC system is operative, he may adjust it to a point where the picture is acceptable but a substantial amount of AFC correction voltage is required. Thus, the receiver may be tuned at the limit of the "hold-in" range and would not give the proper "pull-in" performance when the channel selector is switched to the next channel. Accordingly, it is desirable to include an AFC defeat circuit for disabling the AFC system during manual fine-tuning. Heretofore, most AFC defeat circuits have required that the user of the television receiver defeat the AFC system by means of a manual switch. It is apparent, however, that the typical user of a television receiver may at times forget to flip the switch and hence the attendant problems are realized.
The CRT tube is anyway a TELEFUNKEN in 26" sets but in 22" they were used to be PHILIPS.

  • The set is build with a Modular chassis design because as modern television receivers become more complex the problem of repairing the receiver becomes more difficult. As the number of components used in the television receiver increases the susceptibility to breakdown increases and it becomes more difficult to replace defective components as they are more closely spaced. The problem has become even more complicated with the increasing number of color television receivers in use. A color television receiver has a larger number of circuits of a higher degree of complexity than the black and white receiver and further a more highly trained serviceman is required to properly service the color television receiver.
Fortunately for the service problem to date, most failures occur in the vacuum tubes used in the television receivers. A faulty or inoperative vacuum tube is relatively easy to find and replace. However, where the television receiver malfunction is caused by the failure of other components, such as resistors, capacitors or inductors, it is harder to isolate the defective component and a higher degree of skill on the part of the serviceman is required.
Even with the great majority of the color television receiver malfunctions being of the "easy to find and repair" type proper servicing of color sets has been difficult to obtain due to the shortage of trained serviceman.
At the present time advances in the state of the semiconductor art have led to the increasing use of transistors in color television receivers. The receiver described in this application has only two tubes, the picture tube and the high voltage rectifier tube, all the other active components in the receiver being semiconductors.
One important characteristic of a semiconductor device is its extreme reliability in comparison with the vacuum tube. The number of transistor and integrated circuit failures in the television receiver will be very low in comparison with the failures of other components, the reverse of what is true in present day color television receivers. Thus most failures in future television receivers will be of the hard to service type and will require more highly qualified servicemen.
The primary symptoms of a television receiver malfunction are shown on the picture tube of the television receiver while the components causing the malfunction are located within the cabinet. Also many adjustments to the receiver require the serviceman to observe the screen. Thus the serviceman must use unsatisfactory mirror arrangements to remove the electronic chassis from the cabinet, usually a very difficult task. Further many components are "buried" in a maze of circuitry and other components so that they are difficult to remove and replace without damage to other components in the receiver.
Repairing a modern color television receiver often requires that the receiver be removed from the home and carried to a repair shop where it may remain for many weeks. This is an expensive undertaking since most receivers are bulky and heavy enough to require at least two persons to carry them. Further, two trips must be made to the home, one to pick up the receiver and one to deliver it. For these reasons, the cost of maintaining the color television receiver in operating condition often exceeds the initial cost of the receiver and is an important factor in determining whether a receiver will be purchased.
Therefore, the object of this invention is to provide a transistorized color television receiver in which the main electronic chassis is easily accessible for maintenance and adjustment. Another object of this invention is to provide a transistorized color television receiver in which the electronic circuits are divided into a plurality of modules with the modules easily removable for service and maintenance. The main electronic chassis is slidably mounted within the cabinet so that it may be withdrawn, in the same manner as a drawer, to expose the electronic circuitry therein for maintenance and adjustment from the rear closure panel after easy removal. Another aspect is the capability to be serviced at eventually the home of the owner.
(Almost needless to say that the set is fully functional with superb pictures)


A LOOK TO THE FUTURE:
Dr. Walter Bruch of Telefunken inventor of the PAL colour system, speaking to the Royal Television Society in London in 1972 has predicted the end of monochrome television after 1980. Dr. Bruch believes that in ten years' time colour will have taken over completely. Like many others Dr. Bruch does not see an early end to the shadowmask tube and believes it will be 20-30 years before a flat solid-state display device will be a practical alternative. Dr. Bruch predicts that most TV set circuitry will be packed into a couple of i.c.s well before then.

----------------------------------------------------------

  • The Compagnia Generale di Elettricità is General Electric Power Company, more famous with the Cge acronym, was an Italian joint-stock company electrical engineering and electronics manufacturer.

History

It was founded in 1921 to Milan like Italian division of the industrial group American General Electric. The activity of the society initially was oriented to the commercialization of receiving apparatuses of the RCA (radios) .

Towards the end of years twenty it began to always become producing of wireless apparatuses. The company grew quickly, and in the '30 it was placed between first place at a national level in production of radios. Remarkable happening collected models like Audioletta, Consoletta and Radio Balilla.

The production came widened also to the radiophonographs, amplifiers, loudspeakers, caps and systems of recording and reproduction. In the same period one specialized also in the production of other types of apparatuses electrical workers like dynamo, transformers and motors.

It was introduced in the field of the transports because for many years it supplied the equipment for the powertrain technology components machinery.

In 1941 the Cge acquired FAR (former SAFAR), created the FIAR (Italian Factory Apparatuses Radios) and two plants, to Milan and Baranzate.

The first one was used for the realization of a series of apparatuses radios and navigation, and the relative necessary components to the equipment fabrication radios electrical workers. The second instead was used for the normal production of wireless apparatuses. In the years after the Second World War resumptions the production activity, IT has extended to the household-electric appliances and televisions.

For how much it concerns this last field, great part of the production came moved in 1946 in the plant of Baranzate, that Italian Factory Radio and Televisori came renamed FIRT (). In 1958 it acquired the brand of the failed company manufacturer of wireless apparatuses Unda radio.

With the Unda brand it produced radio receivers till 1962. In 1950 in plant FIAR of Milan, the Cge was specialized in the construction of transmitter-receivers for army, while from 1961 it started the realization of radar for naval activity and aeronautics . FIAR came then joined to the Cge in 1967 [1]. In 1966, the electrotechnical production of the Cge met in Ansaldo-Saint George.

In the field of consumer electronics the Cge remained active in the successive years till 1994, when it stopped definitively the activity (AKA DEAD).



Telefunken (WAS) is a German radio and television apparatus company, founded in 1903, in Berlin, as a joint venture of two large companies, Siemens & Halske (S & H) and the Allgemeine Elektricitäts-Gesellschaft (General Electricity Company).

The name "Telefunken" appears in:

* the product brand name "Telefunken";
* AEG subsidiary as Telefunken GmbH in 1955;
* AEG subsidiary as Telefunken AG in 1963;
* company merged as AEG-Telefunken (1967–1985);
* the company "Telefunken USA" (2001). Now Telefunken Elektroakustik (2009)
* the company "Telefunken semiconductor GmbH & Co KG" Heilbronn Germany (2009).
* the company "Telefunken Lighting technologies S,L" (2009)

The company Telefunken USA[1] was incorporated in early 2001 to provide restoration services and build reproductions of vintage Telefunken microphones.

Around the turn of the 20th century, two groups of German researchers worked on the development of techniques for wireless communication. The one group at AEG, led by Adolf Slaby and Georg Graf von Arco, developed systems for the German navy; the other one, under Karl Ferdinand Braun, at Siemens, for the German army.

When a dispute concerning patents arose between the two companies, Kaiser Wilhelm II decided that the two companies were to be joined, creating on 27 May 1903 the company Gesellschaft für drahtlose Telegraphie System Telefunken ("The Company for Wireless Telegraphy Ltd."), and the disputed patents and techniques were invested in it. This was then renamed on 17 April 1923 as Telefunken, The Company for Wireless Telegraphy. Telefunken was the company's telegraph address. The first technical director of Telefunken was George Graf von Arco.

Starting in 1923, Telefunken built broadcast transmitters and radio sets.

In 1928, Telefunken made history by designing the V-41 amplifier for the German Radio Network. This was the very first two stage, "Hi-Fi" amplifier which began a chapter in recording history. Over time, Telefunken perfected their designs and in 1950 the V-72 amplifier was born. The TAB (a manufacturing subcontractor to Telefunken) V-72 soon became popular with other radio stations and recording facilities and would eventually come to help define the sound of most European recordings. The V-72S was the only type of amplifier found in the legendary REDD-37 console used by the Beatles at Abbey Road Studios on every recording prior to Rubber Soul. Today the V-72 is still the most sought after example of Telefunken's design and over 50 years later continues to be the benchmark by which all other tube based microphone preamplifiers are measured. In 1932, record players were added to the product line.

In 1941 Siemens transferred its Telefunken shares to AEG as part of the agreements known as the "Telefunken settlement", and AEG thus became the sole owner and continued to lead Telefunken as a subsidiary (starting in 1955 as "Telefunken GmbH" and from 1963 as "Telefunken AG").

During the Second World War Telefunken was a supplier of vacuum tubes, transmitters and radio relay systems, and developed radar facilities and directional finders, aiding extensively to the German air defense against British-American Aerial Bombing. During the war, manufacturing plants were shifted to and developed in West Germany or relocated. Thus, Telefunken, under AEG, turned into the smaller subsidiary, with the three divisions realigning and data processing technology, elements as well as broadcast, television and phono. Telefunken had substantial successes in these markets during the time of self-sufficiency and also later in the AEG company. Telefunken was also the originator of the FM radio broadcast system. Telefunken, through the subsidiary company Teldec (a joint venture with Decca Records), was for many decades one of the largest German record companies, until Teldec was sold to WEA in 1988.

In 1959, Telefunken established a modern semiconductor works in Heilbronn, where in April 1960 production began. The works was expanded several times, and in 1970 a new 6-storey building was built at the northern edge of the area. At the beginning of the 1970s it housed approximately 2,500 employees.

In 1967, Telefunken was merged with AEG, which was then renamed to AEG-Telefunken. During this era, Walter Bruch developed the PAL color television for the company, in use by most countries outside the Americas today (i.e. United Kingdom - PAL-I), and by Brazil (PAL-M) and Argentina (PAL-N) in South America.

The mainframe computer TR 4 was developed at Telefunken in Backnang, and the TR 440 model was developed at Telefunken in Konstanz. They were in use at many German university computing centres from the 1970s to around 1985. The development and manufacture of large computers was separated in 1974 to the Konstanz Computer Company (CGK). The production of mini- and process computers was integrated into the automatic control engineering division of AEG. When AEG was bought by Daimler in 1985, "Telefunken" was dropped from the company name.

In 2005, Telefunken Sender Systeme Berlin changed its name to Transradio SenderSysteme Berlin AG. The name "Transradio" dates back to 1918, when Transradio was founded as a subsidiary of Telefunken. A year later, in 1919, Transradio made history by introducing duplex transmission. Transradio has specialized in research, development and design of modern AM, VHF/FM and DRM broadcasting systems.

In August 2006, it acquired the Turkish company Profilo Telra, one of the largest European manufacturers of TV-devices, with Telefunken GmbH granting a license for the Telefunken trademark rights and producing televisions under that name. In 2000, Toni Roger Fishman acquired The Diamond Shaped Logo & The Telefunken Brand Name for use in North America. The company "Telefunken USA" [2] was incorporated in early 2001 to provide restoration services and build reproductions of vintage Telefunken microphones. In 2003, Telefunken USA won a TEC Award for Studio Microphone Technology for their exact reproduction of the original Ela M 250 / 251 Microphone system. Telefunken USA has since received several TEC Awards nominations for the following microphone systems: the Telefunken USA M12 or C12 (originally developed by AKG), the R-F-T M16 MkII, and the AK47. The Historic Telefunken Ela M251 microphone system entered the MIX foundation's Hall of fame in 2006. In 2008, Telefunken USA won a second TEC Award for its new Ela M 260 microphone.

As a result of a conference held in Frankfurt in May 2009, Telefunken USA has been renamed Telefunken Elektroakustik ("Electrical Acoustics") Division of Telefunken and awarded the exclusive rights to manufacture a wide variety of professional audio products and vacuum tubes bearing the Telefunken Trade Mark, in over 27 countries worldwide. Telefunken Elektroakustik now uses the Telefunken trademark for Professional Audio Equipment & Component Based Electronics, such as Capacitors, Transformers, Vacuum Tubes in North America, South America, Europe, Asia and Australia.


TELEFUNKEN HISTORY:
" It is ironic that in the years since the introduction of PAL, Telefunken – the company that invented PAL – disappeared from the market after they were bought in the 1980s by the French company Thomson – a former SECAM protagonist.
There is further irony in the fact that even as the majority of European and Asian TV viewers benefit on a daily basis from their PAL standard TV pictures, the worldwide transition from analog to digital TV spells the end of this color standard as well as many other TV transmission standards.
What we have known as PAL, SECAM, or NTSC is now increasingly known as simply digital RGB or Y, Cr, and Cb color component signals encoded in a DVB (Digital Video Broadcasting) signal or one of its many variants such as DVB-T, DVT-S, DVB-C, DVB-H, or similar ones like your ATSC.
In the future, all this may in turn disappear into an abstract IP (Internet Protocol) packet, which would make traditional distribution channels obsolete. For example, major areas in Germany, and all of Austria may terminate their analog transmissions, replacing them with DVB-T or DVB-S only.
We will find out whether the 55th anniversary of PAL in 2018 will generate much of a resonance, if all analog TV transmissions – whether terrestrial, satellite, or cable – have been brought to an end. "
1903 – 1922
TWO ARCH RIVALS. ONE INNOVATIVE COMPANY

At the beginning of the last century, two rival research groups were working in the field of
wireless telegraphy. The Slaby-Arco group was represented by the radio-telegraphy department
of AEG, founded in 1899. The other as the Braun-Siemens group, represented by a company
called Gesellschaft für drahtlose Telegraphie, System Prof. Braun und Siemens & Halske
GmbH. Under the advice of Emporer Wilhelm II, the two groups merged to form the
Gesellschaft für drahtlose Telegraphie mbH company on May 27, 1903. And the rest is history.




A TELEFUNKEN FIRST
The very first Telefunken customers were the German Army and the Imperial Navy.
Telefunken was proud to deliver the first two transmitters for the new coastal radio station, Norddeich
Radio, in November 1905. In October 1906, the expansion of a much larger Nauen station was
completed with a range of 300 km and HF output of 10 kW. Welcome to the power of
Telefunken.


MEET DR. TELEFUNKEN

Dr. Georg Graf Von Arco was the first Technical Director and Managing Director of the
Gesellschaft für drahtlose Telegraphie mbH in 1903. He was also the holder of more than one
hundred patents. Among other inventions, he initiated the high-frequency mechanical
transmitter and the wavemeter. Necessity is the mother of invention. Or in this case, German
inventions.


1923 – 1936
TELEFUNKEN GOES COMMERCIAL

On April 17, 1904, the company changed its name to "Telefunken, Gesellschaft für drahtlose
Telegraphie", and on July 26, 1932 Telefunkenplatte GmbH officially began its commercial
activity with registered capital of 100,000 Reichsmarks.
The station in the Telefunken building, Tempelhofer Ufer 9 in Berlin, began broadcasting
concerts regularly two and a half months before the official start of the "Deutsche
Rundfunkverkehr". The world tour of the Graf Zeppelin airship in 1929 got off the ground by
using Telefunken transmitters, receivers and directional equipment exclusively.
Also, on October 31, 1928, during the 5th Grand German Radio Exhibition in Berlin, Telefunken
presented a television set with the Karolus-Telefunken system, a scanning process of film
images through a Mechau projector with a Nipkow disk, in public for the first time.


MEET TELEFUNKEN’S MAD SCIENTISTS

Dr. Hans Bredow is considered to be the "Father of Broadcasting". He was employed at
Telefunken from 1904 to 1919 as a Project Manager, and later as Managing Director.
Prof. Dr. Walter Bruch developed the very first electronic television camera, with which he
participated in the live broadcast of the Olympic Summer Games in Berlin in 1936. He also
earned international fame by inventing the PAL color television system. He joined Telefunken's
Television and Physical Research Department in 1935.
These two innovators thought out of the “TV box” and helped shape and make Telefunken what
it is today.


WELCOME TO RADIO TELEFUNKEN

The German radio station in Zeesen near Königswusterhausen (8 kW shortwave transmitter) was built by Telefunken and was officially placed in service on August 28, 1929. The Mühlacker radio station (60 kW output) was handed over on December 20, 1930. Telefunken is now in, and on, the air.


TELEFUNKEN GOES FOR THE GOLD, SILVER AND BRONZE

In 1935, Telefunken equipped the Olympic Stadium, the Maifeld and the Dietrich-Eckhardt
Stage with electrical-acoustic equipment for the Olympics. On August 1, 1936 at the XI Olympic
Summer Games in Berlin, an electronic television camera, known as the Ikonoskop, was used
for the first time for a direct transmission. Again, another Telefunken first. And second. And third
1936- 1954


NOW PLAYING ON CHANNEL TELEFUNKEN

The first fully electronic television studio equipped by Telefunken for the Deutsche Reichspost
was opened with a live broadcast in August 1938. The 500 kW long wave transmitter in
Herzberg, also known as the most powerful German broadcast transmitter, was supplied by
Telefunken and began to operate on May 19, 1939.


IT’S NOT A MERGER. IT’S A POWERHOUSE

On September 24, 1941, AEG took over the 50% of Telefunken shares owned by Siemens &
Halske AG valued at 20 million Reichsmarks. Thus, Telefunken became a 100% subsidiary of
AEG. In exchange, Siemens & Halske AG received the shares of Eisenbahn-Signalwerken,
Klangfilmgesellschaft mbH and Deutsche Betriebsgesellschaft für drahtlose Telegraphie
(DEBEG) owned by AEG. Strength in numbers, indeed.


POST WWII

The reconstruction after the World War II posed a particularly difficult challenge to Telefunken.
All production facilities and equipment were destroyed, disassembled or confiscated and many
valuable experts were scattered around the world. Rebuilding began in West Germany and
Berlin in 1945, and the production of tubes and transmitters was resumed the same year. But
growth was on the way.



THE TELEFUNKEN COME BACK

In 1953 Telefunken already comprised six plants and five sales offices in Berlin, Ulm,
Frankfurt/Main and Hanover again.The range of products consisted of long-range
communications systems, radio and television transmitters, marine radios, commercial
receivers, directional and navigation systems, radar devices, deci and UHF directional radio
connections, mobile radio systems, portable radio systems, HF heat generators, measuring
equipment, electro-acoustical systems, music centers, record players, transmitter tubes, radio
tubes, special tubes and quartz crystals. As you can see, Telefunken was relentless and has
come a long way.


PROF. DR. DR. WILHELM T. RUNGE THE FIRST

Prof. Dr. Dr. Wilhelm T. Runge (1895-1987) performed trailblazing work in radio and radar
technology and played a significant role in the development of microwave in Germany. He was
especially renowned internationally in the field of high-frequency technology. As well as for
having a few, very important titles before his name.


1955 – 1962
AS TELEFUNKEN GROWS, SO DOES ITS NET WORTH

The name of the company was changed to Telefunken GmbH on January 4, 1955. Due to the
expanded business activities of Telefunken, AEG increased the capital of the company to DM
100 million in 1958.


THE FIRST GERMAN STEREO STUDIO. BROUGHT TO YOU BY TELEFUNKEN

The Sender Freies Berlin (SFB) station ordered the first German stereo studio in 1961. The
harbor radar system, supplied by Telefunken, was officially placed for service in Hamburg
Harbor in August 1962, while the first German transistor receiver (six transistors) was produced
in a test series in 1956. Prof. Dr. Walter Bruch filed the fundamental PAL "time decoder" patent
on December 31, 1962. It was the first German stereo studio of its kind, and Telefunken sought
to it that there was nothing else quite like it.


1963-1978
WHAT’S IN A NAME?

Telefunken GmbH became Telefunken AG on July 5, 1963. On June 23, 1966, the General
Shareholder Meeting of AEG passed a resolution to integrate Telefunken AG into Allgemeine
Elektrizitäts-Gesellschaft. Based on an operating lease agreement, the business activities of
Telefunken were transferred to AEG effective January 1, 1967, and were continued under the
combined name AEG-Telefunken. In March 1968, AEG-Telefunken developed a new mediumrange
radar system (Type SER-LL), which was able to detect targets at an altitude of 24,000
meters at a distance of 280 kilometers. Telefunken expands on land, as well as in the air.


TAPE RECORDERS WORTH MILLIONS

AEG-Telefunken delivered the two-millionth tape recorder, a Magnetophon 204 TS, on August
5, 1969. The ten-millionth black-and-white television picture tube was produced in Ulm on
January 27, 1970. The numbers are astounding. As is Telefunken.AEG-Telefunken delivered the
two-millionth tape recorder, a Magnetophon 204 TS, on August 5, 1969. The ten-millionth
black-and-white television picture tube was produced in Ulm on January 27, 1970. The
numbers are astounding. As is Telefunken.


ECONOMIC SLOWDOWN

There was a worldwide economic slowdown in the wake of the oil crisis in 1974. The
competition in consumer electronics sector also became more difficult due to Japanese
suppliers. The only profitable divisions of the company at this time were telecommunications
and traffic technology. But Telefunken, as usual, was known for their resilience.


1979- 1983
THE NAME GAME CONTINUES

The name of the overall company was changed to AEG-Telefunken Aktiengesellschaft on June
21, 1979. The "Aktiengesellschaft" [stock corporation] suffix was necessary due to a new law in
the European Community. In 1979, AEG-Telefunken supplied the complete telecommunications
and high-voltage equipment for the International Congress Center (ICC) Berlin, valued at DM 50
million. In January 1983 the company received an order for simulation systems for electronic
battle simulation for training Tornado crews of the German Luftwaffe and Navy. The total value
was at DM 37 million. The net worth: priceless.


TOUGH TIMES FOR TELEFUNKEN

Court composition proceedings were opened against the assets of AEG-Telefunken AG by the
District Court in Frankfurt / Main on October 31, 1982.
The District Court Frankfurt / Main confirmed the composition of AEG-Telefunken AG in
accordance with the petition filed and closed the proceedings on September 19, 1984.
Even during this difficult financial situation, AEG-Telefunken continued its business and founded
AEG-Telefunken Nachrichtentechnik GmbH (ATN), in Backnang, Germany, together with
Bosch, Mannesmann and Allianz Versicherungs-AG in 1981, as well as Telefunken electronic
GmbH (TEG) in the field of electronic components (semiconductors) together with United
Technologies Corporation (UTC), USA in 1982.
On July 1, 1992, AEG-Telefunken and Deutsche Aerospace (Dasa) founded Telefunken
Microelektronic GmbH (TEMIC), into which Telefunken Elektronic GmbH was integrated among
others. But Telefunken was determined to prevail.


A FINAL, BUT NOT LAST, TURN

Effective March 31, 1983, the French group Thomson-Brandt S.A. took over 75 percent of the
AEG-Telefunken shares in Telefunken Fernseh und Rundfunk GmbH, Hanover, Germany,
including its German and foreign subsidiaries. The remaining 25 percent were supposed to
follow on January 31, 1984. Daimler-Benz AG entered the company in autumn of 1985 and
decided in Autumn 1995 to dissolve the legal entity and transferred the remaining assets to
EHG Electroholding GmbH. Thus, the history of the company was over. But not that of its
brands.
A historical overview is offered by the company archive of AEG-Telefunken in the "Deutsches
Technikmusem Berlin", Trebbiner Str. 9, 10963 Berlin.


1984 – 2004
INNOVATION YESTERDAY. TODAY. AND TOMORROW

Currently, the Telefunken brand and name rights lie with Telefunken Licenses GmbH,
Frankfurt/Main, Germany. This company is one hundred percent subsidiary of EHG
Elektroholding GmbH, Frankfurt/Main.
EHG, on the other hand, is the legal successor of AEG Aktiengesellschaft. The licensor is
Licentia Patent-Verwaltungs GmbH, Frankfurt/Main, Germany. A differentiation is made
between brand licensing agreements, name use agreements and combined agreements. And
third-party use always requires the written approval of the licensor.
In 2003, Telefunken can look back at one-hundred years of brand history. In the past,
Telefunken was associated with significant technical developments and enjoyed the reputation
of a successful German company.
The Telefunken brand is registered in the official trademark registries of 118 countries. It
continues to be used under a variety of licensing agreements.
These are the topics that can be found in the commemorative volume "Telefunken After 100
Years - The Legacy of a Global German Brand."
Whether discovered on this website or in book, these topics should not only focus attention on
the past, but also simultaneously highlight the beginning of a strong Telefunken brand. Simply
put, it’s not just about where we’ve been. But also where we’re going.


2004 – 2009
TELEFUNKEN TODAY

Since December 2007, the trademark-right TELEFUNKEN rests with TELEFUNKEN Holding
AG, Frankfurt. Currently, TELEFUNKEN is the owner of more than 20,000 patents and active in over 130 countries around the globe.
Today, TELEFUNKEN stands for innovation and progress in the ever-changing world of
information and communications technology and is strictly focused on consumer quality – from
design concept to execution. And because of its strong heritage and long-standing tradition,
Telefunken has a high brand-awareness and a clear positioning in the field of premium
products.

Some References:

  • M. Friedewald: Telefunken und der deutsche Schiffsfunk 1903–1914. In: Zeitschrift für Unternehmensgeschichte 46. Nr. 1, 2001, S. 27–57
  • M. Fuchs: Georg von Arco (1869–1940) – Ingenieur, Pazifist, Technischer Direktor von Telefunken. Eine Erfinderbiographie. Verlag für Geschichte der Naturwissenschaften und der Technik, Berlin & München: Diepholz 2003
  • L. U. Scholl: Marconi versus Telefunken: Drahtlose Telegraphie und ihre Bedeutung für die Schiffahrt. In: G. Bayerl, W. Weber (ed.): Sozialgeschichte der Technik. Ulrich Troitzsche zum 60. Geburtstag. Waxmann, Münster 1997 (Cottbuser Studien zur Geschichte von Technik, Arbeit und Umwelt, 7)
  • Telefunken Sendertechnik GmbH: 90 Jahre Telefunken. Berlin 1993
  • Erdmann Thiele (ed.): Telefunken nach 100 Jahren – Das Erbe einer deutschen Weltmarke. Nicolaische Verlagsbuchhandlung, Berlin 2003, ISBN 3-87584-961-2
  •  

Einzelnachweise:

Schreibweise mit c siehe: - AEG-Teilschuldverschreibung von 1962

Marke „Telefunken“ in der Registerauskunft des Deutschen Patent- und Markenamtes (DPMA)

E. Thiele (Hrsg.): Telefunken nach 100 Jahren: Das Erbe einer deutschen Weltmarke. Nicolai, Berlin 2003, S. 19

Kurt Kracheel: Flugführungssysteme (Die Deutsche Luftfahrt, Band 20). Bernard&Graefe Verlag, Bonn 1993, ISBN 3-7637-6105-5, S. 119.

Operette 50W UKW. In: radiomuseum.org. Abgerufen am 28. Januar 2016.

Autosuper IA 50. In: radiomuseum.org. Abgerufen am 28. Januar 2016.

Farbfernseh-Tischempfänger PALcolor 708T. In: radiomuseum.org. Abgerufen am 28. Januar 2016.

Mini Partner 101. In: radiomuseum.org. Abgerufen am 28. Januar 2016.

Olympia-Partner. In: radiomuseum.org. Abgerufen am 28. Januar 2016.

Magnetophon 3000 hifi. In: radiomuseum.org. Abgerufen am 28. Januar 2016.

Fernseh-Tischempfänger FE8T. In: radiomuseum.org. Abgerufen am 28. Januar 2016.

Israelischer Konzern Elbit Systems eröffnet Büro in Berlin. In: bundeswehr-journal. 13. April 2018, abgerufen am 18. Januar 2019.

Telefunken Semiconductors Heilbronn: Die Lichter sind für immer aus, swr.de, 27. Februar 2015

LDL Berlin: Geschäftshaus Mehringdamm 32 & 34

LDL Berlin: AEG-Glühlampenfabrik

LDL Berlin: AEG-Telefunken-Gerätewerk

Telefunkenwerk Celle. vergessene-orte.blogspot.com

Ludwig Leisentritt: Die historische Entwicklung von Zeil am Main, hbrech.tripod.com
 
 

 

CGE CT 8826 TV 26" TELECOLOR (TELEFUNKEN) CHASSIS 712A INTERNAL VIEW

 

The TELEFUNKEN CHASSIS 712A was introducing first time a SMPS POWER SUPPLY and chroma combined 3 chips design in video sections and further using the 20AX SYSTEM CRT TUBE BUT HERE MADE BY TELEFUNKEN FACTORY. It's mainly a modular chassis and highly sophisticated and complex.  

This chassis THE TELEFUNKEN CHASSIS 712A was even featuring a DYNAMIC FOCUS in the Line deflection EHT circuitry. Dynamic focus voltages for a CRT are obtained by utilizing the combined parabolic conversion wave shapes for control of the focusing electrode to provide sharp focus at all points in the raster. A current source is coupled to the focus divider chain and the conversion wave shape controls the current in the divider chain by controlling the resistance in a transistor. No high voltage capacitors are required since the dynamic voltages are coupled into the chain near the low voltage end. 1. In a cathode ray tube device for displaying information by means of a raster:

a cathode ray tube having an anode and a focus electrode;

an input source of AC voltage having variations of substantially parabolic waveform at both horizontal and vertical rates;

a source of high voltage DC coupled to the anode;

transistor means for amplifying said input AC voltage and coupled to ground and to the ac input source; and

resistive means including first and second elements, the first element coupled between the source of high voltage and the focus electrode, the second element coupled between the focus electrode and the transistor means, the first element having a resistance substantially greater than that of the second element.

2. A cathode ray tube device for displaying information on a raster in accordance with claim 1 and wherein the resistive means also includes a manually variable resistive means. 3. A cathode ray tube device for displaying information on a raster in accordance with claim 2 wherein the manually controllable resistive means is a focus control. 4. A cathode ray tube device for displaying information on a raster in accordance with claim 1 and further including an amplifier stage coupled between the source of AC voltage and the transistor means. 5. A cathode ray tube device for displaying information on a raster in accordance with claim 1 and wherein said lower DC voltage is manually variable. 6. A cathode ray tube device for displaying information on a raster in accordance with claim 1 and further including a source of relatively low voltage DC coupled to the junction of the second resistive means element and the transistor means. 7. A cathode ray tube device for displaying information on a raster in accordance with claim 6 wherein the source of relatively low voltage DC is coupled to the junction through a clamping diode means and a biasing resistive means.
Description:

BACKGROUND OF THE INVENTION

This invention relates to the field of cathode ray tubes and, more particularly, to the provision for dynamic focusing voltages for use in such tubes.

In CRT devices, the major factor effecting spot focus is the variation in the distance from the electron gun to the fluorescent screen as the electron beam is swept from the center of the screen to the outer areas. For accurate focusing of the beam at all parts of the screen, the voltage applied to the focus electrode must be varied as a function of the distance from the spot to the Z axis of the CRT device, or, in other words, a function of the angle of deflection. This requires a voltage which varies as the beam moves horizontally and also as it moves vertically. As a reasonable approximation, this requires a horizontal voltage variation at line rate which is of essentially parabolic shape, and which is superimposed on a similar function at the vertical frame rate. Earlier CRT designs provided minimum spot de-focusing by optimizing focus at some point intermediate the center of the CRT screen and the edges of the raster; e.g., 30° from the Z axis was typical. Later it was recognized that a better solution would be to add to the static focusing voltage a voltage varying with the angle of deflection. All known circuits for accomplishing dynamic focusing in this way have required high voltage coupling capacitors and thus were expensive and not adaptable to solid state implementation.

SUMMARY OF THE INVENTION

It is therefore an object of the present invention to provide dynamic focusing for a CRT utilizing waveforms which are already present in the CRT device.

It is a more particular object to devise such dynamic focusing with solid state circuitry and without large and costly high voltage capacitors.

These objects and others are provided by circuitry constructed in accordance with the invention in which the effective resistance of a transistor circuit is varied as a function of the convergence waveform. The transistor circuit is coupled in series with the focus divider chain, thus the current in the chain is varied accordingly. No high voltage capacitors are required for coupling the dynamic focus voltage to the CRT device since the transistor is near the low voltage end of the divider chain. The convergence waveform is a combination of two waveforms, one at line rate and one at frame rate, each essentially of parabolic form.

BRIEF DESCRIPTION OF THE DRAWING

FIG. 1a is a diagram of a CRT device showing the dimensional basis for the problem which is solved by the invention.

FIG. 1b is a diagram of a dot pattern of a CRT device lacking the circuit of the invention.

FIGS. 2a-2c are illustrations of the voltage waveforms required for the invention.

FIG. 3 is a block diagram of a device utilizing a CRT and including the invention.

FIG. 4 is an embodiment of the circuitry of the invention.

DETAILED DESCRIPTION OF THE PREFERRED EMBODIMENT

The diagram of FIG. 1a is intended to make clear the problem to be solved by the circuit of the invention. A 3-gun cathode ray tube (CRT) 10 of the type used in color television is shown in outline form. Such tubes typically have a rounded face plate or screen 11 (bearing the phosphors) with a radius of curvature R' longer than the entire tube length, however, the invention is applicable even to flat face plate tubes. The electron beam thus travels a path R2 from the point of deflection B to the edges of the screen 11 which is longer than the path R1 to the central portion, ΔR being the instantaneous difference. It will be seen then that the focusing voltage must be adjusted to compensate for this difference as the electron beam is swept from side to side and top to bottom of a raster.

FIG. 1b is a graphical representation of the spot defocusing which occurs at the outer portions of a CRT screen if dynamic focusing is not used. Instead of providing a sharp focus spot, as at the center of the screen, a small circle is produced which reduces the definition of the displayed information.

FIG. 2 shows the types of waveforms needed to provided dynamic focusing and eliminate the de-focusing effect of FIG. 1b. As may be seen in FIG. 2a, a roughly parabolic waveform repeating at frame rate, is needed for the vertical dimension. A similar waveform, FIG. 2b, but repeating at line rate, is needed for the horizontal dimension. FIG. 2c illustrates the combined waveform with the horizontal rate greatly reduced for clarity. As may be seen, no dynamic focusing voltage is applied as the electron beam sweeps the central portion of the screen.

FIG. 3 is a block diagram of a typical video receiver utilizing a raster to display information and is given here only for a better understanding of the invention as the invention could, for example, be utilized in a monitor which lacks much of this circuitry. The RF amplifier 12, local oscillator 13, mixer 14, IF amplifier 15, detector 16, sound portion 17, video amplifier 18 and color demodulator 19 all function as is well known in the art. The detector 16 output is also coupled to sync circuits 20, which provide synchronization for vertical and horizontal sweep circuits 21 and 22 respectively. The sync signals are coupled to the CRT 10 for providing a raster on the screen 11 of the tube. The sweep circuits 21 and 22 are also coupled to a convergence circuit 24 which is coupled to the CRT 10.

The vertical and horizontal sweep circuits 21 and 22 are coupled to the convergence circuit 24 which is connected to the convergence coil of the CRT 10. In this embodiment of the invention the convergence circuit 24 is also coupled through a dynamic focus circuit 26 to the focus circuit 27 which is coupled to the CRT 10.

FIG. 4 is a schematic diagram of one embodiment of the dynamic focus circuit of the invention. The terminal 30 is coupled to an amplifier including a transistor Q1. The terminal 30 could be coupled through the convergence circuit 24 as shown in FIG. 3 or from the pin cushion circuitry (not shown) which also has the vertical rate parabolic waveform. A terminal 31 may couple an input signal, as from the convergence circuit, which has the desired parabolic waveform at the horizontal or line rate. A terminal 33 is coupled to a high voltage source; i.e., the CRT anode voltage supply. Forming a voltage divider across the high voltage is a tapped resistor R1, a potentiometer or variable resistor R2 (the "focus" control) and a transistor Q2. The tap on resistor R1 is coupled to the focus electrode of the CRT by way of a terminal 34. It will be seen that the voltage on the terminal 34 can be varied or modulated by varying the effective resistance of the transistor Q2. A low voltage is coupled from a terminal 36 to the collector of the transistor Q2 by way of a biasing transistor R3 and a clamping diode D1. The voltage on terminal 36 is preferably a variable voltage to provide for the slight variations which occur from one CRT to another. A resistor R4 provides a feedback path, and a resistor R5 and a capacitor C1 provide the necessary time constant. Once the focus control R2 is set to provide minimum beam spot size at the center of the screen, the added voltage, having parabolic waveforms at both horizontal and vertical rate, will optimize the focusing at the edges of the raster.

Thus, there has been shown and described a means of providing dynamic focusing for a CRT by using a voltage such as the pin cushion correction voltage or the dynamic convergence voltage to control the effective resistance of a solid state circuit which in turn controls the current in the focus circuit of a CRT.

It will be apparent that there are a number of variations and modifications of the above-described embodiment and it is intended to include all such as fall within the spirit and scope of the appended claims.

CGE CT 8826 TV 26" TELECOLOR  (TELEFUNKEN)  CHASSIS 712A   POWER SUPPLY UTILIZING A DIODE AND CAPACITOR VOLTAGE MULTIPLIER FOR TRACKING FOCUSING AND ULTOR VOLTAGES A television receiver high voltage power supply includes an ultor voltage output and an output voltage at some potential lower than the ultor voltage. The supply is responsive to kinescope beam current to vary the proportionate magnitudes of the high and lower voltages at some predetermined ratio. 1. In a television receiver electron beam deflection system, a power supply comprising: 2. A circuit as defined in claim 1 wherein said voltage multiplying means comprise at least: 3. A circuit as defined in claim 1 wherein: 4. A circuit as defined in claim 3 wherein said lower voltage output means further comprises: 5. A circuit as defined in claim 1 wherein said lower output voltage means comprises a focus voltage supply in a television receiver. 6. In a television receiver electron beam deflection circuit, a power supply comprising: 7. A circuit as defined in claim 6 and further comprising: 8. A circuit as defined in claim 6 wherein said lower output voltage means comprises a focus voltage in a television receiver.
Description:
POWER SUPPLY This invention relates to high direct voltage power supplies and more particularly to television receiver high voltage and focus voltage supplies employing voltage multiplier arrangements. In a television receiver, electron beam focusing in the kinescope is commonly achieved by utilizing an electrostatic focusing lens. For optimum focusing, it is necessary to vary the strength of the focusing lens with varying beam current and electron velocity (i.e., electron beam accelerating voltage). The focusing lens may comprise, for example, a pair of cylindrically shaped members mounted along the kinescope gun axis and having a separating space between them. Focusing is accomplished by the electric field produced by the geometry of the focusing members and the potential difference between them --that is, by the shape and magnitude of the focusing field. In order to maintain a beam or beams of electrons in optimum focus under varying beam current conditions and differing electron beam velocities, it is necessary to vary the focusing field. Since the geometry of the focusing members is fixed, it is necessary to adjust the voltage difference between these members to effect proper focusing. As beam current increases, if the high voltage (the accelerating potential of the electron beam) remains substantially constant, as is the case with a regulated high voltage supply, a stronger focusing lens is needed to maintain focusing of the electron beam. The strength of the focusing lens can be increased, where, as in a color television receiver, the focusing members are coupled to a focus voltage supply and the high beam-accelerating voltage supply, respectively, by decreasing the output of the focus voltage supply to increase the potential gradient across the focusing lens. Thus, if the high voltage is constant and the beam current increases, the focus voltage as a percentage of the high voltage should be decreased to maintain focus at high beam current levels. Further, if the high voltage (electron-accelerating potential) is not maintained constant but decreases somewhat, and therefore the electron velocity decreases as beam current increases, the strength of the focusing lens should be increased which again requires a reduction in focus voltage. The percentage reduction in focus voltage customarily is equal to or greater than the corresponding percentage reduction in high voltage. This effect is commonly referred to as "focus tracking."
In television receivers, it is common to develop the high voltage from a secondary winding on the horizontal deflection output transformer. The flyback pulses developed during horizontal retrace are stepped up by the flyback transformer and rectified to produce the necessary high voltage. Further, it is common to provide separate rectifying means coupled to a lower voltage tap on the flyback transformer, to develop a focus voltage in a color television receiver. U.S. Pat. No. 2,879,447 (issued to J. O. Preisig) assigned to the present assignee discloses such an arrangement including means for obtaining the necessary "focus tracking" described above. The present invention obviates the need for separate transformer windings for the high voltage and focus voltage supplies but provides the desired focus tracking while deriving both high voltage (beam-accelerating voltage) and focus voltage from a common point on the horizontal output transformer by means of a voltage multiplier arrangement. Circuits embodying the present invention include a horizontal output transformer having a high voltage winding, voltage-multiplying means coupled to the high voltage winding for producing the ultor voltage for a television receiver, and lower voltage output means associated with the voltage multiplying means and responsive to beam current for producing a voltage which tracks with the ultor voltage. A better understanding of the present invention and its features and advantages can be obtained by reference to the single FIGURE and the description below. In the drawing, a voltage supply constructed in accordance with the present invention is illustrated partially in block and partially in schematic form. Referring to the FIGURE, horizontal deflection circuits 10 include a horizontal output stage (not shown) which produces a generally sawtooth current waveform characterized by a relatively slow rise time during a trace portion of each deflection cycle and a relatively rapid fall time during a retrace portion of each deflection cycle. For clarity, the deflection windings and associated horizontal output circuitry are not shown. Such a circuit is shown in detail in RCA Television Service Data 1968 No. 20, published by RCA Sales Corporation, Indianapolis, Indiana. It is sufficient for the purposes of the present invention to note that during the retrace portion of each deflection cycle, energy in the form of a voltage pulse commonly referred to as a flyback pulse is coupled by means of a primary winding 11 of a horizontal output transformer 12 to a secondary winding 13 thereof. The turns ratio of transformer 12 is selected to step up the voltage of this flyback pulse appearing at a high voltage terminal 14 on secondary winding 13. The voltage magnitude of this flyback pulse is partially dependent upon the turns ratio of transformer 12 and in the circuit illustrated is of the order of 6.25 kilovolts. This will produce an ultor voltage (V 1 ) of approximately 25 kilovolts at ultor output terminal 40 when applied to the voltage quadrupler described below. The voltage multiplier may be designed to multiply by any number n by adding or subtracting successive stages of multiplication. Thus, the necessary stepped up flyback voltage magnitude will be approximately V 1 /n where V 1 is the desired ultor voltage at terminal 40 and n is the number of stages of multiplication. When the system is initially put into operation, positive flyback pulses will cause a first undirectional conductive device such as a diode 18 to be forward biased and conduct to charge a focus output charge storage device such as a capacitor 21 in the polarity shown and at a potential nearly equal to the peak flyback voltage appearing at high voltage terminal 14. As the flyback pulse decreases from its peak value, a second unidirectional conductive device 20 will then be forward biased, since its anode connected to terminal 50 will be more positive than its cathode, the latter being at the same voltage as terminal 14 at this time. When device 20 conducts, at least a portion of the charge on the output or focus charge storage device 21 is transferred to a first charge storage device 15 in the polarity shown. The transfer of charge continues during successive deflection cycles by the conduction of a third unidirectional conductive device 22 to charge a second charge storage device 23, the conduction of a fourth unidirectional conductive device 24 to charge a third charge storage device 17, the conduction of a fifth unidirectional conductive device 26 to charge a fourth charge storage device 25, the conduction of a sixth unidirectional conductive device 28 to charge a fifth charge storage device 19, and the conduction of a seventh unidirectional conductive device 30 to charge a final charge storage device 27. Assuming there are no losses within the system and no current is being drawn from the system as successive flyback pulses occur, the charge storage devices mentioned, with the exception of devices 15 and 21 as will be explained below, will each become charged to approximately the peak to peak value of the transformed flyback pulse waveform illustrated on the drawing. The charge storage device 21 charges only during the positive flyback pulse portion of the waveform and, as a consequence of a resistor 16 coupled in series with conductive device 18, charges to a voltage less than the peak amplitude of the flyback pulse. Therefore, when conductive device 20 conducts, storage device 15 charges to a voltage equal to the voltage across storage device 21 plus the negative voltage at terminal 14 occurring between flyback pulses (i.e., less than the peak-to-peak value of the waveform at terminal 14 by, for example, 200 volts). Adding the series voltages across charge storage devices 21, 23, 25 and 27, the output voltage at terminal 40 will be approximately three times the peak to peak flyback voltage plus the voltage across storage device 21 or almost four times the peak-to-peak flyback voltage. Kinescope charge storage device 29, illustrated in dotted lines, is the capacitance of the aquadag coating on the associated kinescope to ground. A resistance 31 is serially coupled from the final charge storage device 27 to an output terminal 40 and serves as a current-limiting resistance to protect the horizontal output circuit in the event of kinescope arcing.
As current is drawn from the system due to a flow of beam current within the kinescope, charge storage devices 21, 23, 25, 27 and 29 begin to discharge to supply the output current. As this occurs, the voltage across these devices will decrease. The unidirectional conductive devices 22, 26 and 30 conduct to equalize the voltage across storage devices in the upper series connection (in the drawing) with those across devices in the lower series connection. The flyback pulse will be coupled via charge storage devices 15, 17 and 19 and unidirectional conductive devices 18, 20, 26 and 30 will conduct when forward biased to restore the charge on the charge storage devices. Unidirectional devices 20, 24 and 28 then conduct to again equalize voltages. A mean direct current will flow through the charge transfer unidirectional conductive devices and resistance 16 serially coupled to the first unidirectional conductive device 18. As beam current increases, this mean current increases, thus developing a larger voltage drop across resistance 16. Since the voltage at terminal 50 is approximately one-quarter that of the ultor voltage V 1 at terminal 40, and since resistance 16 is relatively large as compared with the forward resistance of the unidirectional conductive devices, the percentage decrease of the voltage V 2 present at terminal 50 will be greater than the percentage decrease of the ultor voltage present at terminal 40 for high beam current. The utilization of resistance 16 in series relation to unidirectional conductive device 18 provides the proper relationship between the focus voltage and ultor voltage. It is noted that although resistance 16 is illustrated as a separate element, it may be incorporated within a unidirectional conductive device as for example, one having a higher forward resistance than the remaining devices 20, 22, 24, 26, 28 and 30. A voltage dividing network comprising resistors 32, 34 and 36 serially coupled from terminal 50 to ground provide a network from which an adjustable voltage V 3 can be extracted by means of a variable resistor 34. Although the present invention is particularly suitable for focus tracking applications, it may be useful wherever a voltage which is responsive to beam current is desired. The parameters listed below have been utilized in the preferred embodiment. Capacitors 15, 17, 19 21, 23, 25, 27 2,000 picofarads Capacitor 29 2,500 picofarads Resistors 16 22 kiloohms 31 10 kiloohms Resistors 32 5 megohms 34 15 megohms 36 30 megohms Diodes 18, 20, 22 9 kilovolt peak inverse voltage,5 milliamp 24,26,28,30 5 ampere surge.
Other References:
IBM Technical Disclosure Bulletin, vol. 17, No. 4, Sep. 1974, K. H. Knickmeyer, pp. 1091-1092. Arentsen et al, Electronic Applications, vol. 34, No. 2, Philips Semiconductor Application Lab., pp. 52-60. Loewe Opta, Circuit Schematic, Aug. 1st, 1980. Thomson-Brandt, Circuit Schematic, Apr. 15th, 1981. Blaupunkt, Circuit Schematic, (undated). Grundig, Circuit Schematic, (undated). ITT, Circuit Schematic, (undated). Telefunken, Circuit Schematic, (undated). Schneider, Circuit Schematic, (undated). 
 

 
CRT   TV EHT VOLTAGE MULTIPLIER - KASKADE COCKCROFT-WALTON CASCADE CIRCUIT FOR VOLTAGE MULTIPLICATION:




A Cockcroft-Walton cascade circuit comprises an input voltage source and a pumping and storage circuit with a series array of capacitors with pumping and storage portions of the circuit being interconnected by silicon rectifiers, constructed and arranged so that at least the capacitor nearest the voltage source, and preferably one or more of the next adjacent capacitors in the series array, have lower tendency to internally discharge than the capacitors in the array more remote from the voltage source.


1. An improved voltage multiplying circuit comprising,

2. An improved voltage multiplying circuit in accordance with claim 1 wherein said first pumping capacitor is a self-healing impregnated capacitor which is impregnated with a high voltage impregnant.

3. An improved voltage multiplying circuit in accordance with claim 1 wherein said first pumping capacitor comprises a foil capacitor.

Description:
BACKGROUND OF THE INVENTION

The invention relates in general to Cockcroft-Walton cascade circuits for voltage multiplication and more particularly to such circuits with a pumping circuit and a storage circuit composed of capacitors connected in series, said pumping circuits and storage circuit being linked with one another by a rectifier circuit whose rectifiers are preferably silicon rectifiers, especially for a switching arrangement sensitive to internal discharges of capacitors, and more especially a switching arrangement containing transistors, and especially an image tube switching arrangement.

Voltage multiplication cascades composed of capacitors and rectifiers are used to produce high D.C. voltages from sinusoidal or pulsed alternating voltages. All known voltage multiplication cascades and voltage multipliers are designed to be capacitance-symmetrical, i.e., all capacitors used have the same capacitance. If U for example is the maximum value of an applied alternating voltage, the input capacitor connected directly to the alternating voltage source is charged to a D.C. voltage with a value U, while all other capacitors are charged to the value of 2U. Therefore, a total voltage can be obtained from the series-connected capacitors of a capacitor array.

In voltage multipliers, internal resistance is highly significant. In order to obtain high load currents on the D.C. side, the emphasis in the prior art has been on constructing voltage multipliers with internal resistances that are as low as possible.

Internal resistance of voltage multipliers can be reduced by increasing the capacitances of the individual capacitors by equal amounts. However, the critical significance of size of the assembly in the practical application of a voltage multiplier, limits the extent to which capacitance of the individual capacitors can be increased as a practical matter.

In television sets, especially color television sets, voltage multiplication cascades are required whose internal resistance is generally 400 to 500 kOhms. Thus far, it has been possible to achieve this low internal resistance with small dimensions only by using silicon diodes as rectifiers and metallized film capacitors as the capacitors.

When silicon rectifiers are used to achieve low internal resistance, their low forward resistance produces high peak currents and therefore leads to problems involving the pulse resistance of the capacitors. Metallized film capacitors are used because of space requirements, i.e., in order to ensure that the assembly will have the smallest possible dimensions, and also for cost reasons. These film capacitors have a self-healing effect, in which the damage caused to the capacitor by partial evaporation of the metal coating around the point of puncture (pinhole), which develops as a result of internal spark-overs, is cured again. This selfhealing effect is highly desirable as far as the capacitors themselves are concerned, but is not without its disadvantages as far as the other cirucit components are concerned, especially the silicon rectifiers, the image tubes, and the components which conduct the image tube voltage.

It is therefore an important object of the invention to improve voltage multiplication cascades of the type described above.

It is a further object of the invention to keep the size of the entire assembly small and the internal resistance low.

It is a further object of the invention to increase pulse resistance of the entire circuit.

It is a further object of the invention to avoid the above-described disadvantageous effects on adjacent elements.

It is a further object of the invention to achieve multiples of the foregoing objects and preferably all of them consistent with each other.

SUMMARY OF THE INVENTION

In accordance with the invention, the foregoing objects are met by making at least one of the capacitors in the pumping circuit, preferably including the one which is adjacent to the input voltage source, one which is less prone to internal discharges than any of the individual capacitors in the storage circuit.

The Cockcroft-Walton cascade circuit is not provided with identical capacitors. Instead, the individual capacitors are arranged according to their loads and designed in such a way that a higher pulse resistance is attained only in certain capacitors. It can be shown that the load produced by the voltage in all the capacitors in the multiplication circuit is approximately the same. But the pulse currents of the capacitors as well as their forward flow angles are different. In particular, the capacitors of the pumping circuit are subjected to very high loads in a pulsed mode. In the voltage multiplication cascade according to the invention, these capacitors are arranged so that they exhibit fewer internal discharges than the capacitors in the storage circuit.

The external dimensions of the entire assembly would be unacceptably large if one constructed the entire switching arrangement using such capacitors.

The voltage multiplication cascade according to the invention also makes it possible to construct a reliably operating

arrangement which has no tendency toward spark-overs, consistent with satisfactory internal resistance of the voltage multiplication cascade and small dimensions of the entire assembly. This avoids the above cited disadvantages with respect to the particularly sensitive components in the rest of the circuit and makes it possible to design voltage multiplication cascades with silicon rectifiers, which are characterized by long lifetimes. Hence, a voltage multiplication cascade has been developed particularly for image tube circuits in television sets, especially color television sets, and this cascade satisfies the highest requirements in addition to having an average lifetime which in every case is greater than that of the television set.

A further aspect of the invention is that at least one of the capacitors that are less prone to internal discharges is a capacitor which is impregnated with a high-voltage impregnating substance, especially a high-voltage oil such as polybutene or silicone oil, or mixtures thereof. In contrast to capacitors made of metallized film which have not been impregnated, this allows the discharge frequency due to internal discharges or spark-overs to be reduced by a factor of 10 to 100.

According to a further important aspect of the invention, at least one of the capacitors that are less prone to internal discharges is either a foil capacitor or a self-healing capacitor. In addition, the capacitor in the pumping circuit which is adjacent to the voltage source input can be a foil capacitor which has been impregnated in the manner described above, while the next capacitor in the pumping circuit is a self-healing capacitor impregnated in the same fashion.

Other objects, features and advantages of the invention will be apparent from the following detailed description of preferred embodiments, taken in connection with the accompanying drawing, the single FIGURE of which:

BRIEF DESCRIPTION OF THE DRAWING

is a schematic diagram of a circuit made according to a preferred embodiment of the invention.

DETAILED DESCRIPTION OF PREFERRED EMBODIMENTS

The voltage multiplier comprises capacitors C1 to C5 and rectifiers D1 to D5 connected in a cascade. An alternating voltage source UE is connected to terminals 1 and 2, said voltage source supplying for example a pulsed alternating voltage. Capacitors C1 and C2 form the pumping circuit while capacitors C3, C4 and C5 form the storage circuit.

In the steady state, capacitor C1 is charged to the maximum value of the alternating voltage UE as are the other capacitors C2 to C5. The desired high D.C. voltage UA is picked off at terminals 3 and 4, said D.C. voltage being composed of the D.C. voltages from capacitors C3 to C5. Terminal 3 and terminal 2 are connected to one pole of the alternating voltage source UE feeding the circuit, which can be at ground potential. In the circuit described here, a D.C. voltage UA can be picked off whose voltage value is approximately 3 times the maximum value of the pulsed alternating voltage UE. By using more than five capacitors, a correspondingly higher D.C. voltage can be obtained.


The individual capacitors are discharged by disconnecting D.C. voltage UA. However, they are constantly being recharged by the electrical energy supplied by the alternating voltage source UE, so that the voltage multiplier can be continuously charged on the output side.

According to the invention, in this preferred embodiment, capacitor C1 and/or C2 in the pumping circuit are designed so that they have a lower tendency toward internal discharges than any of the individual capacitors C3, C4 and C5 in the storage circuit.

It is evident that those skilled in the art, once given the benefit of the foregoing disclosure, may now make numerous other uses and modifications of, and departures from the specific embodiments described herein without departing from the inventive concepts. Consequently, the invention is to be construed as embracing each and every novel feature and novel combination of features present in, or possessed by, the apparatus and techniques herein disclosed and limited solely by the scope and spirit of the appended claims.

Inventors:Petrick, Paul (Landshut, DT)
Schwedler, Hans-peter (Landshut, DT)
Holzer, Alfred (Schonbrunn, DT)
ERNST ROEDERSTEIN SPEZIALFABRIK

US Patent References:
3714528    ELECTRICAL CAPACITOR WITH FILM-PAPER DIELECTRIC    1973-01-30    Vail    
3699410    SELF-HEALING ELECTRICAL CONDENSER    1972-10-17    Maylandt    
3463992    ELECTRICAL CAPACITOR SYSTEMS HAVING LONG-TERM STORAGE CHARACTERISTICS    1969-08-26    Solberg    
3457478    WOUND FILM CAPACITORS    1969-07-22    Lehrer    
3363156    Capacitor with a polyolefin dielectric    1968-01-09    Cox    
2213199    Voltage multiplier    1940-09-03    Bouwers et al.    

CGE CT 8826 TV 26" TELECOLOR  (TELEFUNKEN)  CHASSIS 712A   TELEFUNKEN CHASSIS 712A Switching Power supply voltage stabilizer: A power supply voltage stabilizer comprising a transformer, of which the primary winding is connected to a switching means for controlling power supply to the primary winding. An oscillator circuit is associated with the switching means in order to control on/off operation of the switching means. An abnormal overvoltage and/or overcurrent detection circuit is provided for terminating the oscillation operation of the oscillator circuit when impending overvoltage and/or overcurrent is detected. 1. A power supply voltage stabilizer comprising:

a transformer including a primary winding connected to a power source and a secondary winding for output purposes;

switching means connected to said primary winding for controlling power supply to said primary winding;

an oscillator circuit for controlling on/off operation of said switching means; and

abnormal condition detection means for developing a control signal for terminating oscillation operation of said oscillator circuit when an abnormal condition is detected;

said oscillator circuit including an astable multivibrator, and variable impedance means for varying an oscillation frequency of said astable multivibrator.

2. A power supply voltage stabilizer comprising:

a transformer including a primary winding connected to a power source and a secondary winding for output purposes;

switching means connected to said primary winding for controlling power supply to said primary winding;

an oscillator circuit for controlling on/off operation of said switching means; and

abnormal condition detection means for developing a control signal for terminating oscillation operation of said oscillator circuit when an abnormal condition is detected;

said transformer further including an auxiliary winding for developing a voltage proportional to that developed through said secondary winding, said voltage developed through said auxiliary winding being applied to said oscillator circuit for driving said oscillator circuit;

said abnormal condition detection means including an overvoltage detection circuit connected to said auxiliary winding for developing said control signal when an overvoltage is developed through said auxilliary winding;

said oscillator circuit comprising an astable multivibrator, and variable impedance means for varying an oscillation frequency of said astable multivibrator.

3. A power supply voltage stabilizer comprising:

a transformer including a primary winding connected to a power source and a secondary winding for output purposes;

switching means connected to said primary winding for controlling power supply to said primary winding;

an oscillator circuit for controlling on/off operation of said switching means; and

abnormal condition detection means for developing a control signal for terminating oscillation operation of said oscillator circuit when an abnormal condition is detected;

said transformer further including an auxiliary winding for developing a voltage proportional to that developed through said secondary winding, said voltage developed through said auxiliary winding being applied to said oscillator circuit for driving said oscillator circuit;

said abnormal condition detection means including an overvoltage detection circuit connected to said auxiliary winding for developing said control signal when an overvoltage is developed through said auxiliary winding;

said overvoltage detection circuit including a latching means for continuously developing said control signal.

4. A power supply voltage stabilizer comprising:

a transformer including a primary winding connected to a power source and a secondary winding for output purposes;

switching means connected to said primary winding for controlling power supply to said primary winding;

an oscillator circuit for controlling on/off operation of said switching means;

abnormal condition detection means for developing a control signal for terminating oscillation operation of said oscillator circuit when an abnormal condition is detected;

said transformer further including an auxiliary winding for developing a voltage proportional to that developed through said secondary winding, said voltage developed through said auxiliary winding being applied to said oscillator circuit for driving said oscillator circuit;

said abnormal condition detection means including an overvoltage detection circuit connected to said auxiliary winding for developing said control signal when an overvoltage is developed through said auxiliary winding;

said overvoltage detection circuit further includes,

a reference voltage generation means for developing a reference voltage proportional to a voltage applied from said power source; and

comparing means for comparing said voltage developed through said auxiliary winding with said reference voltage in order to develop said control signal when said voltage developed through said auxiliary winding exceeds said reference voltage.

5. A power supply voltage stabilizer comprising:

a transformer including a primary winding connected to a power source and a secondary winding for output purposes;

switching means connected to said primary winding for controlling power supply to said primary winding;

an oscillator circuit for controlling on/off operation of said switching means; and

abnormal condition detection means for developing a control signal for terminating oscillation operation of said oscillator circuit when an abnormal condition is detected;

said abnormal condition detection means including an overcurrent detection circuit connected to said primary winding for developing said control signal when an overcurrent flows through said primary winding;

wherein said oscillator circuit includes an astable multivibrator, and variable impedance means for varying an oscillation frequency of said astable multivibrator.

6. A power supply voltage stabilizer comprising:

a transformer including a primary winding connected to a power source and a secondary winding for output purposes;

switching means connected to said primary winding for controlling power supply to said primary winding;

an oscillator circuit for controlling on/off operation of said switching means; and

abnormal condition detection means for developing a control signal for terminating oscillation operation of said oscillator circuit when an abnormal condition is detected;

said abnormal condition detection means including an overcurrent detection circuit connected to said primary winding for developing said control signal when an overcurrent flows through said primary winding;

said overcurrent detection circuit including a latching means for continuously developing said control signal;

said oscillator circuit including an astable multivibrator, and variable impedance means for varying an oscillation frequency of said astable multivibrator.

7. The power supply voltage stabilizer of claim 1, 2, 5, or 6, wherein said variable impedance means comprise a photo transistor, and wherein a light emitting diode is connected to said secondary winding for emitting a light of which amount is proportional to a voltage developed through said secondary winding, said light emitted from said light emitting diode being applied to said photo transistor. 8. The power supply voltage stabilizer of claim 7, wherein said light emitting diode and said photo transistor are incorporated in a single photo coupler. 9. A power supply voltage stabilizer comprising:

a transformer including a primary winding connected to a power source and a secondary winding for output purposes;

switching means connected to said primary winding for controlling power supply to said primary winding;

an oscillator circuit for controlling on/off operation of said switching means; and

abnormal condition detection means for developing a control signal for terminating oscillation operation of said oscillator circuit when an abnormal condition is detected;

said transformer further including an auxiliary winding for developing a voltage proportional to that developed through said secondary winding, said voltage developed through said auxiliary winding being applied to said oscillator circuit for driving said oscillator circuit;

said abnormal condition detection means including an overvoltage detection circuit connected to said auxiliary winding for developing said control signal when an overvoltage is developed through said auxilliary winding;

said overvoltage detection circuit including a latching means for continuously developing said control signal;

said oscillator circuit including an astable multivibrator, and variable impedance means for varying an oscillation frequency of said astable multivibrator.

10. A power supply voltage stabilizer comprising:

a transformer including a primary winding connected to a power source and a secondary winding for output purposes;

switching means connected to said primary winding for controlling power supply to said primary winding;

an oscillator circuit for controlling on/off operation of said switching means;

abnormal condition detection means for developing a control signal for terminating oscillation operation of said oscillator circuit when an abnormal condition is detected;

said transformer further including an auxiliary winding for developing a voltage proportional to that developed through said secondary winding, said voltage developed through said auxiliary winding being applied to said oscillator circuit for driving said oscillator circuit;

said abnormal condition detection means including an overvoltage detection circuit connected to said auxiliary winding for developing said control signal when an overvoltage is developed through said auxiliary winding;

said overvoltage detection circuit including,

a reference voltage generation means for developing a reference voltage proportional to a voltage applied from said power source; and

comparing means for comparing said voltage developed through said auxiliary winding with said reference voltage in order to develop said control signal when said voltage developed through said auxiliary winding exceeds said reference voltage;

said oscillator circuit including an astable multivibrator, and a variable impedance means for varying an oscillation frequency of said astable multivibrator.

11. A power supply voltage stabilizer comprising:

transformer means including a primary winding connected to a power source, a secondary winding for producing an output voltage, and an auxiliary winding for developing a voltage proportional to said output voltage produced by said secondary winding;

switching means connected to said primary winding for controlling the power supply from said power source to said primary winding;

oscillator circuit means for controlling the on/off operation of said switching means;

overvoltage detection circuit means connected to said auxiliary winding for developing a control signal to terminate the oscillation operation of said oscillator circuit means when an overvoltage condition is detected, said overvoltage detection circuit means including,

means for developing a reference potential, and

comparing means responsive to said voltage developed at said auxiliary winding and to said reference potential for comparing said reference potential with said voltage developed at said auxiliary winding and for generating said control signal to terminate the oscillation operation of said oscillator circuit means when said voltage developed at said auxiliary winding exceeds said reference potential.

12. A power supply voltage stabilizer comprising:

transformer means including a primary winding connected to a power source and having a voltage supplied thereto, a secondary winding for producing an output voltage, and an auxiliary winding for developing a voltage proportional to said output voltage produced by said secondary winding;

switching means connected to said primary winding for controlling the power supply from said power source to said primary winding;

oscillator circuit means for controlling the on/off operation of said switching means;

overcurrent detection circuit means connected to said primary winding for developing a control signal to terminate the oscillation operation of said oscillator circuit means when an overcurrent condition is detected, said overcurrent detection circuit means including,

means for monitoring said voltage supplied to said primary winding of said transformer means,

means for measuring the amount of current passing through said primary winding of said transformer means by translating said amount of current into a corresponding amount of voltage potential,

switching means responsive to said corresponding amount of voltage potential for switching to a first switched condition when the corresponding voltage potential exceeds a predetermined voltage potential and for switching to a second switched condition when said voltage potential does not exceed said predetermined voltage potential, and

comparing means responsive to said voltage supplied to said primary winding and connected to an output of said switching means for generating said control signal to terminate oscillation operation of said oscillator circuit means when said switching means switches to said first switched condition in response to the exceeding of said predetermined voltage potential by said corresponding voltage potential.

13. A power supply voltage stabilizer in accordance with claim 11 or 12 wherein said comparing means comprises a double base diode.
Description:

BACKGROUND AND SUMMARY OF THE INVENTION

The present invention relates to a power supply voltage stabilizer and, more particularly, to a power supply voltage stabilizer employing a switching system for controlling power supply to a transformer included in the power supply voltage stabilizer.

In the conventional power supply voltage stabilizer employing a switching system for controlling power supply to a transformer included in the power supply voltage stabilizer, there is a possibility that an abnormal overvoltage will be developed from an output terminal thereof and/or an abnormal overcurrent may flow through the primary winding of the transformer.

Accordingly, an object of the present invention is to provide a protection means for protecting the power supply voltage stabilizer from an abnormal overvoltage and/or overcurrent.

Another object of the present invention is to provide a detection means for detecting an impending overvoltage and/or overcurrent occurring within the power supply voltage stabilizer.

Other objects and further scope of applicability of the present invention will become apparent from the detailed description given hereinafter. It should be understood, however, that the detailed description and specific examples, while indicating preferred embodiments of the invention, are given by way of illustration only, since various changes and modifications within the spirit and scope of the invention will become apparent to those skilled in the art from this detailed description.

The power supply voltage stabilizer of the present invention mainly comprises a transformer including a primary winding connected to a commercial power source through a rectifying circuit, a secondary winding for output purposes, and an auxiliary winding. A driver circuit including a switching means is connected to the primary winding for controlling the power supply to the primary winding. An oscillator circuit is associated with the switching means to control ON/OFF operation of the switching means, thereby controlling the power supply to the primary winding.

To achieve the above objects, pursuant to an embodiment of the present invention, an overvoltage detection circuit is connected to the auxiliary winding. The overvoltage detection circuit functions to compare a voltage created in the auxiliary winding with the rectified power supply voltage, and develop a control signal, when an impending overvoltage is detected, for terminating operation of the oscillator circuit, thereby precluding power supply to the primary winding.

In another embodiment of the present invention, an overcurrent detection circuit is provided for detecting an impending overcurrent flowing through the primary winding to develop a control signal for terminating operation of the oscillator circuit.

BRIEF DESCRIPTION OF THE DRAWINGS

The present invention will become more fully understood from the detailed description given hereinbelow and the accompanying drawings, which are given by way of illustration only, and thus are not limitative of the present invention and wherein:

FIG. 1 is a circuit diagram of a basic construction of a power supply voltage stabilizer of the present invention;

FIG. 2 is a block diagram of an embodiment of a power supply voltage stabilizer of the present invention, which includes an oscillator circuit and an over voltage detection circuit;

FIG. 3 is a circuit diagram of an embodiment of the overvoltage detection circuit included in the power supply voltage stabilizer of FIG. 2;

FIG. 4 is a circuit diagram of an embodiment of the oscillator circuit included in the power supply voltage stabilizer of FIG. 2;

FIG. 5 is a waveform chart for explaining operation of the oscillator circuit of FIG. 4;

FIG. 6 is a block diagram of another embodiment of a power supply voltage stabilizer of the present invention, which includes an oscillator circuit and an overcurrent detection circuit; and

FIG. 7 is a circuit diagram of an embodiment of the overcurrent detection circuit included in the power supply voltage stabilizer of FIG. 6.

DESCRIPTION OF THE PREFERRED EMBODIMENTS

Referring now in detail to the drawings, and to facilitate a more complete understanding of the present invention, a basic construction of a power supply voltage stabilizer of the present invention will be first described with reference to FIG. 1.

The power supply voltage stabillizer mainly comprises a transformer T including a primary winding N 1 connected to a commercial power source V, a secondary winding N 2 connected to an output terminal V 0 , and an auxiliary winding N 3 . An oscillator circuit OSC is associated with the primary winding N 1 and the auxiliary winding N 3 to control the power supply from the commercial power source V to the primary winding N 1 .

A rectifying circuit E is connected to the commercial power source V for applying a rectified voltage to a capacitor C 1 . A negative terminal of the capacitor C 1 is grounded, and a positive terminal of the capacitor C 1 is connected to the collector electrode of a switching transistor Q 5 through the primary winding N 1 of the transformer T. The oscillator circuit OSC performs the oscillating operation when receiving a predetermined voltage, and develops a control signal toward the base electrode of the switching transistor Q 5 to control the switching operation of the switching transistor Q 5 . The switching transistor Q 5 functions to control the power supply to the primary winding N 1 , thereby controlling the power transfer to the secondary winding N 2 and the auxiliary winding N 3 .

The auxiliary winding N 3 is connected to a capacitor C 3 in a parallel fashion via a diode D 1 . A positive terminal of the capacitor C 3 is connected to the oscillator circuit OSC to supply a drive voltage Vc 3 . A negative terminal of the capacitor C 3 is connected to the emitter electrode of the switching transistor Q 5 and grounded. The positive terminal of the capacitor C 3 is connected to the primary winding N 1 via a diode D 2 and a capacitor C 2 in order to stabilize the initial condition of the oscillator circuit OSC.

The secondary winding N 2 functions to develop a predetermined voltage through the output terminal V 0 . A smoothing capacitor C 0 is connected to the secondary winding N 2 via a diode D 0 , and a series circuit of a resistor R 0 and a light emitting diode D i is connected to the smoothing capacitor C 0 in a parallel fashion. The light emitted from the light emitting diode D i is applied to a photo transistor Q 8 employed in the oscillator circuit OSC. The light emitting diode D i and the photo transistor Q 8 are preferably incorporated in a single package as a photo coupler.

The light amount emitted from the light emitting diode D i is proportional to the output voltage developed from the output terminal V 0 . The photo transistor Q 8 exhibits the impedance corresponding to the applied light amount. The oscillator circuit OSC is so constructed that the oscillation frequency is varied in response to variation of the impedance of the photo transistor Q 8 . Accordingly, the ON/OFF operation of the switching transistor Q 5 is controlled in response to the output voltage level, thereby stabilizing the output voltage level.

In the above constructed power supply voltage stabilizer, there is a possibility that an abnormal overvoltage is developed through the secondary winding N 2 and the auxiliary winding N 3 when the oscillator circuit OSC or the light emitting diode D i is placed in the fault condition.

FIG. 2 shows an embodiment of the power supply voltage stabilizer of the present invention, which includes means for precluding occurrence of the above-mentioned overvoltage. Like elements corresponding to those of FIG. 1 are indicated by like numerals.

The power supply voltage stabilizer of FIG. 2 mainly comprises the transformer T, the oscillator circuit OSC, a driver circuit 1 including the switching transistor Q 5 , and an overvoltage detection circuit 3.

The positive terminal of the capacitor C 3 is connected to the driver circuit 1 and the oscillator circuit OSC to apply the driving voltage thereto. The positive terminal of the capacitor C 3 is also connected to the primary winding N 1 through the diode D 2 and a parallel circuit of the capacitor C 2 and a resistor R 2 in order to stabilize the initial start operation of the oscillator circuit OSC. The secondary winding N 2 is connected to an output level detector 2, which comprises the light emitting diode D i as shown in FIG. 1. The ON/OFF control of the switching transistor Q 5 is similar to that is achieved in the power supply voltage stabilizer of FIG. 1.

The secondary winding N 2 and the auxiliary winding N 3 are wound in the same polarity fashion and, therefore, the voltage generated through the auxiliary winding N 3 is proportional to that voltage generated through the secondary winding N 2 . The overvoltage detection circuit 3 is connected to receive the voltage at a point a as a power source voltage, and the voltage at a point b which is connected to the positive terminal of the capacitor C 3 . When the voltage level at the point b exceeds a reference level, the overvoltage detection circuit 3 develops a control signal for terminating the operation of the oscillator circuit OSC.

FIG. 3 shows a typical construction of the overvoltage detection circuit 3.

The voltage at the point a is applied to a series circuit of resistors R 3 and R 4 , and grounded. The voltage at the point b is applied to the connection point of the resistors R 3 and R 4 via a diode D 3 . The connection point of the resistors R 3 and R 4 is grounded through resistors R 5 and R 6 and a Zener diode Z 1 . A double-base diode (Trade Name Programmable Unijunction Transistor) P 1 is provided for developing the control signal to be applied to the oscillator circuit OSC. The anode electrode of the programmable unijunction transistor P 1 is connected to the connection point of the resistors R 3 and R 4 , the gate electrode of the programmable unijunction transistor P 1 is connected to the connection point of the resistors R 5 and R 6 , and the cathode electrode is connected to the oscillator circuit OSC.

When the voltage level of the point b exceeds a reference level VZ 1 , the programmable unijunction transistor P 1 is turned on to develop the control signal for terminating the oscillation operation of the oscillator OSC. In this way, the impending abnormal overvoltage is detected to protect the circuit elements. The ON condition of the programmable unijunction transistor P 1 is maintained as long as the main power switch is closed, because the overvoltage detection circuit 3 is connected to receive the voltage from the point a.

The voltage detection circuit 3 does not necessarily employ the programmable unijunction transistor. Another element showing the latching characteristics such as a negative resistance element can be employed instead of the programmable unijunction transistor.

FIG. 4 shows a typical construction of the oscillator circuit OSC.

The oscillation circuit OSC mainly comprises an astable multivibrator including transistors Q 1 , Q 2 and Q 3 , and an output stage including a transistor Q 4 . The astable multivibrator is connected to receive the voltage appearing across the capacitor C 3 , and develops an output signal of which frequency is determined by the circuit condition as long as the multivibrator receives a voltage greater than a predetermined level.

The output signal of the output stage is applied to the base electrode of the switching transistor Q 5 included in the driver circuit 1 in order to switch the switching transistor Q 5 with a predetermined frequency. A transistor Q 9 is interposed between the base electrode of the transistor Q 3 and the grounded terminal. The transistor Q 9 is controlled by the control signal derived from the overvoltage detection circuit 3. Accordingly, the transistor Q 3 is turned off to terminate the oscillation operation when the abnormal overvoltage is detected by the overvoltage detection circuit 3.

Now assume that a voltage Vc 3 is developed across the capacitor C 3 . When main power supply switch is closed, the voltage Vc 3 varies in a manner shown by a curve X in FIG. 5. When the voltage Vc 3 reaches a predetermined level, the astable multivibrator begins the oscillation operation. More specifically, the transistor Q 1 is first turned on because the base electrode of the transistor Q 1 is connected to a capacitor C 4 of which the capacitance value is relatively small. At this moment, the transistor Q 2 is held off.

Because of turning on of the transistor Q 1 , the capacitor C 4 is gradually charged through a resistor R 4 and the transistor Q 1 . Accordingly, the base electrode voltage of the transistor Q 1 is gradually increased and, hence, the emitter electrode voltage of the transistor Q 1 is also increased to turn on the transistor Q 2 . When the transistor Q 2 is turned on, the transistor Q 3 is also turned on. The base electrode voltage of the transistor Q 2 which is bypassed by a resistor R 1 is reduced and, therefore, the transistor Q 2 is stably on. At this moment, the transistor Q 1 is turned off.

When the transistor Q 3 is turned on, the transistor Q 4 is turned on to develop a signal to turn on the switching transistor Q 5 . Upon turning on of the transistor Q 3 , the charge stored in the capacitor C 4 is gradually discharged through paths shown by arrows in FIG. 4. Therefore, the base electrode voltage of the transistor Q 1 is gradually reduced. When the base electrode voltage of the transistor Q 1 becomes less than a predetermined level, the transistor Q 1 is turned on, and the transistor Q 2 , Q 3 and Q 4 are turned off. Accordingly, the transistor Q 5 is turned off. After passing the initial start condition, the driving voltage Vc 3 is held at a predetermined level as shown by a curve Y in FIG. 5 to maintain the above-mentioned oscillation operation.

The photo transistor Q 8 is disposed in the discharge path of the capacitor C 4 in order to control the discharge period in response to the impedance of the photo transistor Q 8 . That is, the oscillation frequency is controlled in response to the light amount emitted from the light emitting diode included in the output level detector 2.

FIG. 6 shows another embodiment of the power supply voltage stabilizer of the present invention, which includes means for precluding occurrence of an abnormal overcurrent. Like elements corresponding to those of FIG. 2 are indicated by like numerals.

In the power supply voltage stabilizer of FIG. 1, there is a possibility that an abnormally large current flows through the primary winding N 1 when the magnetic flux is saturated due to requirement of large current at the secondary winding side. The power supply voltage stabilizer of FIG. 6 includes an overcurrent detection circuit 4 for detecting an impending abnormally large current.

A resistor R 9 is interposed between the emitter electrode of the switching transistor Q 5 included in the driver circuit 1 and the grounded terminal. The overcurrent detection circuit 4 is connected to receive a signal from the connection point of the resistor R 9 and the emitter electrode of the switching transistor Q 5 , thereby developing a control signal for terminating the oscillation operation of the oscillation circuit OSC.

FIG. 7 shows a typical construction of the overcurrent detection circuit 4.

The voltage at the point a is applied to a series circuit of resistors R 10 and R 11 , and grounded. The collector electrode of a transistor Q 10 is connected to the connection point of the resistors R 10 and R 11 through resistors R 12 and R 13 . The emitter electrode of the transistor Q 10 is grounded. The base electrode of the transistor Q 10 is connected to the connection point of the resistor R 9 and the emitter electrode of the switching transistor Q 5 via a resistor R 14 .

When the switching transistor Q 5 is turned on, a current flows through the resistor R 9 . When the voltage drop across the resistor R 9 exceeds a predetermined value due to a large current, the transistor Q 10 is turned on to turn on the programmable unijunction transistor P 1 . That is, when a large current flows through the primary winding N 1 , the programmable unijunction transistor P 1 develops the control signal to terminate the oscillation operation of the oscillator circuit OSC.

The invention being thus described, it will be obvious that the same may be varied in many ways. Such variations are not to be regarded as a departure from the spirit and scope of the invention, and all such modifications are intended to be included within the scope of the following claims.

CGE CT 8826 TV 26" TELECOLOR  (TELEFUNKEN)  CHASSIS 712A   UNITS: 
 
CHASSIS 712A SUPPLY UNIT (NETZTEIL SM) AT 349354065 This is a SMPS Supply unit which seems simple but is not ! - 3 SUB Units are composing the FINAL device unit 1 
- MAINS RECTIFIER + DEGAUSS PTC + BOBBIN FILTERS + CAPS (burned !! !!!) BS422 ET 309378996 (NETZEINGANG) 2 
- Pulse Command unit with S417T (Telefunken) BS423 AT349354067 (ANSTEUERUNG) 3 
- Secondary Voltages Generation and separation (With a LM317) BS426 AT349354068 (SEC.SPANNUNGSERZEUGUNG). 
 
- CHROMA IA (1) with TDA2150 (Telefunken) BS202 AT349354052
 - CHROMA II (2) with TDA2160 + TDA2140 (Telefunken) BS302
 - Synchronization BS531 AT349354014 with ITT TBA950X2 
- Frame Oscillator BS451 AT349354015
 - Frame deflection output amplifier BS491 AT349354016 with BD312T + 2N5877T (Motorola + Fairchild)
 - E/W Correction unit BS501 AT349354017 
- RGB ENDSTUFEN RGB OUT BS333 AT349354063 
- TON ENDSTUFE SOUND UNIT BS151 AT349354008 
 - if video unit BS104 AT349 354 105. Search and Tuning drive circuitry
. - BS33 (UAA170 Siemens + UA741 Texas Instruments + CD4011 RCA) Display search 
 - SPP core unit with AY-3-8203 (General Instruments) + MSM4956 (General Instruments) + ER1400 EAROM (General Instruments)
 - RECEIVER 5000 With U318M (Telefunken) BS48 AT349370969. 
 
 
CGE CT 8826 TV 26" TELECOLOR  (TELEFUNKEN)  CHASSIS 712A   TELEFUNKEN CHASSIS 712 Drive circuit for an infrared remote control transmitter: An infrared remote control transmitter includes at least one infrared light-emitting diode poled with respect to a point of reference potential so as to be conductive in response to voltages having the opposite polarity of a DC supply voltage and to be nonconductive in response to voltages having the same polarity as the DC supply voltage. A push-pull amplifier is responsive to a pulse signal encoded to represent a remote control message to selectively couple the DC supply voltage or the reference potential to a capacitor coupled in series between the push-pull amplifier and the light-emitting diode. The capacitor is charged and discharged and an alternating drive voltage for the light-emitting diode having portions with polarities both the same as and opposite to the polarity of the DC supply voltage is generated. The push-pull amplifier is arranged so that when a component failure occurs, the portions of the alternating drive voltage having the polarity opposite to the polarity of the DC supply voltage are at least inhibited to prevent the continuous (i.e., DC) emission of infrared radiation. 1. In an infrared remote control transmitter for controlling a television system, apparatus comprising:

a reference circuit point for receiving a reference potential;

a supply circuit point for receiving a DC supply voltage;

a battery connected with a predetermined polarity connected between said supply and reference circuit points;

at least one light-emitting diode for emitting infrared radiation when rendered conductive, said light emitting diode having a cathode and an anode, one of said cathode and anode being connected to said reference circuit point, said light-emitting diode being poled with respect to said reference circuit point so as to be conductive in response to the application of a voltage to the other one of said cathode and anode having the opposite polarity to said battery with respect to said reference circuit point and non-conductive in response to the application of a voltage to said other one of said cathode and anode having the same polarity as said battery with respect to said reference circuit point;

a source cir

cuit point for receiving an input signal having pulses encoded to represent information for controlling a predetermined function of said television receiver;

a drive circuit point;

a capacitor directly connected between said drive circuit point and said other one of said cathode and anode;

a diode directly connected between said other one of said cathode and anode and said reference circuit point and poled in the opposite sense to said light-emitting diode with respect to said reference circuit point;

push-pull amplifier means for developing a drive voltage at said drive point including first and second bipolar transistors of opposite conduction types, each of said transistors having a collector-emitter path and a base electrode for controlling the conduction of said collector-emitter path, said collector-emitter path of said first transistor being directly connected between said supply circuit point and said drive circuit point, said collector-emitter path of said second transistor being connected between said drive circuit point and said reference point; and

input means coupled between said source circuit point and said bases of said first and second transistors for rendering said collector-emitter path of said first transistor conductive and said collector-emitter path of said second transistor non-conductive in response to a first portion of said pulses of said input signal and for rendering said collector-emitter path of said second transistor conductive and said collector-emitter path of said first transistor non-conductive in response to a second portion of said pulses of said input signal.

2. The apparatus recited in claim 1 wherein:

three light-emitting diodes poled in the same direction are connected in series between said capacitor means and said reference circuit point.

3. The apparatus recited in claim 1 wherein:

a second capacitor is directly connected between said drive point and said other one of said cathode and anode in parallel with said first mentioned capacitor directly connected between said drive point and said other one of said cathode and anode.

4. The apparatus recited in claim 1 wherein:

said input means includes a first capacitor connected between said source circuit point and said base of said first transistor; first means connected between said supply circuit point and said base of said first transistor for discharging said first capacitor; a second capacitor connected between said source circuit point and said base of said second transistor; and second means connected between said base of said second transistor and said reference circuit point for discharging said second capacitor.

5. The apparatus recited in claim 4 wherein:

said first means includes a further diode poled to be conductive when said collector-emitter path of said first transistor is non-conductive and non-conductive when said collector-emitter path of said first transistor is conductive; and

said second means includes a still further diode poled to be conductive when said collector-emitter path of said second transistor is non-conductive and non-conductive when said collector-emitter path of said second transistor is conductive.

6. In an infrared remote control transmitter for controlling a television system, apparatus comprising:

a reference circuit point for receiving a reference potential;

a supply circuit point for receiving a DC supply voltage;

a battery connected with a predetermined polarity connected between said supply and reference circuit points;

three light-emitting diodes which emit infrared radiation when rendered conductive directly connected in series between a voltage application circuit point and said reference circuit point, all of said light-emitting diodes being poled with respect to said reference circuit point so as to be conductive in response to the application of a voltage to said voltage application circuit point having the opposite polarity to said battery with respect to said reference circuit point and non-conductive in response to the application of a voltage to said voltage application circuit point having the same polarity as said battery with respect to said reference circuit point;

a source circuit point for receiving an input signal having pulses encoded to represent information for controlling a predetermined function of said television receiver;

a drive circuit point;

a first capacitor directly connected between said drive circuit point and said voltage application circuit point;

a second capacitor directly connected between said drive circuit point and said voltage application circuit point;

a diode directly connected between said voltage application circuit point and said reference circuit point and poled in the opposite sense to said light-emitting diode with respect to said reference circuit point;

push-pull amplifier means for developing a drive voltage at said drive point including first and second bipolar transistors of opposite conduction types, each of said transistors having a collector-emitter path and a base electrode for controlling the conduction of said collector-emitter path, said collector-emitter path of said first transistor being directly connected between said supply circuit point and said drive circuit point, said collector-emitter path of said second transistor being connected between said drive circuit point and said reference point; and

input means coupled between said source circuit point and said bases of said first and second transistors for rendering said collector-emitter path of said first transistor conductive and said collector-emitter path of said second transistor non-conductive in response to a first portion of said pulses of said input signal and for rendering said collector-emitter path of said second transistor conductive and said collector-emitter path of said first transistor non-conductive in response to a second portion of said pulses of said input signal.

Description:

BACKGROUND OF THE PRESENT INVENTION

The present invention relates to drive circuits for infrared remote control transmitters.

Infrared remote control systems for television receivers and the like are known. The chief advantage of infrared remote control systems in comparison to ultrasonic remote control systems is that they are less susceptible to erroneously-generated interference signals. Unfortunately, the human eye may be harmed under conditions of prolonged, continuous and direct exposure to infrared radiation.

In order to reduce the possibility of harm to the eyes of users, infrared remote control systems utilize special pulse codes which minimize the duration of infrared radiation during the transmission of remote controlled messages. However, since in conventional drive circuits for infrared remote control transmitters the infrared light source, e.g., a light-emitting diode or diodes, is typically included in a direct current path from a supply voltage, infrared radiation may be continuously emitted should there be a component failure in the remote control transmitter. Therefore, there is a requirement for drive circuits for use in infrared remote control transmitters in which component failures do not result in the continuous emission of infrared radiation. The present invention concerns such a "fail-safe" drive circuit.

SUMMARY OF THE PRESENT INVENTION

In a remote control transmitter, at least one infrared light-emitting diode is coupled to a point of reference potential and poled so as to be substantially nonconductive in response to voltages having the same polarity as a DC supply voltage for the transmitter and substantially conductive in response to voltages having the polarity opposite to the polarity of the DC supply voltage. Driver means responsive to an input signal is coupled between the source of the DC supply voltage and the light-emitting diode. The driver means normally generates an alternating drive voltage for the light-emitting diode having portions with polarities both the same as and opposite to the polarity of the DC supply voltage. The driver means is arranged so that the portions of the drive signal having the polarity opposite to that of the DC supply voltage are at least inhibited when a component failure occurs.

BRIEF DESCRIPTION OF THE DRAWING

The sole FIGURE of the drawing shows, partially in block diagram form and partially in schematic diagram form, an infrared remote control system constructed in accordance with the present invention as it may be employed in a television receiver arrangement.

DETAILED DESCRIPTION OF THE DRAWING

A television receiver 1 includes an antenna 3, a tuner 5, an IF signal processing unit 7, a picture signal processing unit 9, a sound signal processing unit 11, a picture tube 13 and a speaker 15 arranged in a conventional fashion to produce visual and audio responses. A power supply 17 is selectively energized to generate DC supply voltages for the portions of the receiver so far described from the AC line voltage in response to an ON/OFF control signal generated by a remote control receiver 19. Receiver 1 also includes a standby power supply 20 which continuously couples a DC supply voltage to remote control receiver 19 so that it is ready to accept messages from a remote control transmitter 21.

Remote control receiver 19 includes a photosensitive diode 23. The conduction of photo diode 23 is controlled in response to encoded optical signals having frequencies in the infrared range generated by remote control transmitter 21. A detector 25 senses the changes in the conduction of diode 23 and generates electrical signals corresponding to the encoded optical signals. The electrical signals are decoded by a decoder 27 to generate the ON/OFF control signal for tuning receiver 1 on and off, a CHANNEL SELECTION control signal for controlling the frequency to which a tuner 5 is tuned, and a VOLUME control signal for controlling the sound level of receiver 1.

Remote control transmitter 21 includes a keyboard 29 including push buttons (not shown) by which a user may control the various receiver functions enumerated above. When a push button is depressed a corresponding electrical signal is generated by keyboard 29. A pulse encoder 31 is responsive to these electrical signals to generate respective coded pulse signals. The coded pulse signals are processed by a driver 33 to cause infrared light-emitting diodes 35, 37 and 39 to generate corresponding optical signals in the infrared frequency range.

Various codes for infrared remote control systems and encoders and decoders for these codes are known. For example, encoder 31 and decoder 27 may comprise S2600 and S2601 integrated circuits manufactured by American Microsystems, Inc. of Santa Clara, Calif.

The exact nature of the codes is not directly germane to the present invention. However, it is desirable for the reasons of safety discussed earlier that the code formats are arranged so that the duration of infrared radiation during a transmission is minimized. Since the pulses of the pulse signals generated by pulse encoder 31 correspond to the intervals of infrared radiation, this may be accomplished by causing the electrical pulse signals generated by encoder 31 to have a relatively low duty cycle, e.g., less than 20 percent. In addition, for safety reasons, it is desirable that light-emitting diodes 35, 37 and 39 be physically separated on transmitter 21 from one another by a distance selected so that the power of the infrared radiation they generate is distributed rather than concentrated in a relatively small area.

While these safety precautions to some extent minimize the danger to users, they do not account for component failures which may cause the continuous, i.e., DC, emission of infrared radiation. Unfortunately, the human eye may be injured when directly exposed to continuous infrared radiation for prolonged periods. While such situations are extremely rare, since they would involve not only a component failure but the misuse of the transmitter, they may occur under extraordinary circumstances. For example, a curious child may point an infrared transmitter with a failed component directly into his eye.

Drive circuit 33 is arranged to prevent the continuous emission of infrared radiation under any foreseeable component failure mode. Driver 33 includes a push-pull amplifier 41 comprising a PNP transistor 43 and an NPN transistor 45 having their collector-emitter junctions coupled in series between a battery 47 and signal ground. Battery 47 is the source of DC supply voltage for transmitter 21. The output of pulse encoder 31 is coupled to the bases of transistors 43 and 45 through capacitors 49 and 51, respectively. Diodes 53 and 55 are coupled in shunt with the base-emitter junctions of transistors 43 and 45, respectively. The junction of the collectors of transistors 43 and 45 is coupled through parallel connected capacitors 57 and 58 to the cathode of light-emitting diode 35. Light-emitting diodes 35, 37 and 39 are connected in series with the same polarity between capacitors 57 and 58 and signal ground. The polarity of light-emitting diodes 35, 37 and 39 is selected so that they are rendered nonconductive in response to the application of voltages to the cathode of light-emitting diode 35 having the same polarity (i.e., positive) with respect to signal ground as the DC supply voltage provided by battery 47 and only rendered conductive in response to the application of voltages having the opposite polarity (i.e., negative) with respect to signal ground to the DC supply voltage. A diode 59 is connected in shunt with series connected light-emitting diodes 35, 37 and 39 and poled in the opposite direction.

In operation, pulse encoder 31 generates a pulse signal encoded as described above. The pulse signal includes positive-going pulses. In response to the leading edges of the positive-going pulses, transistor 45 is rendered conductive. In response to the trailing edges of the positive-going pulses, transistor 43 is rendered conductive. Diodes 53 and 55 serve as discharge paths for capacitors 49 and 51 during the intervals when transistors 43 and 45, respectively, are nonconductive. Diodes 53 and 55 also clamp the voltage at the bases of transistors 43 and 45 close to the battery voltage and the voltage at signal ground, respectively, in order to protect the base-emitter junctions of transistors 43 and 45 from reverse breakdown failure voltages. Desirably, capacitors 49 and 51 have relatively small values so that capacitors 49 and 51 are charged and discharged in response to each pulse. As a result, transistors 43 and 45 are alternately rendered conductive and nonconductive in response to each pulse of the pulse signal.

When transistor 43 is conductive (and transistor 45 is nonconductive) capacitors 57 and 58 are charged from battery 47. When transistor 45 is conductive (and transistor 43 is nonconductive) capacitors 57 and 58 are discharged to signal ground. As a result, an alternating drive voltage, i.e., one having polarity excursions above and below the potential at signal ground, are generated at the cathode of light-emitting diode 35. Light-emitting diodes are conductive in response to the negative portions of the drive voltage and are nonconductive in response to the positive portions of the drive voltage. Diodes 35, 37 and 39 only emit infrared radiation when they are conductive. Therefore, infrared radiation is only emitted by transmitter 21 when the drive voltage has a polarity (i.e., negative opposite to the polarity of the DC supply voltage.

Desirably, the capacitance of the combination of capacitors 57 and 58 is relatively large, e.g., 1 microfarad, so that sufficient drive current is provided to light-emitting diodes 35, 37 and 39 to cause them to emit infrared radiation. For the same reason, two capacitors rather than one are used, since the effective series resistance associated with the parallel combination is smaller than the series resistance of a single capacitor.

In the event that there is a component failure within drive circuit 33, drive voltage developed at the cathode of light-emitting diode 35 will be reduced and, in most cases, substantially inhibited. Under these conditions, since the amplitude of the negative portions of the drive signal will at least have a lower than normal amplitude, the infrared radiation will have a lower than normal energy.

Briefly, any failure of a component within driver 33 causing the component to open or short, substantially prevents the development of an alternating drive signal at the cathode of light-emitting diode 35. Since diodes 35, 37 and 39 are rendered conductive only in response to negative-going voltages, no infrared radiation is generated. Any component failure between the extremes of an open or short causes a reduction in the amplitude of the alternating drive signal. By way of example, consider the following failure modes. If either transistor 43 or 45 fails, e.g., by shorting from collector to emitter, capacitors 57 and 58 will be either permanently charged or discharged, thereby preventing the development of an alternating drive signal. If one of capacitors 57 and 58 shorts, only positive-going voltages are developed at the cathode of light-emitting diode 35. If the collector to emitter junction of transistor 43 and one of capacitors 57 and 58 short, a DC signal is coupled to the cathode of light-emitting diode 35, thereby rendering diode 59 conductive and preventing light-emitting diodes 35, 37 and 39 from being rendered conductive. If diode 59 opens, capacitors 57 and 58 will not be charged thereby preventing the development of an alternating voltage at the cathode of diode 35. If diode 59 fails so as to lose its unidirectional conductive characteristics, i.e., in essence becomes a passive element, an alternating drive signal will be developed but it will have a lower than normal amplitude. Furthermore, failures in pulse encoder 31 causing generation of a DC signal rather than a pulse signal will also cause the loss of an alternating drive signal.

Driver circuit 33 may be modified in some respects without causing the loss of its "fail-safe" nature. For example, any or all of diodes 53, 55 and 59 may be replaced with resistors. While this modification causes a reduction in efficiency of the normal operation of drive circuit 33, it does not alter its "fail-safe" nature. These and other modifications are intended to be within the scope of the present invention as set forth in the following claims.

TELEFUNKEN CHASSIS 712A Tuning circuit arrangement

A tuning circuit arrangement comprises one or more tuned circuits whose frequency range is tuned by tuning diodes, means being provided for varying the tuning voltage of the tuning diodes to provide exclusive variation of the tuned circuit capacitance of the tuned circuit. 1. A circuit for adjusting a tuning circuit, the tuning circuit including at least one resonant circuit composed of a variable inductance and a variable capacitance constituted by at least one voltage-variable tuning diode, one side of the resonant circuit being connected to a point at circuit ground potential and adjustment of the resonant circuit being effected by changing the resonant circuit inductance and the resonant circuit capacitance, with changing of the resonant circuit capacitance being effected exclusively by varying the tuning voltage of the tuning diode, the tuning circuit further including a source of a variable tuning potential which is variable over a range between maximum and minimum extreme values, each extreme value being different from the circuit ground potential, and said circuit for adjusting comprising at least one adjustment potentiometer connected between a point of said source providing the variable tuning potential and a point of said source permanently providing one of said extreme values, said potentiometer having an adjustable tap connected to provide the tuning voltage for said tuning diode. 2. An arrangement as defined in claim 1 wherein said tuning circuit includes a plurality of said resonant circuits and said circuit for adjusting comprises a plurality of said potentiometers connected together in parallel and each having a respective adjustable tap connected to provide the tuning voltage for at least one respective tuning diode. 3. An arrangement as defined in claim 1 wherein said source comprises a tuning potentiometer connected to have a respective one of the extreme values of the tuning potential at each of its ends and having an adjustable tap providing the variable tuning potential, and said adjustment potentiometer is connected between one end and said movable tap of said tuning potentiometer. 4. An arrangement as defined in claim 1 wherein said tuning circuit includes at least two of said resonant circuits and said adjustable tap of said adjustment potentiometer is connected to provide the tuning voltage for said at least two resonant circuits. 5. An arrangement as defined in claim 4 wherein said resonant circuits have respectively different relative frequency variations.
Description:

BACKGROUND OF THE INVENTION

The invention relates to a tuning circuit arrangement comprising one or more tuning circuits in which tuning diodes are provided for tuning of the frequency range. In such an arrangement, the adjustment of the tuned circuit takes place, for example, by changing the tuned circuit inductance and the tuned circuit capacitance.

As is known, tuning circuits have the object of tuning the resonant circuits of selective amplifiers and/or oscillators to a given resonant frequency. In a known tuning circuit, the adjustment to synchronous operation in each circuit takes place via a tuning coil and a particular trimmer capacitor. In the known tuning circuit arrangement a multiply repeated adjustment of the inductance and the capacitance is required for adjustment to synchronous operation, because the setting of the trimmer capacitors again changes the resonant frequency of the frequency previously set inductively.

SUMMARY OF THE INVENTION

It is an object of the invention to provide a tuning circuit arrangement with simplified adjustment.

According to a first aspect of the invention, there is provided a tuning circuit arrangement comprising one or more tuned circuits, tuning diodes in said tuned circuits for tuning the frequency range of said tuned circuits and means for varying the tuning voltage of said tuning diodes for providing exclusive variation of the tuned circuit capacitance of said tuned circuit.

According to a second aspect of the invention, there is provided a tuning circuit arrangement comprising one or more tuning circuits, in which tuning diodes are provided for the purpose of tuning the frequency range and in which the tuned circuit adjustment takes place by changing the tuned circuit inductance and the tuned circuit capacitance, characterized in that the adjustment in capacitance takes place exclusively by varying the tuning voltage for the tuning diode(s).

BRIEF DESCRIPTION OF THE DRAWINGS

The invention will now be described in greater detail, by way of example, with reference to the drawings in which:

FIG. 1 is a circuit diagram showing a first form of circuit arrangement in accordance with the invention as applied to two resonant circuits;

FIG. 2 is a circuit diagram similar to FIG. 1 but showing the arrangement applied to n resonant circuits;

FIG. 3 is a circuit diagram similar to FIG. 1 but showing the arrangement with a different form of adjustment;

FIG. 4 is a circuit diagram similar to FIG. 2 in which the arrangement of FIG. 3 is applied to n resonant circuits;

FIG. 5 is a circuit diagram showing a part of the arrangement showing a different form of adjusting circuitry;

FIG. 6 is a circuit diagram similar to FIG. 5 but showing a still further form of adjusting circuitry;

FIG. 7 is a block diagram of part of the arrangement provided with temperature compensation and,

FIG. 8 is a block diagram similar to FIG. 7 but including a decoupling circuit.

DESCRIPTION OF THE PREFERRED EMBODIMENTS

In a tuning circuit arrangement of the type mentioned at the beginning it is proposed in accordance with the invention and in order to solve the object that the adjustment in capacitance should take place exclusively by variation of the tuning voltage for the tuning diode(s).

The essence of the invention on the one hand consists in that special trimmer capacitors for achieving an adjustment in capacitance are omitted and that the adjustment in capacitance takes place exclusively by variations of the tuning voltage for the tuning diode(s) which is in contrast to the known method, and does not take place by means of trimmer capacitors. On the other hand, the invention does not require any repetitive adjustment of the tuned circuits of the tuning circuits.

The tuning circuit arrangement in accordance with the invention makes it possible to reduce considerably the required maximum tuning voltage. With the tuning circuit arrangement in accordance with the invention it is possible to operate with small tuning voltages even when using tuning diodes having abrupt pn junction. The sought after simplification of the adjustment can be achieved by means of the fact that the capacitative adjustment does not influence the previously operated adjustment in inductance.

In the tuning circuit arrangement according to the invention potentiometers, for example, are provided in order to adjust the capacitance. There is the possibility of using the same adjusting means for adjusting the capacitance of two or more tuned circuits. Similarly, the same adjustment means may serve to adjust the capacitance of several tuned circuits having varying relative frequency variation.

In accordance with a further refinement of the invention a circuit arrangement for producing minimum and maximum tuning potentials is provided which is constructed so that the potentials produced by it have such a temperature dependence that the effect of temperature on the tuning circuit is compensated.

It is advisable to connect a decoupling circuit between the means for adjusting capacitance and the 6 tuning potentiometers, the decoupling circuit reducing the electrical load on the tuning potentiometer through the adjustment means. In accordance with an embodiment of the invention, precautions are taken to ensure that one of the two potentials applied to an adjustment potentiometer, does not change during adjustment.

The adjustment potentiometer or potentiometers are connected for example between a point in the circuit at which the variable tuning potential is available and a point in the circuit at which the minimum tuning potential is available. There is also the possibility of connecting the adjustment potentiometer or potentiometers between a point in the circuit at which the variable tuning potential is available and a point in the circuit at which the maximum tuning potential is available.

Referring now to the drawings, FIG. 1 shows an electronic tuning circuit in accordance with the invention which operates with tuning diodes. The tuning circuit of FIG. 1, which is for example a component of a VHF tuner, consists of two variable-frequency resonant circuits and in fact an oscillator circuit 1 and a resonant circuit 2 for selecting the input signal. The oscillator circuit comprises an inductance 3 and a tuning diode 4, which is a double diode in this embodiment. The resonant circuit 2 comprises an inductance 5 and a tuning diode 6, which in this embodiment is also a double diode. As may be seen from FIG. 1, neither of the two resonant circuits 1 and 2 has a trimmer capacitor. Of course, parallel to the resonant circuits there are unavoidable circuit capacitances 7 and 8 which are shown in broken lines.

The two resonant circuits 1 and 2 must be adjusted to achieve synchronous operation. In accordance with the invention the adjustment potentiometers 9 and 10 are provided for this purpose. The adjustment potentiometers 9 and 10 are connected in parallel with one another in the embodiment of FIG. 1. Two limiting potentials are required for the tuning circuit; in fact the largest potential U max at point 11 and the smallest potential U min at point 12. In the embodiment of FIG. 1 the two adjustment potentiometers 9 and 10 lie between the wiper contact 13 of the tuning potentiometer 14 and the point 12 having the potential U min . The tuning potentiometer 14 lies between the points 11 and 12, i.e. between the maximum potential U max and the minimum potential U min . The maximum tuning potential U max and the minimum tuning potential U min are in fact linked together, yet they are produced in a separate circuit arrangement. This is indicated symbolically in FIG. 1 by means of the two voltage sources 23 and 24. The minimum tuning potential U min is therefore not derived via a purely ohmic voltage divider from the maximum tuning potential U max .

In the tuning circuit of FIG. 1, in the case where the tuning potentiometer 14 is set to the minimum tuning voltage, the voltages taken from the adjustment potentiometers 9 and 10 are not influenced by the settings of the adjustment potentiometer. Therefore, if the wiper contact 13 of the tuning potentiometer 14 is located at the lowest position then no matter how the adjustment potentiometers 9 and 10 are rotated the adjustment voltages for the tuning diodes will not be influenced by this. This has the consequence that setting in the upper frequency range has no influence on the previously set lower frequency. The adjustment of the lower frequency is only dependent on the inductance adjustment of the inductances 3 and 5.

The tuning circuit of FIG. 2 is distinguished from the tuning circuit of FIG. 1 by the fact that instead of only two resonant circuits n resonant circuits are provided and, instead of only two adjustment potentiometers, m adjustment potentiometers are provided. m may be smaller than n if not merely one resonant circuit but more than one resonant circuit is adjusted by means of a single adjustment potentiometer.

FIG. 3 shows an embodiment of the invention in which in contrast to FIGS. 1 and 2 the adjustment potentiometers 9 and 10 lie between the wiper contact 13 of the tuning potentiometer 14 and point 11 having the potential U max . In this case, the adjustment in inductance takes place in the upper frequency and the adjustment in capacitance takes place in the lower frequency by means of the adjustment potentiometers 9 and 10.

The tuning circuit of FIG. 4 is distinguished from the tuning circuit of FIG. 3 by the fact that, instead of only two resonant circuits, again n resonant circuits are provided and instead of only two adjustment potentiometers m adjustment potentiometers are provided.

According to FIG. 5 the adjustment in capacitance is undertaken for the upper frequency by setting the maximum tuning potential. While in the tuning circuits of FIGS. 1 to 4 the adjustment of the individual tuned circuits is independent, in the arrangement of FIG. 5 the setting of the maximum tuning potential effects all tuned circuits. The setting of the maximum tuning potential takes place in the arrangement of FIG. 5 by means of the voltage source 20. The voltage supplying the tuning diodes may for example be taken from the wiper contact 13 of the tuning potentiometer 14, from a fixed voltage divider 21 or from the wiper contact of the adjustment potentiometer 9. Several adjustment potentiometers may be provided instead of only one adjustment potentiometer.

The arrangement of FIG. 6 is distinguished from the arrangement of FIG. 5 by the fact that the minimum tuning potential is made settable instead of the maximum tuning potential for the purpose of adjustment. Moreover, in the arrangement of FIG. 6, the network which comprises the voltage divider 21 and the adjustment potentiometer 9, is connected between the wiper contact 13 of the adjustment potentiometer 14 and the maximum tuning potential 11.

According to FIG. 7, the maximum and minimum tuning potential is produced by means of a circuit arrangement 15 which has the object of supplying such a temperature effect of the potential that the temperature effect of the tuning circuit is compensated by an appropriate temperature effect of the potentials.

The arrangement 16 of FIG. 8 also produces the minimum and maximum tuning potentials at the points 11 and 12 as well as the effective temperature on these potentials which is required for temperature compensation of the tuning circuit. In addition, the arrangement 16 contains a decoupling circuit which lies between the wiper contact 13 of the tuning potentiometer 14 and the adjustment potentiometers 9 and 10.

The tuning circuit dealt with in the embodiments is developed for positive tuning potentials. In a similar manner, the tuning circuits of the invention may also be designed for negative tuning potentials.

It will be understood that the above description of the present invention is susceptible to various modification changes and adaptations.

AY3-8203


Miscellaneous Digital Circuit - ECONOMEGA/16ch Digital Tuning System.
General Semiconductor, Inc.

Vsup(-) Nom.(V) Neg.Sup.Volt.=0
Vsup(+) Nom.(V) Pos.Sup.Volt.=12
Status=Discontinued
Package=N/A
Pins=N/A
Military=N
Technology=MOS.

 
FEATURES:

8/12/16 Programs
3/4 Bands
10 bit Coarse-Tune
4 bit Fine-Tune
Non-Volatile Memory without battery
Auto or Manual Tuning
Auto or Manual Band switching.

DESCRIPTION
The ECONOMEGA Digital Tuning system is a three chip voltage synthesizer. The first chip (AY-5-8203) is an n-channel control chip which interfaces the remote control system, memory and D/A converter. The second chip (ER1400) is a non-volatile EAROM memory which stores the tuning and band information for 16 programs. The third chip is a CMOS Buffer amplifier/switch. This amplifies the converter output from the control chip to a fixed reference voltage and also contains the switch circuitry for the fine time slot. For detailsor] the MEM4956 D/A converier circuit and the ER1400 EAROM, refer to the separate data sheet in this section.
NOTE: 10 bits of coarse time and 4bits of fine tune does not mean the resolution is 14 bits (described later). The overall resolution is: Band 3 - 11 bits Bands 1, 2, & 4 - 10 bits.

OPERATION
1. Coarse Tune
The coarse tune resolution is 10 bits with a predominant output ripple at 3.9kHz.

2. Fine Tune
The fine tune resolution is 4 bits with an output ripple at 15.6kHz. The fine tune steps twice per second related to system clock; it does not wrap around or overflow into coarse tune. During scanning it is reset to mid range.

3. Scanning
The actual tuning rates are fixed by the Tuning Clock and may be
adjusted over wide limits. Typical figures are shown below.
(a) Normal Mode
Operation of a band button initiates scanning on the
selected band, typical scan rates are as follows:
Band
 Scan Time
1
 0.8 sec.
2
 1.6 sec.
3
 8.0 sec.
4
 1.6 sec.
(b) Constant Time Scan Mode
Operation of a band button initiates scanning on the selected band. The scan rate is a constant 8 seconds for each band.
(c) Auto Band Switching Mode
At the end of each scan the band is automatically changed in the sequence 1, 2, 3, 4. In the 3 band mode, band 4 is omitted.

4. Auto Stop and Validate
In the Normal Mode a stop is executed immediately on a positive going input transition. If validate goes positive within 256 msec the system stops, if not the scan will restart (See Fig. 1 for a suggested validate circuit). At the end ot' a band the tuning voltage goes back to zero and after a delay of 256 msec scanning restarts. In the Constant Time Scan mode in Band 3, the stop is executed on a negative going transition.

5. Manual Operation
In the Normal Mode Stop and Validate can be linked to the Band Inputs to give full manual control of the tuning operation.

6. Muting
The Muting output is active from the time that a Scan is initiated until the Validate input goes positive after a Stop command. When a program change is made the Muting output is activated. for 256 msec.

7. Tuning Procedure:
(a) 1. Select required program number (1 to 16).
2. Press required band button, scanning commences
from the station currently tuned, scanning stops at the
next station.
3. Fine tune if required.
4. Store Data.
(b) Alternatively using the circuitry shown in Fig. 2, the
following procedure is available:
1. Press Band or Start.
2. Press Store.
3. Press required program.

8. Fine Tune Resolution
When the MEM4956 D/A is used to combine the Coarse and Fine Data the relationship between Coarse Tune and Fine Tune is as follOWS:
Band 1
Band 2. 4
Band 3
1 FT step = 7.5 CT steps
1 FT step = 2.5 CT steps
1 FT step = 0.5 CT steps.

9. Additional Fine Tune Information
The fine tune output is a rectangular waveform with a frequency of 15.6kHz (system clock +128). The mark/space ratio defines the fine tune level. 16 steps being possible. The following diagram relates the binary number within the fine tune store to the output waveform. Bit width is approximately 3.8,Js for a 15.6kHz output waveform.

10. Additional Coarse Tune fnformatlon
The Coarse tune output is a rectangular waveform with a predominant ripple frequency of 3.9kHz (system clock +512). The mark/space ratio indicates the coarse tune level. The addition of a coarse tune bit increases the mark period by approx. 1.0pS for a 2.0MHz clock. There are thus 256 bits within the 3.9kHz period. This accounts for8 of the 10 coarse tune bits. The information from the remaining 2 bits (LS .Bits) is used to add O. 1. 2. or 3 extra bit periods (1.0ps) over 4 periods of the basic waveform. The complete coarse tune waveform repeats every 1 ms.


11. MEM 4956 Buller
This buffer combines coarse and fine data under the control of the Fine Time slot output from the control chip. The fine time slot controls the CMOS switch and hence the times the coarse tune or fine tune information are routed to the output filter. Note the fine tune waveform is filtered before being routed to the switch.