ITT DIGIVISION 3888 I HI FI Ident - Nr. 5435 32 70 Chassis DIGI B 110° FST / IFB - 483 YEAR 1987.

ITT DIGIVISION 3888 I HI FI Ident - Nr. 5435 32 70 Chassis DIGI B 110° FST / IFB - 483
Year 1987 - 28 Inches (66Cm) Stereo & TeleText + multistandard.

The ITT DIGIT2000 chipset is the core of all Audio and Video processing. From the composite CVBS signal all processing is executed in the DIGIT2000 chipset board which improves signal quality and dynamic without needing any regulations or setup.

The TV set of the future will use digital techniques for most, if not all, of its functions. The process of converting to digital design is 'anything but easy and the process is likely to be long drawn out. It has already started, with some amazing new designs in workshops, but it's unlikely we will see true digital TV before the twenty-first century........

As digital TV reception technology offers many unique benefits to manufacturers and users, its concept is increasingly accepted. From the manufacturer's point of view, the use of digital circuits can replace hundreds of components, thus greatly simplifying the debugging of the TV set, and only need to equip the production line with a robot to complete the debugging work. From the user's point of view, digital TVs have unique performance characteristics, such as ghost compensation, image set images, etc., which are unheard of in standard TV sets. This post introduces the development of digital integrated circuits of the International Telephone and Telegraph Corporation (ITT Semiconductor Division), pointing out the main features and simplicity of digital integrated circuit technology................

THE SMART MONEY was betting that by the early 1990s most of the TV sets sold around the world will have digital circuits. Everywhere engineers were racing to be the first to put out a completely digital design. And the electronics giants of Japan, Europe and the US were watching them carefully. There have been some successes already. In Europe the ITT subsidiary Intermetall has produced a kit of five VLSI chips that digitise the vision path between the demodulator and the output amplifier. According to ITT, this represents the integration of almost 300 000 transistor functions. Motorola had a similar set of chips it calls the System 4 that mixes digital and analogue functions on the chips. There has also been considerable progress towards a digital frame store (DFS). A DFS is a device that stores the whole picture (frame) as a series of digits in one set of memory. In Europe, Philips has unveiled the first primitive model and Sony in Japan seemed to be heading down the same track. TV designers have been quick to jump on these developments. Virtually all of them  have had prototype sets up and running that use digital chip sets. Sony had already released one in Japan and plans to release it here within the next two years after 1983. National, likewise, had released its first digital TV in Japan, using the ITT chip set, but there are no plans yet to release it in this country. Hitachi also claims to be working on one, but according to its Melbourne office, the details were still "confidential". The primary US contender is the Zenith Corporation, which had a prototype up and running.

Advantages: So, what's all the fuss about? Why digitise TV sets at all? Well, there are some fairly predictable answers: digital sets are claimed to offer greater immunity to noise and ghosting, better resolution, and ease of interfacing to other digital sources like personal computers and videotext systems. They also offer the designer the ability to do very sophisticated manipulations on the image data, manipulations that would be virtually impossible in a reasonably priced analogue set. Looking down the track just a little way, say within the next ten years, designers are looking at sets with 1250 non -interlaced lines, and flicker -free pictures of unparalleled clarity. They would be hardware independent of the transmission format, requiring only reprogramming of their DFS to handle any of the standards now in use, (or any that might originate in the future). Another facility that will be standard on most of these sets will be second source windows. These are small insets that can be made to show the output of a second source, like a VCR or video camera. The user will be able to select the size of the window and position it anywhere on the screen, as well as independently controlling brightness, colour etc, just as for the main screen.

History:Digital techniques were introduced to TV sets in the early 1960s when remote control equipment began to appear in top -of-the - line models. Microprocessor based systems followed quickly. Text information systems like Teletext and Viewdata began to. appear in the mid to late 1970s. They all require some digital processing before being video delivered amplifiers. to the analogue circuitry of the Until quite recently though, digital TV has taken a back seat in most research labs to high definition, wide bandwidth systems. The conventional wisdom has been that more gains could be made more quickly by developing analogue technology. Modern top-of-the -line analogue systems have superb definition. They can also be made very small. In November 1983 Philips unveiled a black and white set with all its essential functions on a single IC. Two chip colour sets have also been demonstrated. But even as this trend towards large scale integration has been goipg on there has been a slow but steady increase in the amount of digital design being included in the average circuit. Clive Sinclair (the flamboyant British designer of the ZX80/81 and Spectrum computers) has shown a compos ite digital/analogue chip set intended for use with his up and coming flat screen TV. While most of the signal path is conventional the deflection circuits are all digital. Motorola has also gone a long way down this track with its System 4 design. It also uses a composite analogue-digital design. At least part of the problem with developing digital  digital processing designs is conceptually has been that far easier while than analogue, it takes a lot more components to do the same job. This in turn implies a far more complex circuit, with associated manufacturing and servicing expenses. The only way to keep cost down and integration number up to quality. The of components problem up is with is that that the large need  to integration to be large and  integrated pushes the state of the art to the limit. So there was a certain amount of surprise in the industry when, in 1982, Intermetall announced the creation of a completely digital video and audio section called, with alarming originality, the 'Digivision' chip set. It was a five chip set with three of them handling the video signal: a coder/decoder (codec), a processor and deflection pro cessor. The audio was carried on the other two. In order to make the system run it also required a microprocessor, an EEPROM and a clock, giving an absolute minimum part count of eight ICs plus a few capacitors. The managing director of ITT Semiconductor, Lubo Micic , (Micic, Ljubomir Dipl-ing) has been quoted as saying that this represents just the first step in an advance that will see the creation of an entirely digital design on a single chip.

 Digital video gear had its genesis in 1982, when ITT Semi conductors Worldwide, the West German subsidiary of International Telephone & Telegraph, demonstrated its "Digivision" system. The system consisted of a set of five IC (integrated- circuit) and VLSI (very large integrated- circuits) microchips in a conventional TV chassis. GE and Zenith were the first American firms to become licensees for the set. By the end of 1983, Matsushita, Sanyo, Sharp, Sony, and Toshiba had all shown digital -TV prototypes with ITT -chips. NEC showed a system it claims to have developed with Japanese broadcaster NHK. ITT subsidiaries Standard Electrik Lorenz (SEL) and Graetz began marketing digital TVs in Europe. In the U.S., Matsushita (Quasar's parent) and Panasonic were the first to announce digital TV plans. Toshiba, however, beat Matsushita to the marketplace with the CZ -2095 shown at the 1984 Summer CES and made commercially available in '85. Currently, ITT is virtually the only supplier of digital-video chips, and it plans to open a new manufacturing plant in Connecticut, to join its facility in Freiburg, West Germany. These chips each have 256K (over 256,000 bits) of computer RAM (random access memory). Other major electronics manufacturers are already developing their own digital-video technology. Mitsubishi has demonstrated a digital -TV prototype; and Japan's Matsushita, NEC, NMB Semiconductor and To- shiba, plus Korea's Goldstar, are developing one-megabit (approximately one million bits) DRAM (dyanmic RAM) chips. Toshiba's rudimentary digital VCR already uses such a chip. Digital TVs are still relatively primitive. Even the picture within picture gimmick requires a second video source (such as a VCR) along with the digital TV's tuner. Digital TVs can freeze the frame in the window. They also have features found on high-end standard TV sets, such as broadcast stereo /second audio channel capability, on- screen indicators, etc. Truly digital consumer VCRs are at least as far away as digital audio tape recorders. In 1984, Hitachi's professional /broadcast division developed a broadcast-use, 1/2 -inch VCR that recorded digitally on metal tape, but the company could not even speculate when such a VCR might be available to consumers. As chip technology continues to develop and fewer are needed per TV set, and as mass production lowers prices, digital video seems certain to find as much of a niche as did CD. Prototypes have already been demonstrated that let the user add and change on-screen colors; allow zoom -in for close -up scrutiny; add computer -generated scan lines for high -resolution pictures; and offer image manipulation, and performance monitoring. Since digital TVs are and will be compatible with existing broadcast, cable, and video signals, the transition will likely be as peaceful as the transition to color.

Digital Signal Processing DIGVISION ITT in Brief:

 FOR several years now the use of digital techniques in television has been growing. A considerable impetus came initially from the need for high -quality Tv standards conversion. The IBA's DICE (Digital Intercontinental Conversion Equipment) standards converter came into operational use in 1972. It's success demonstrated convincingly the advantages of processing video signals in digital form - digital signals are neither phase nor level dependent. The trend since then has been towards the all - digital studio: digital effects generators have been in use for some time, and digital telecines were announced earlier this year. An earlier example of the application of digital techniques to television was the BBC's sound-in-syncs system, in which the sound signal is converted to digital form so that it can be added to the video signal for network distribution. The sound-in-syncs system first came into use in 1969, and is was  widely employed in pay tv systems alongside with video scrambling methods in the 80's.  Digital techniques have already appeared on the domestic TV scene. The teletext signals are digital, and require digital processing. In modern remote control systems the commands from the remote control transmitter are in digital form, and require digital decoding and digital - to -analogue conversion in the receiver before the required control action can be put into effect. Allied to this, digital techniques are used for the more sophisticated channel tuning systems. The basic TV receiver itself continues to use analogue techniques however. Are we about to see major changes here? 
ITT Semiconductors in W. Germany have been working on the application of digital techniques to basic TV receiver signal processing since 1977 with the supervision of the Engineer Micic Ljubomir, and at the recent Berlin Radio Show presented a set of digital chips for processing the video, audio and deflection signals in a TV receiver. The set consists of a' couple of l.s.i. and six v.l.s.i. chips - and by very large scale integration (v.l.s.i.) we're talking about chips that contain some more 200,000 transistors. What are the advantages? 
For the setmaker, there's reduction in the component count and simpler, automated receiver alignment - alignment data is simply fed into a programmable memory in the receiver, which then adjusts itself. Subsequently, the use of feedback enables the set to maintain its performance as it ages. From the user's viewpoint, the advantages are improved performance and the fact that extra features such as picture -within -a -picture (two pictures on the screen at the same time) and still pictures become relatively simple to incorporate. The disadvantage of course is the need for a lot of extra circuitry. Since the received signals remain in analogue form, analogue -to -digital conversion is required before signal processing is undertaken. As the c.r.t. requires analogue drive signals, digital -to -analogue conversion is required prior to the RGB output stages - the situation is somewhat different in the timebase and audio departments, since the line drive is basically digital anyway and class D amplifier techniques can be used in the field and audio output stages. In between the A -D conversion and the various output stages, handling the signals in digital form calls for much more elaborate circuitry - hence those chips with 200,000 or so transistors. The extra circuitry is all incorporated within a handful of chips of course, but the big question is if and when the use of these chips will become an economic proposition, taking into account reduced receiver assembly/setting up costs, compared to the use of the present analogue technology - after all, colour receiver component counts are already very low. With the present digital technology, it's not feasible to convert the signals to digital form at i.f. So conversion takes place following video and sound demodulation. Fig. 1 shows in simple block diagram form the basic video and deflection signal processing arrangement used in the system devised by ITT Semiconductors. Before going into detail, two basic points have to be considered - the rate at which the incoming analogue signals are sampled for conversion to digital form, and the number of digits required for signal coding. Consider the example shown in Fig. 2. At both (a) and (b) the signals are sampled at times Ti, T2 etc. In (a) the signal is changing at a much faster rate than the sampling rate. So very little of the signal information would be present in the samples. In (b) the rate at which the signal is changing is much slower, and since the sampling rate is the same the samples will contain the signal information accurately. In practice, the sampling rate has to be at least twice the bandwidth of the signal being sampled. Once you've got your samples, the next question is how many digits are required for adequate resolution of the signal, i.e. how many steps are required on the vertical (signal level) scale in Fig. 2 The use of a four -digit code, i.e. 0000, 0001 etc., gives 16 possible signal levels. Doubling the number of digits to eight gives 256 signal levels and so on. ITT's experience shows that the luminance signal requires 8 bits (digits), the colour -difference signals require 6 bits, the audio signal requires 12 bits (14 for hi-fi quality) while 13 bits are required for a linear horizontal scan on a 26inch tube. These digital signals are handled as parallel data streams in the subsequent signal processing. Returning to Fig. 1, the A -D and D -A conversion required in the video channel is carried out by a single chip which ITT call the video codec (coder/decoder). A clock pulse generator i.c. is required to produce the various pulse trains necessary for the digital signal processing, and a control i.c. is used to act as a computer for the whole digital system and also to provide interfacing to enable the external controls (brightness, volume, colour etc.) to produce the desired effects. In addition, the control i.c. incorporates the digital channel selection system. The video codec i.c. uses parallel A-D/D-A conversion, i.e. a string of voltage comparators connected in parallel. This system places a high premium on the number of bits used to code the signal in digital form, so ITT have devised a technique of biasing the converter to achieve 8 -bit resolution using only 7 bits (the viewer's eye does some averaging on alternate lines, as with Simple PAL, but this time averaging luminance levels). The A -D comparators provide grey -encoded outputs, so the first stage in the video processor i.c. is a grey -to -binary transcoder. As Fig. 3 shows, the processes carried out in the video processor i.c. then follow the normal practice, though everything's done in digital form. The key to this processing is the use of digital filters. These are clocked at rates up to 18MHz, and provide delays, addition and multiplication. The glass chroma delay line required for PAL decoding in a conventional analogue decoder consists of blocks of RAM (random-access memory) occupying only three square millimeters of chip area each. As an example of the ingenuity of the ITT design, the digital delay line used for chroma signal averaging/separation in the PAL system is used in the NTSC version of the chip as a luminance/chrominance signal separating comb filter. Fig. 4 shows the basic processes carried out in the deflection processor i.c. This employs the sorts of techniques we're becoming used to in the latest generation of sync processor i.c.s. Digital video goes in, and the main outputs consist of a horizontal drive pulse plus drives to the field output and EW modulator circuits. The latter are produced by a pulse -width modulator arrangement, i.e. the sort of thing employed with class D output stages. The necessary gating and blanking pulses are also provided. A further chip provides audio signal processing. One might wonder why the relatively simple audio department calls for this sort of treatment. The W. German networks are already equipping themselves for dual -channel sound however, and the audio processor i.c. contains the circuitry required to sort out the two -carrier sound signals. These chips represent a major step in digitalizing the domestic TV receiver. It seems likely that some enterprising setmaker will in due course announce a "digital TV set". The interesting point then will be whether the chip yields, and the chip prices as production increases, will eventually make it worthwhile for all setmakers to follow this path (in 1984).





(To see the Internal Chassis Just click on Older Post Button on bottom page, that's simple !)


DIGITAL Colour television receiver or set , are known in which the majority of signal processing that takes place therein is carried out digitally. That is, a video or television signal is received in a conventional fashion using a known analog tuning circuit and then, following the tuning operation, the received analog television signal is converted into a digital signal and digitally processed before subsequently being converted back to an analog signal for display on a colour cathode ray tube.
In a conventional television receiver, all signals are analog-processed. Analog signal processing, however, has the problems at the video stage and thereafter. These problems stem from the general drawbacks of analog signal processing with regard to time-base operation, specifically, incomplete Y/C separation (which causes cross color and dot interference), various types of problems resulting in low picture quality, and low precision of synchronization. Furthermore, from the viewpoints of cost and ease of manufacturing the analog circuit, a hybrid configuration must be employed even if the main circuit comprises an IC. In addition to these disadvantages, many adjustments must be performed.

In order to solve the above problems, it is proposed to process all signals in a digital form from the video stage to the chrominance signal demodulation stage. In such a digital television receiver, various improvements in picture quality should result due to the advantages of digital signal processing.
Therefore digital television signal processing system introduced in 1984 by the Worldwide Semiconductor Group (Freiburg, West Germany) of International Telephone and Telegraph Corporation is described in an ITT Corporation publication titled "VLSI Digital TV System--DIGIT 2000." In that system color video signals, after being processed in digital (binary) form, are converted to analog form by means of digital-to-analog converters before being coupled to an image displaying kinescope. The analog color video signals are coupled to the kinescope via analog buffer amplifiers and video output kinescope driver amplifiers which provide video output signals at a high level suitable for driving intensity control electrodes of the kinescope.

The ITT DIGIVISION 3876 HIFI OSCAR  Is a multistandard set and relates to a digital multistandard decoder for video signals and to a method for decoding video signals.
Colour video signals, so-called composite video, blanking and sync signals (CVBS) are essentially composed of a brightness signal or luminance component (Y), two colour difference signals or chrominance components (U, V or I, Q), vertical and horizontal sync signals (VS, HS) and a blanking signal (BL).
The different coding processes, e.g. NTSC, PAL and SECAM, introduced into the known colour television standards, differ in the nature of the chrominance transmission and in particular the different systems make use of different colour subcarrier frequencies and different line frequencies.
The following explanations relate to the PAL and NTSC systems, but correspondingly apply to video signals of other standards and non-standardized signals.
The colour subcarrier frequency (fsc) of a PAL system and a NTSC system is fsc(NTSC) = 3.58 MHz or fsc(PAL) = 4.43 MHz.
In addition, in PAL and NTSC systems the relationships of the colour subcarrier frequency (fsc) to the line frequency (fh) are given by fsc(NTSC) = 227.50 * fh or 4•fsc(NTSC) = 910 • fh fsc(PAL) = 283.75 * fh or 4•fsc(PAL) = 1135 • fh so that the phase of the colour subcarrier in the case of NTSC is changed by 180°/line and in PAL by 270°/line.
In the case of digital video signal processing and decoding the prior art fundamentally distinguishes between two system architectures. These are the burst-locked architecture and the line-locked architecture, i.e. systems which operate with sampling frequencies for the video signal, which are produced in phase-locked manner to the colour subcarrier frequency transmitted with the burst pulse or in phase-locked manner with the line frequency, respectively.

The principal advantage of the present invention is a color television receiver is provided having a fully digital color demodulator wherein the luminance signal and the chrominance signals are separated and digitally processed prior to being converted to analog signals in that the all-digital signal processing largely eliminates the need for nonintegratable circuit elements, i.e., particularly coils and capacitors, and that the subcircuits can be preferably implemented using integrated insulated-gate field-effect transistor circuits, i.e., so-called MOS technology. This technology is better suited for implementing digital circuits than the so-called bipolar technology.

The ITT DIGIVISION 3876 HIFI OSCAR  is a multisound tv digital sound processing.


- High contrast bright, because of the digital processing, lot of more dynamic is gained.

- High precision detailed picture, because of the digital processing any particular of the picture even the little point is processed and improved.

- Super color dynamic, because of the digital processing, colors are gaining power and precision details but without producing any kind of no reality like many modern CRAPPY LCD & Co.

The ITT DIGIT2000 chipset is the core of all Audio and Video processing. From the composite CVBS signal all processing is executed in the DIGIT2000 chipset board which improves signal quality and dynamic without needing any regulations or setup.

This technology is introducing even an another important group of revolutionary features:
NO MORE REGULATIONS needed via trimmers and / or potentiometers.

All setups regarding picture / CRT / SOUND are executed in the digital domain via a special kind of setup feasible via special tools or via a SERVICE MODE SETUP and parametrized via remote
controller and front display steps followed engineering menu.
It's Useless to say that the pictures produced by this set are excellent for precision and brightness and quality.

Even the sound has superb bass AUDIO and response to all sounds in perfect ways.

(To see the Internal Chassis Just click on Older Post Button on bottom page, that's simple !)

----------------------------------------------------------------

Here is the Announcement article from DER SPIEGEL a GERMAN journal which was discussing the introducing marketing of the DIGIVISION ITT TECHNOLOGY:

(This article is in original GERMAN Language)

FERNSEHEN

Vorteil im Verborgenen

Die ersten computergesteuerten Fernseher kommen in die Geschäfte - für den Verbraucher bringen sie vorerst kaum Vorteile. *

Das Gerät sieht aus wie jeder andere Fernseh-Apparat, auch Bild und Ton sind keineswegs besser. Aber nach Ansicht der Ingenieure ist es ein "technologischer Meilenstein".
Gemeint ist das neueste Gerät der Standard Elektrik Lorenz (SEL) - ein computergesteuerter Fernseher namens Digivision. "Mit Freude und Stolz" hatte SEL-Vorstandschef Helmut Lohr seinen
Aktionären den Apparat auf der letzten Hauptversammlung präsentiert. Ende dieses Monats soll es nun den digitalen Fernseher zu kaufen geben.
Vorerst allerdings dürfte der rund 2700 Mark teure Apparat allein fortschrittshungrige Techniker begeistern. Es ist der erste Farbfernseher der Welt, der Bild- und Tonsignale digital, wie ein Computer, verarbeitet.
Die Idee stammt von dem jugoslawischen Ljubomir Dipl.-Ing. Micic. Der hatte bereits vor zehn Jahren bei der Firma Intermetall in Freiburg, einer Tochter des amerikanischen ITT-Konzerns, zu dem auch SEL gehört, die Grundlage für Digivision entwickelt.
Mikroprozessoren, so schlug Micic vor, sollten die von den Sendern kommenden Fernsehsignale in Zahlencodes verwandeln. Um eine optimale Bildqualität zu erreichen, müßte eine andere Rechnereinheit die in digitale Codes verwandelten Signale überprüfen und, falls nötig, korrigieren. Die so aufbereiteten Signale würden dann wieder in ihre ursprüngliche Wellenform gebracht und das Fernsehbild produzieren.
Doch vor zehn Jahren wußten die Techniker die nahezu unbegrenzten Möglichkeiten der neuen Mikroprozessoren noch nicht recht zu nutzen. Die fingernagelgroßen Chips, die alle zentralen Funktionen eines großen Computers übernahmen, waren gerade erst zwei Jahre auf dem Markt.
Inzwischen hat Intermetall mehr als 40 Millionen Mark investiert, um Chips zu entwickeln, die ohne Zeitverzögerung die wellenförmigen Fernsehsignale in digitale Codes umwandeln. Und weitere Millionen sind erforderlich, damit auch der Verbraucher die Wunder der neuen Technik nutzen kann. So soll der Digital-Fernseher
eines Tages Bildstörung

en wie Flimmern oder Streifen auf der Mattscheibe automatisch beseitigen. Der Zuschauer soll auch Standbilder oder vergrößerte Bildausschnitte wählen können.
Doch dazu müssen die digitalen Fernsehsignale durch einen elektronischen Speicher geschickt werden, der etwa die gewünschten Standbilder später wieder hergibt. Ein solcher Speicher aber ist bislang in keinem der jetzt käuflichen Geräte eingebaut.
Das Problem ist die unvorstellbare Menge an Daten, die ein solcher Speicher aufnehmen müßte. Um das Standbild zu liefern, muß der Speicher alle für das Fernsehbild notwendigen Informationen festhalten können. Bei einem Farbbild sind das rund vier Millionen digitaler Informationen (bits) pro Sekunde.
Diese Datenflut läßt sich mit den heute verfügbaren Speichern auf dem engen Raum eines Fernsehgeräts kaum verarbeiten. Mehr als 250 der heute üblichen Chips wären erforderlich. Der Preis für das Gerät stiege dadurch um mindestens 1500 Mark.
Frühestens in zwei Jahren, so rechnen die Experten, wird es möglich sein, die Zahl der für den Datenspeicher notwendigen Chips drastisch zu reduzieren. Dann könnten störungsfrei arbeitende Fernseher mit Standbild und Ausschnittvergrößeru

ng als Luxusmodelle mit etwa 600 Mark Aufpreis angeboten werden.
Bislang wirken sich die Vorzüge des neuen Fernsehers vor allem für die Hersteller aus: Die Chips machen den Fernseher computergerecht. Zum Beispiel die Einstellung von Helligkeit und Bildschärfe sowie die Endkontrolle im Werk können von einem Rechner übernommen werden.
Die Folge: Die Geräte kommen noch schneller vom Band. Seit Mitte der siebziger Jahre fiel die Produktionszeit für einen Fernseher bereits von acht auf zwei Stunden. Mit Hilfe der Digitaltechnik läßt sich nun noch einmal mindestens eine halbe Stunde einsparen.
Solche Rationalisierungsvorteile weckten das Interesse der Konkurrenz. Bereits 18 Gerätehersteller aus aller Welt, darunter Sony, Grundig und Blaupunkt, verhandeln mit Intermetall. Die für 1983 vorgesehene Produktion von 200 000 der neuen Chips ist bereits verkauft. Im kommenden Jahr soll die zehnfache Menge produziert werden.
Der ITT-Konzern hat schon jetzt 60 Millionen Mark in die Fabrikation der Chips gesteckt. Bis 1987 will der US-Multi noch einmal 350 Millionen Mark investieren. "Wir sind", so ein Intermetall-Manager, "vielleicht ein halbes Jahr weiter als die Konkurrenz, und diesen Vorsprung müssen wir nutzen."
In der Tat ziehen die Konkurrenten nach. Halbleiter-Produzenten wie Siemens, Texas Instruments oder Motorola sehen ebenfalls eine Chance, ihr Bauteile-Geschäft auszuweiten. Immerhin werden jährlich weltweit rund 50 Millionen Fernseher gebaut - für die Chips-Hersteller tut sich da ein ganz neuer Markt auf.
Für den Verbraucher dagegen, der sich ein neues Fernsehgerät anschafft, liegen die Vorteile der Digital-Technik eher noch im Verborgenen: Im Gerät ist weniger drin - sechs Mikrochips ersetzen rund 300 von etwa tausend herkömmlichen Bauteilen.
Im Gebrauch muß deshalb ein solcher Apparat zuverlässiger sein: Was nicht drin ist, so ein alter Techniker-Schnack, kann auch nicht kaputtgehen. _(Sechs Chips einer ITT-Leiterplatte ) _(ersetzen rund 300 konventionelle ) _(Bauteile. )

Sechs Chips einer ITT-Leiterplatte ersetzen rund 300 konventionelle Bauteile.
DER SPIEGEL 41/1983
Alle Rechte vorbehalten
Vervielfältigung nur mit Genehmigung der SPIEGEL-Verlag Rudolf Augstein GmbH & Co. KG.

------------------------------------------------------------------------------------------------------------------------------------------------------------- 

In 1980 Ljubomir  Micic has taken the position  of  managing  director  of the itt  semiconductors and  he was responsible WorldWide company's activities, for  which  encompassed 3,500 employees and   five plants in the US, France and West Germany.

  Ljubomir  Micic joined  ITT in 1959, after graduating from Belgrade University.
  His   first positiont was quality control engineer  at intermelall, and in 1967 he became   manager of its application laboratory,
 
  Between 1968 and 1974 he was production manager responsible for new product  development and introduction.
  From 1974 to 1978 he managed all ITT   Semiconductor's  sales marketing in  Europe as director,
 
  In 1978, Ljubomir  Micic was appointed director of marketing and business development for ITT Semiconductors  World Wide, assuming the added res ponsibility of director for Intermetall  In 1979.

--------------------------------------------------------------------------------------------------------------------------------------------------------------

An Increasingly Versatile Device The domestic television set used to be simply the thing that reproduced the programmes transmitted by one or other of the three programme networks  unless you happened to be connected to one of the wire systems that have experimented with local TV and pay TV at various times. But have you noticed what an increasingly versatile thing the TV set is becoming?
- The first major extension to the domestic TV set's possibilities came with the VCR, enabling you to record off air or replay prerecorded tapes. Domestic VTR systems have at a price  been with us for roughly a decade now, but till the advent of the easy to handle VCR most low-cost VTR systems were intended for use with monitors, with the signal interconnections at video and audio frequencies.
- Then came TV games, first found in the pubs and amusement arcades, later appearing in compact, relatively inexpensive packages for home use. The significant point here was the entry of digital techniques on the domestic TV scene. On the broadcast side, digital techniques had been making a substantial contribution to operations for some years, starting with the BBC's sound-in-syncs system (1969) in which the TV sound signal is compressed, converted to digital form and inserted in the line sync pulse period, and culminating with the IBA's famed DICE, which provides electronic standards (lines, fields, colour) conversion by converting the signals to digital form, processing them, then converting them back into analogue form.
Rather far from TV games you might think, but it's all part of the same process - the increasing impact of digital techniques on the world of television. In fact the technology of TV games has evolved considerably since their first appearance.
The approach then was to employ a fair number of standard digital i.c.s to build up the circuitry required. But why not go about it in the same way as the calculator manufacturers?
It didn't take long for the semiconductor people to see this new possibility for using their l.s.i. technology. This made it a relatively simple matter to provide a range of games with just a single i.c.  the basis of the present generation of TV games.
Add a second i.c. and the whole thing comes up in glorious colour. But it doesn't end there. The talk was now is of adopting microprocessor technology and making the system programmable, so that an almost unlimited range of games of varying degrees of complexity can be played. The favoured system seems to been to use prerecorded cassettes to provide the various programmes. And once you do that, you can extend the system to all sorts of other uses - teaching systems and so on. In fact you've made the TV set into part of a home computer installation - as we outlined in Teletopics last month. It's not impossible then to imagine some "viewers" using their TV sets for games, instruction and VCR use, while keeping up to date with teletext news and getting extra information via the PO's Viewdata system - and never watching a transmitted programme at all! We've come a long way then from the days of the TV set as a goggle

(goggle ????? or gooooooooooogle).................. box.
Teletext decoders and TV games were already being built into a few sets. What other digital innovations can we expect in TV sets? (may be DVB)
One now well established use of digital techniques is to provide all electronic channel selection.
The varicap tuner simply asks to be controlled in this way, and the system lends itself readily to remote control operation. Once you're controlling the tuner and generating various signals digitally there are other things you might as well do. Like flashing the selected channel number on the screen, or the time (coming shortly in Television!). Sets which do this sort of thing have been available on the Continent for some while now.
- The latest development along these lines is the picture within a picture a reduced size picture from another channel being inserted in the corner of the main display (PIP), so that you can watch two progrpnmes at once or see when to change over to a programme due to start on another channel. This involves some interesting digital processes - you've got to lose lines, and compact the video information by reading it into a memory at one speed and reading it out at another, in effect operating at two standards simultaneously while keeping both in sync (remember how difficult it has sometimes been to keep a set in sync on one standard!).
- There's only one thing that prevents a space-age TV installation in every home: cost.
But the cost of electronic hardware has a habit of falling dramatically once production has achieved a certain level. TV games are already commonplace, and teletext decoders have  become a lot cheaper once specialised i.c. modules for the purpose go into large scale production. From this point in time, it already seems that one can regard the days when the TV set simply displayed one of the programmes available as the age of stream TV.

....................................But we all know how it ended !

One more comment about digital in 2000..............

Over the years we have learnt that one of the most important things in video/ TV technology is selecting the best system to use. We have also seen how difficult this can be. Prior to the start of the colour TV era in Europe there was an great to-do about the best system to adopt. The US NTSC system seemed an obvious choice to start with. It had been proved in use, and refine- ments had been devised. But alternative, better solutions were proposed - PAL and Secam. PAL proved to be a great success, in fact a good choice. 

The French Secam system seems to have worked just as well. Apart from the video tape battles of the Seventies, the next really big debate concerned digital TV. When it came to digital terrestrial TV (DTT), Europe and the USA again adopted different standards. 

One major difference is the modulation system used for transmission. Coded orthogonal frequency   division multiplexing (COFDM) was selected for the European DVB system, while in the USA a system called 8VSB was adopted. COFDM uses quadrature amplitude modulation of a number of orthogonal carriers that are spread across the channel bandwidth. Because of their number, each carrier has a relatively low bit rate. 

The main advantage of the system is its excellent behaviour under multipath reception conditions. 8VSB represents a rather older,  pre phase modulation technoogy: eight  state amplitude modulation of a single carrier, with a vestigial sideband. The decision on the US system was assigned to the Advanced Television Systems Committee (ATSC), reporting to the FCC. The system it proposed was approved by the FCC on December 26th, 1996. The curious date might suggest that there had been a certain amount of politicking. In fact there had been an almighty row between the TV and computer industries about the video standard to adopt, the two fearing that one or other would gain an advantage as the technologies converged. It was 'resolved' by adopting a sort of   "open standard"  we are talking about resolution and scanning standards here - the idea apparently being that the technology would somehow sort itself out.

 There seems to have been rather less concern about the modulation standard. 8VSB was adopted because it was assumed to be able to provide a larger service area than the alternatives, including COFDM, for a given transmitter power. Well, the USA is a very large place! But the US TV industry, or at least some parts of it, is now having second thoughts. Once the FCC had made its decision, there was pressure to get on with digital TV. In early 1998 there were announce- ments about the start of transmissions and broadcasters assured the FCC that DTT would be available in the ten areas of greatest population concentration by May 1999. Rapid advances were expected, with an anticipated analogue TV switch -off in 2006. So far however things have not gone like that. At the end of 1999 some seventy DTI' transmitters were in operation, but Consumer Electronics Manufacturers Association estimates suggest that only some 50,000 sets and 5,000 STBs had been sold.

 There have been many reports of technical problems, in particular with reception in urban and hilly areas and the use of indoor aerials, also with video/audio sync and other matters. Poor reception with indoor aerials in urban conditions is of particular concern: that's how much of the population receives its TV. The UK was the first European country to start DTI', in late 1998 - at much the same time as in the USA. The contrast is striking. ONdigital had signed up well over 500,000 subscribers by the end of 1999, a much higher proportion of viewers than in the USA. Free STBs have played a part of course, but it's notable that DTT 's reception in the UK has been relatively hassle -free. In making this comparison it should also be remembered that the main aim of DTT technology differs in Europe and the USA. 

The main concern in Europe has been to provide additional channels. In the USA it has been to move to HDTV, in particular to provide a successor the NTSC system. There have been plenty of channels in the USA for many a year. For example the DirecTV satellite service started in mid 1994 and offers some 200 channels. Internationally, various countries have been comparing the US and European digital systems. They have overwhelmingly come down in favour of the DVB system. There have been some very damaging assessments of the ATSC standard. The present concern in the US TV industry results from this poor domestic take up and lack of international success. Did the FCC make a boob, in particular in the choice of 8VSB? Following compara- tive tests carried out by Sinclair Broadcasting Group Inc., the company has petitioned the FCC to adopt COFDM as an option in the ATSC standard. Not only did its tests confirm poor reception with indoor aerials: they also established that the greater coverage predicted for 8VSB failed to materialise in practice. Could the USA have two DTT transmission standards? It seems unlikely. It would involve dual standard receivers and non  standardisation of transmitters. In the all important business of system selection, it looks as if the FCC got it wrong.

              ....................................   It is obviously wasteful to duplicate terrestrial TV transmissions in analogue and digital form. Sooner or later transmissions will all be digital, since this is a more efficient use of spectrum space. The question is when? It would suit some to switch off the analogue transmitters as soon as possible. 2006 has been suggested as a time to start, with ana- logue transmissions finally ending in 2010. All very neat and tidy. Whether it will work out in that way is another matter. Strong doubts are already beginning to be aired. 

 The government has, quite properly, laid down conditions to be met before the switch off occurs. Basically that the digital signal coverage should equal that achieved for analogue TV, currently 99.4 per cent of the population, and that digital receiving equipment should be available at an affordable price. The real problem is that there is a difference between a coverage of 99.4 per cent and 99.4 per cent of the population actually having digital receiving equipment. Why should those who are interested in only free - to -air channels go out and buy/rent a digital receiver? It is already becoming evident that this represents a fair chunk of the population. 

The ITC has warned the government that the 2006-2010 timetable is in jeopardy. Peter Rogers, the ITC's chief executive, has said "we need to persuade people only interested in watching free -to -air television to switch to digital. "

Unless we do, there will be no switch - over." Well not quite, because the analogue receivers will eventually wear out and have to be replaced. But that could take a long, long time. Meanwhile many people will expect to be able to continue to watch their usual TV fare using their existing analogue receivers. 

Research carried out by Culture Secretary Chris Smith's department has established that between forty and fifty per cent of the population expects the BBC licence to cover their TV viewing, which means what they get at present in analogue form. A substantial percentage of the population simply isn't interested in going digital. In fact take up of integrated receiver -decoders, as opposed to the free digital set -top boxes, has so far been very slow. 

Of five million TV sets sold in the UK year 1999 , only 10,000 were digital. There are important factors apart from overall coverage and how many people have sets. There is the extension of coverage, which becomes more difficult to achieve eco- nomically as the number of those not covered decreases. There is the problem of reception quality. And there is the question of domestic arrangements and convenience. Extending coverage to the last ten fifteen per cent of the population by means of conventional terrestrial transmitters will be expensive. Mr Smith's department seems to have conceded that other methods of signal delivery may have to be adopted - by satellite, by microwave links or by cable. The latter has of course never been economic where few households are involved. 

The frequency planners have been trying to find ways of increasing coverage even to well populated areas. There are so many areas where problems of one sort or another make the provision of DTT difficult. Satellite TV is the obvious solution. 

The time may well come when it is wondered why anyone bothered with DTT. Signal quality is becoming an increasingly important factor as the digital roll out continues. In areas where the signal is marginal, viewers could experience the extreme irritation of picture break up or complete loss like even todays. This is quite apart from the actual quality of the channel, which depends on the number of bits per second used. There is a maximum number of bits per multiplex, the total being shared by several channels. The fewer the bits, the poorer the picture in terms of definition and rendering. 

There have already been complaints about poor quality. The question of domestic arrangements is one that has not so far received adequate public attention. Most households 2000 nowadays don't have just one TV set that the family watches. They have a main one, probably, almost certainly one or more VCRs, and several other sets around the house to serve various purposes. What 'the percentage of households that have digital TV' should really mean is the percentage willing to replace all this equipment. It will be expensive, and people would not be happy if they were told to throw away their other equipment when they get a single nice new all  singing all dancing widescreen digital TV set. It fact there would be uproar. The move from analogue to digital is not like that from 405 to 625 lines, which went fairly smoothly.

In those days few people had video equipment or a multitude of sets. The transition to digital is not going to be smooth, and the suggestion of a switch off during 2006-2010 already looks totally unrealistic. Unless the government subsidises or gives away digital TV sets - and why should it? - people will expect their existing equipment to continue to be usable.  

So it's likely that analogue TV will be with us for many years yet. But that would be the end of analogue too. 

.............................Indeed...............................

----------------------------------------------------------------------------



ITT Corporation (NYSE: ITT) is a global diversified manufacturing company with 2008 revenues of $11.7 billion. ITT participates in global markets including water and fluids management, defense and security, and motion and flow control. Forbes.com named ITT Corporation to its list of "America's Best Managed Companies" for 2008, and awarded the company the top spot in the conglomerates category.

,ITT's water business is the world's largest supplier of pumps and systems to transport, treat and control water, and other fluids. The company's defense electronics and services business is one of the ten largest US defense contractors providing defense and security systems, advanced technologies and operational services for military and civilian customers. ITT's motion and flow control business manufactures specialty components for aerospace, transportation and industrial markets.

In 2008, ITT was named to the Dow Jones Sustainability World Index (DJSI World) for the tenth time in recognition of the company's economic, environmental and social performance. ITT is one of the few companies to be included on the list every year since its inception in 1999.

The company was founded in 1920 as International Telephone & Telegraph. During the 1960s and 1970s, under the leadership of its CEO Harold Geneen the company rose to prominence as the archetypal conglomerate, deriving its growth from hundreds of acquisitions in diversified industries. ITT divested its telecommunications assets in 1986, and in 1995 spun off its non-manufacturing divisions, later to be purchased by Starwood Hotels & Resorts Worldwide.

In 1996, the company became ITT Industries, Inc., but changed its name back to ITT Corporation in 2006.


History

ITT was formed in 1920, created from the Puerto Rico Telephone Company co-founded by Sosthenes Behn.[1] Its first major expansion was in 1923 when it consolidated the Spanish Telecoms market into what is now Telefónica.[2] From 1922 to 1925 it purchased a number of European telephone companies. In 1925 it purchased the Bell Telephone Manufacturing Company of Brussels, Belgium, which was formerly affiliated with AT&T, and manufactured rotary system switching equipment. In the 1930s, ITT grew through purchasing German electronic companies Standard Elektrizitaetsgesellschaft (SEG) and Mix & Genest, both of which were internationally active companies. Its only serious rival was the Theodore Gary & Company conglomerate, which operated a subsidiary, Associated Telephone and Telegraph, with manufacturing plants in Europe.

In the United States, ITT acquired the various companies of the Mackay Companies in 1928 through a specially organized subsidiary corporation, Postal Telegraph & Cable. These companies included the Commercial Cable Company, the Commercial Pacific Cable Company, Postal Telegraph, and the Federal Telegraph Company.



International telecommunications

International telecommunications manufacturing subsidiaries included STC in Australia and Britain, SEL in Germany, BTM in Belgium, and CGCT and LMT in France. Alec Reeves invented Pulse-code modulation (PCM), upon which future digital voice communication was based. These companies manufactured equipment according to ITT designs including the (1960s) Pentaconta crossbar switch and (1970s) Metaconta D, L and 10c Stored Program Control exchanges, mostly for sale to their respective national telephone administrations. This equipment was also produced under license in Poznań (Poland), and in Yugoslavia, and elsewhere. ITT was the largest owner of the LM Ericsson company in Sweden but sold out in 1960.



1989 breakup

In 1989 ITT sold its international telecommunications product businesses to Alcatel, now Alcatel-Lucent. ITT Kellogg was also part of the 1989 sale to Alcatel. The company was then sold to private investors in the U.S. and went by the name Cortelco Kellogg. Today the company is known as Cortelco (Corinth Telecommunications Corporation, named for Corinth, MS headquarters). ITT Educational Services, Inc. (ESI) was spun off through an IPO in 1994, with ITT as an 83% shareholder. ITT merged its long distance division with Metromedia Long Distance, creating Metromedia-ITT. Metromedia-ITT would eventually be acquired by Long Distance Discount Services, Inc. (LDDS) in 1993. LDDS would later change its name to Worldcom in 1995.

In 1995, ITT Corporation split into 3 separate public companies:

* ITT Corp. — In 1997, ITT Corp. completed a merger with Starwood Hotels & Resorts Worldwide, selling off its non-hotel and resorts business. By 1999, ITT completely divested from ITT/ESI; however, the schools still operate as ITT Technical Institute using the ITT name under license.[1] Also in 1999, ITT Corp. dropped the ITT name in favor of Starwood.[7]
* ITT Hartford (insurance) — Today ITT Hartford is still a major insurance company although it has dropped the ITT from its name altogether. The company is now known as The Hartford Financial Services Group, Inc.
* ITT Industries — ITT operated under this name until 2006 and is a major manufacturing and defense contractor business.
o On July 1, 2006, ITT Industries changed its name to ITT Corporation as a result of its shareholders vote on May 9, 2006.



Purchase of International Motion Control (IMC)

An agreement was reached on June 26, 2007 for ITT to acquire privately held International Motion Control (IMC) for $395 million. The deal was closed and finalized in September 2007. An announcement was made September 14, 2010, to close the Cleveland site.
Purchase of EDO

An agreement was reached September 18, 2007 for ITT to buy EDO Corporation for $1.7 billion.[12] After EDO shareholders' approval, the deal was closed and finalized on December 20, 2007.


Purchase of Laing

On April 16, 2009, ITT announced it has signed a definitive agreement to acquire Laing GmbH of Germany, a privately held leading producer of energy-efficient circulator pumps primarily used in residential and commercial plumbing and heating, ventilating and air conditioning (HVAC) systems.


2011 breakup

On January 12, 2011, ITT announced a transformation to separate the company into 3, stand-alone, publicly-traded, and independent companies.

 ITT'S KEY WEST GERMAN UNIT:

 April 29, 1985;

 When Standard Elektrik Lorenz A.G., the West German electrical company, abandoned devastated Berlin for this trim south German city after World War II, the only space available, company officials recall, was the underground assembly plants of a defunct aircraft manufacturer.

Ever since, Standard Elektrik, a $1.5 billion operation that is the largest European unit of the ITT Corporation, has been struggling for a place in the sun.

ITT took over most of the operations that today form Standard Elektrik in 1925, when it acquired all the manufacturing and research units that Western Electric owned outside North America. It now owns an 85.9 percent stake.

In recent years, Standard Elektrik has tried to define itself in a big market dominated by such giants as Germany's Siemens A.G. and the Netherlands' NV Philips, and within ITT's far-flung international business.

ITT Asset Divestment:
While not exactly suffering from an identity crisis, the German company seemed to be doing some reassessing when ITT announced in January that it planned to divest itself of $1.7 billion in assets this year and next, including shares of European subsidiaries.

It was after that announcement that Helmut Lohr, Standard Elektrik's fiercely independent chief executive, mused in a magazine interview that ''someday, the time will come'' when chunks of ITT companies would be spun off to shareholders ''through further emissions in Germany.''

Such remarks irk ITT officials in New York. ITT, which earns about half its operating income in Europe, believes the future of Standard Elektrik is crucial.

The 55-year-old Mr. Lohr said more recently in an interview that the issue was ''not yet ripe,'' but some people see Mr. Lohr's remarks as an indication that Standard chafes under the ITT yoke, and that its German management wants to wean it from the United States parent.

Dwindling Operating Income:
ITT's operating income from its mainstay European business has dwindled for several years, declining to $387 million last year on sales of $5.28 billion, from $633 million in 1982 on sales of $7.02 billion.

Daniel P. Weadock, executive vice president of ITT and president of ITT Europe Inc. in Brussels, said this was ''partly the result of the strong United States dollar,'' which depresses the value of earnings in local currencies; of new product start-up costs, and of higher outlays for research, development and restructuring.

Despite the decline, ITT has been working to improve the European subsidiaries and has made some major structural changes. There are plans to sell minority stakes in a number of companies to raise cash, appraise their value and open them wider for Government contracts by putting ownership partly in the hands of local citizens.

Last year, ITT announced it would spend $4.8 billion on research and capital investment in Europe in the next five years. More than $2 billion of that is set aside for West Germany, mainly to increase technological development in microelectronics, communications and motor vehicle components.

Standard Elektrik, with products such as its Digivision digital television system, is responsible for ITT's worldwide entertainment electronics business. Digital television uses chips to replace conventional components to simplify the set, make it easier and cheaper to build, and improve the quality of reception.

Four research centers - for microcomputers, telecommunications, television and automotive systems - are a major part of ITT's research effort, and spearheaded the $700 million effort that spawned the company's lucrative System 12 digital telephone exchange. System 12 has greater programming capabilities than other digital telephone systems.

Company Employs 27,000

Standard Elektrik had total sales equivalent to more than $1.5 billion last year. Its net income in 1984 amounted to $30 million, roughly the same amount as in 1983. The company employs 27,000 people, most of them in West Germany.

By all accounts, the breakthrough for Standard Elektrik came in 1982, when it beat giant Siemens to the market with a digital telephone exchange, forcing German postal authorities to crack Siemens's monopoly and award Standard Elektrik contracts for about 30 percent to 40 percent of the country's new digital switching technology.

There have been successes with the German military, too, including a $33 million stake in a consortium, headed by Standard Elektrik, to build a new digital communications network for the German armed forces.

Expectations about the telecommunications business, according to Gerhard Zeidler, Standard Elektrik's director of technology, center on linking ''text, data and pictures'' in complex new office systems in which the company sees a central role for its digital telephone and terminal technology.

But the odds are going up in the market for telecommunications and office equipment, where Standard Elektrik hopes to make its deepest mark. The company faces stiff competition, analysts say, from such big new alliances as the venture between Italy's Olivetti and the American Telephone and Telegraph Company, and from industry stalwarts, such as the International Business Machines Corporation.

A version of this article appears in print on April 29, 1985, on Page D00008 of the National edition with the headline: ITT'S KEY WEST GERMAN UNIT

HISTORY OF Standard Elektrik Lorenz AG IN GERMAN:

Die Standard Elektrik Lorenz AG (heute Alcatel-Lucent Deutschland AG) ist ein Unternehmen der Nachrichtentechnik (früherer Slogan: SEL – Die ganze Nachrichtentechnik) mit Hauptsitz in Stuttgart. Zur Nachrichtentechnik zählen auch Informations- und Kommunikationstechnik, Telekommunikationstechnik (SEL war für die Röchelschaltung bekannt) und früher Fernmeldetechnik oder Schwachstromtechnik. Einen weiteren Geschäftsbereich hatte das Unternehmen in der Bahnsicherungstechnik, so wurden für die Deutsche Bundesbahn Relaisstellwerke und elektronische Stellwerke mit den dazugehörigen Außenanlagen (Signale, Gleisfreimeldeanlagen, Weichenantriebe) sowie die Linienzugbeeinflussung entwickelt und gebaut, welche auch bei ausländischen Bahnen Abnehmer fanden. Der Bereich gehört seit 2007 als Thales Transportation Systems GmbH (seit 02.2011 vorher Thales Rail Signalling Solutions GmbH) zum Thales-Konzern. Die bereits 1998 ausgegliederten Bereiche Alcatel Air Navigation Systems und SEL Verteidigungssysteme sind ebenfalls heute in Thales Deutschland beheimatet.
Fernseher Illustraphon 743 von 1957
„Goldsuper Stereo 20“ (1961)
Das Flaggschiff der erfolgreichen Schaub-Lorenz Kofferradios der sechziger Jahre: Touring 70 Universal
Erster Digitalfernseher der Welt (1983)

Bis 1987 gehörte SEL zusammen mit anderen auf dem Sektor Telekommunikation in anderen Ländern tätigen Schwesterfirmen zum US-amerikanischen Mischkonzern International Telephone and Telegraph (ITT). ITT verkaufte die Aktien-Mehrheit an den ITT-Telekommunikationsfirmen an die französische Compagnie Générale d’Electricité (CGE), die nach der Zusammenfassung mit den eigenen Telekommunikationsaktivitäten daraus die Alcatel N.V. bildete.

Die Standard Elektrik Lorenz AG wurde 1993 in Alcatel SEL AG umbenannt. Die Aktienmehrheit liegt mit über 99 % bei der Alcatel. Mit der Fusion von Alcatel und Lucent zu Alcatel-Lucent am 1. Dezember 2006 und der Neu-Firmierung beider Unternehmen in Deutschland zur Alcatel-Lucent Deutschland AG entfiel der Zusatz SEL.


Geschichte

Die beiden Stammfirmen des Unternehmens, die Mix & Genest AG und die Telegraphenbauanstalt von C. Lorenz, wurden 1879 bzw. 1880 gegründet. Das erste Patent von Mix & Genest datiert von 1883, das erste Patent von C. Lorenz ist aus dem Jahr 1902.

Das Unternehmen Mix & Genest war wesentlicher Teil der Standard Elektrizitäts-Gesellschaft (SEG), in die auch die Süddeutsche Apparatefabrik (SAF), die 1875 von F. Heller als "Friedrich Heller, Fabrik Elektrotechnischer Apparate" gegründet wurde, integriert wurde. Der technische Schwerpunkt von Mix & Genest bzw. SEG sowie der C. Lorenz AG war der klassischen Fernmelde- bzw. Funktechnik zuzuordnen. Die C. Lorenz AG baute in den 1920er und 1930er Jahren Großsender für den neu gegründeten Rundfunk.

1930 übernahm die International Telephone and Telegraph Company (ITT) die Aktienmehrheit der Mix & Genest AG und der C. Lorenz AG.

Die C. Lorenz AG positionierte sich mit der Übernahme der G. Schaub Apparatebau-Gesellschaft mbH im Jahr 1940 in der Entwicklung und Herstellung von Rundfunkempfängern. Ab dem Jahr 1950 wurden alle Geräte bei Schaub in Pforzheim gefertigt. 1952 wurde das Typenprogramm beider Unternehmen verschmolzen und der Lorenz-Radio-Vertrieb in die Firma Schaub integriert. Ab 1955 wurden die Geräte unter dem Namen Schaub-Lorenz vertrieben.

1956 wurde das Unternehmen SEG in Standard Elektrik AG umbenannt. Ebenfalls 1956 wurde ein Kabelwerk gegründet. Wesentlicher Motor für das 1957 gegründete Informatikwerk war Karl Steinbuch, der von 1948–1958 dem Unternehmen, zuletzt als Technischer Direktor und Leiter der Zentralen Forschung, angehörte.

1958 erfolgte die Vereinigung der Standard Elektrik AG mit der C. Lorenz AG zur Standard Elektrik Lorenz AG (SEL).

Die Standard Elektrik Lorenz AG übernahm 1961 die Graetz KG. Die Firmenteile Schaub-Lorenz und Graetz waren zusammen mit einem Bildröhrenwerk Bestandteil der Unternehmensgruppe Audio Video der SEL AG, die 1979 als Audio-Video-Elektronik in die ITT ausgegliedert wurde. Die Produkte, die unter anderem Fernsehgeräte, Radios, Autoradios, Kassettenrecorder, Weltempfänger und Lautsprecherboxen umfassen, wurden fortan unter dem Namen ITT Schaub-Lorenz vertrieben.

Versuche, auf dem neuen Gebiet der Raumfahrt-Elektronik Fuß zu fassen, waren auf folgende Produkte beschränkt:

* AZUR: Telemetrie/Telekommandogeräte
* Spacelab: Datenerfassung/Kommandoterminal.

SEL entwickelte zu Beginn der 1970er Jahre das Präzisionsanflugverfahren SETAC. Dieser Unternehmensbereich wurde im Jahre 1987 von der finnischen Firma Nokia übernommen.

1976 hatte SEL ein Grundkapital von 357 Mio. DM bei 33.000 Beschäftigten und einem Umsatz von 2,6 Mrd. DM.

1983 stellte S E L auf der Internationalen Funkausstellung Berlin 1983 mit dem ITT Digivision den weltweit ersten Fernseher mit digitaler Signalverarbeitung vor.

2003 wurden die Markenrechte am Namen Schaub Lorenz an die italienische General Trading SpA verkauft. Die neugegründete Schaub Lorenz International GmbH vertreibt seitdem unter dem alten Markennamen Schaub-Lorenz importierte Konsumelektronik aus dem unteren Preisbereich.


References:
 

Demerjian, Dave (25 October 2007). "As Skies Grow Crowded, FAA Preps Air Traffic Control 2.0". Wired.com. Archived from the original on 14 June 2013. Retrieved 25 May 2013.
"ITT Corporation 2017 Annual Report Form (10-K)" (XBRL). United States Securities and Exchange Commission. February 14, 2018.
"ITT Corporation 2016 Annual Report Form (8-K)" (XBRL). United States Securities and Exchange Commission. February 14, 2017. Archived from the original on March 16, 2017.
"ITT History". ITT Inc. Archived from the original on 2017-08-03. Retrieved 2017-08-02.
"At A Glance | ITT Inc". www.itt.com. Retrieved 2019-01-09.
www.itt.com https://www.itt.com/CMSPages/GetFile.aspx?guid=10cffa55-7c3c-4e27-b649-d0378feddc07. Retrieved 2019-01-09. Missing or empty |title= (help)
"ITT to break itself up, fueling share rally". Reuters. January 12, 2011. Archived from the original on July 1, 2012. Retrieved July 14, 2011.
Jacobs, Karen (July 14, 2011). "UPDATE 1-ITT sets names for planned spin-offs". Reuters. Archived from the original on July 1, 2012. Retrieved July 14, 2011.
Sobel, Robert (2000). ITT: The Management of Opportunity. Beard Books. pp. 35ff.
Macintosh, Norman B.; Paolo Quattrone (2009). Management Accounting and Control Systems. John Wiley and Sons. pp. 155–6.
Ingham, John N. (1983). Biographical dictionary of American business leaders, Volume 1. Greenwood Publishing Group. pp. 62–4.
Sampson, Anthony. The Sovereign State of ITT, Hodder and Stoughton, 1973. ISBN 0-340-17195-2
Garcia Algarra, Javier (2010). "The American influence in Telefónica's public relations strategy during the 20s and 30s" Archived 2013-06-01 at the Wayback Machine, IEEE HISTELCON 2010
AMERICAN VISITS HITLER. Behn of National City Bank Confers With Chancellor in Alps. New York Times, 1933-08-04, "Archived copy". Archived from the original on 2014-03-07. Retrieved 2013-05-16.
»Empfänge beim Reichskanzler«, Vossische Zeitung, Berlin 1933-08-04, Abendausgabe, Seite 3, "Archived copy". Archived from the original on 2014-03-07. Retrieved 2013-05-03.
The Office of Military Government US Zone in Post-war Germany 1946-1949, declassified per Executive Order 12958, Section 3.5 NND Project Number: NND 775057 by: NND Date: 1977
Leidig, Ludwig. Bombshell. sbpra, 2013 ISBN 978-1-62516-346-2
Farnsworth, Emma. "Farnsworth, Philo T. and Elma G." J. Willard Marriott Library, University of Utah. Archived from the original on 14 July 2014. Retrieved 8 July 2014.
"KONI shock absorbers". Archived from the original on 2015-05-18.
International Telephone and Telegraph Corporation Archived 2012-01-22 at the Wayback Machine at Funding Universe
Knippers Black, Jan (1977). United States Penetration of Brazil. The University of Pennsylvania Press. pp. 40–49.
Langguth, A. J. (1979). Hidden Terrors: The Truth about U.S. Police Operations in Latin America. New York: Pantheon Books.
Green, James (2010). We Cannot Remain Silent: Opposition to the Brazilian Military Dictatorship in the United States. Durham and London: Duke University Press. p. 89. ISBN 978-0-8223-4735-4.
Burn Before Reading, Admiral Stansfield Turner, 2005, Hyperion, pg. 99. Also see the article on Humberto de Alencar Castelo Branco. Also see BRAZIL MARKS 40th ANNIVERSARY OF MILITARY COUP Archived 2008-11-20 at the Wayback Machine, National Security Archive, George Washington University. Edited by Peter Kornbluh, 2004.
Ancona, Vincent S. (Fall 1992). "When the Elephants Marched out of San Diego". Journal of San Diego History. San Diego Historical Society. 38 (4). Archived from the original on 2013-07-05.
"ITT: No charges". Time Magazine. June 10, 1974. Archived from the original on 19 October 2012. Retrieved 24 October 2012. United States and American History: 1972 Archived 2007-03-18 at the Wayback Machine at trivia-library.com
Hinchey Report Archived 2009-10-20 at the Wayback Machine at US Dept. of State
Stout, David (January 30, 2003). "Edward Korry, 81, Is Dead; Falsely Tied to Chile Coup". The New York Times. Archived from the original on May 12, 2013. Retrieved May 5, 2010.
The Pinochet File: How U.S. Politicians, Banks and Corporations Aided Chilean Coup, Dictatorship Archived 2015-09-12 at the Wayback Machine. Democracy Now! September 10, 2013.
Montgomery, Paul L. (September 29, 1973). "I.T.T. OFFICE HERE DAMAGED BY BOMB; Caller Linked Explosion at Latin-American Section to 'Crimes in Chile' I.T.T. Latin-American Office on Madison Ave. Damaged by Bomb Fire in Rome Office Bombing on the Coast Rally the Opponents". The New York Times. Archived from the original on May 12, 2011. Retrieved May 5, 2010.
Ayers, Bill. Sing a Battle Song: The Revolutionary Poetry, Statements, and Communiques of The Weather Underground
Wasserstein, Bruce. Big deal: the battle for control of America's leading corporations
Associated Press (23 November 1997). "Obituary: Harold Geneen, 87; Led ITT's Growth for 18 Years". The New York Times. Archived from the original on 27 March 2016.
Viswanathan, T. Telecommunication Switching Systems and Networks, p.225.
US Patent 4,201,891 at freepatentsonline.com
International Telephone Telegraph Corp at encyclopedia.com
Magnet, Myron; Andrew Evan Serwer (11 November 1985). "IS ITT FIGHTING SHADOWS -- OR RAIDERS?". Fortune. Archived from the original on 29 April 2014.
Chapuis, Robert J.; Joel, Amos E., Jr. "IX-7: "The ITT (now Alcatel) System 12"". 100 Years of Telephone Switching.
"ITT Earnings Decline 33% for 3rd Quarter" Archived 2011-12-24 at Wikiwix, Los Angeles Times, 5 November 1985.
Bartlett, Christopher A.; Ghoshal, Sumantra (2002). Managing Across Borders (2 ed.). Harvard Business School Press. ISBN 978-1-57851-707-7.
ITT Telecom Archived 2016-12-20 at the Wayback Machine, The New York Times, 26 June 1984.
"ITT Makes Sale To Southern Bell" Archived 2016-12-20 at the Wayback Machine, The New York Times, 21 March 1985.
ITT System 12 Archived 2016-09-20 at the Wayback Machine at frankoverstreet.com
Hinman, Catherine."ITT Division In Brevard Will Furlough 60" Archived 2011-12-23 at Wikiwix, Orlando Sentinel, 14 March 1986.
Alcatel-Lucent Timeline Archived 2012-02-03 at the Wayback Machine at alcatel-lucent.com
Alcatel SA Company History Archived 2012-01-22 at the Wayback Machine at Funding Universe
"ITT Accepts $3.6 Billion Alcatel Sale" Archived 2016-03-06 at the Wayback Machine, The New York Times, 4 March 1992.
"Archived copy". Archived from the original on 2016-09-08. Retrieved 2016-09-13. ITT Tech closes its doors, blaming ‘unconstitutional’ US sanctions
"COMPANY NEWS; Metromedia Deal For 2 ITT Units" Archived 2017-12-19 at the Wayback Machine, The New York Times, 16 March 1989.
"Company News; Starwood Lodging in $2.1 Billion Deal with Vnu". The New York Times. 1997-12-19. ISSN 0362-4331. Retrieved 2018-05-29.
Webpage at ITTESI.com Archived October 22, 2006, at the Wayback Machine
Nunez, Michael (September 6, 2016). "ITT Tech Is Officially Closing". Gizmodo. Archived from the original on September 6, 2016. Retrieved September 6, 2016.
Center, Arbitration and Mediation. "WIPO Domain Name Decision: D2001-0166". Archived from the original on 2001-06-10.
Lindsey, Sue. "ITT Fined $100M for Illegal Tech Exports"^{[dead link]}, Associated Press, March 27, 2007.
Cullen, Drew. "ITT Fined for Illegal Exports" Archived 2011-02-24 at Wikiwix, The Register, 27 March 2007.
"Consent Agreement, 2007: ITT Corporation" Archived 2009-10-10 at the Wayback Machine U.S. State Department, 2007.
"ITT fined $100 million for illegal exports". CNN. 27 March 2007. Archived from the original on 28 March 2010. Retrieved May 5, 2010.
"ITT Corp. Acquires EDO in $1.7B Deal". Archived from the original on 2016-08-17.
"Archived copy". Archived from the original on 2011-09-23. Retrieved 2009-01-03. 67 (block): The International Telephone and Telegraph Building, erected in 1928 by Garment District developer Abraham Lefcourt as the Lefcourt Exchange Building, was almost immediately bought by ITT--which expanded the building to take over the whole block by 1930.
Holusha, John. "Commercial Property /75 Broad Street; Turning Buildings Into Telecommunications Hubs" Archived 2016-03-16 at the Wayback Machine, The New York Times, 10 October 1999.
http://www.thecityreview.com/parkave.html. Archived from the original on 2012-01-20. Missing or empty |title= (help)
Deutsch, Claudia H. (21 May 1989). "REFORGING THE 'GENEEN MACHINE'". The New York Times. Archived from the original on 28 August 2016.
"International Telephone & Telegraph ITT Information and History". Archived from the original on 2016-03-29.
"Radio Tower Demolished". The New York Times. 5 April 1996. Archived from the original on 22 July 2010. Retrieved 2010-07-23.
"ITT Avionics Gets $19.6M Air Force Pact". Bergen Record. 19 September 1991. Archived from the original on 18 May 2013. Retrieved 2010-07-23.
(August 20, 2004.) "ITT Industries Receives Contract for $24.9 Million." Archived 2012-04-20 at the Wayback Machine Impeller.net Archived 2011-11-01 at the Wayback Machine. Accessed November 2011.
(in German) https://blogger.googleusercontent.com/img/b/R29vZ2xl/AVvXsEhnKTQ77fJC1zPOqLucj9Ld9DOZoteOPpCdq21SAyBjdDgHDWGgFfxgS6C__apBgbZyyouh4vXtL2fUJUK8DWbrPlzriwCroyMR-ci_t_9Ti3Yf5vGJw-jrBSZV7J8LsyvLEYYfGm61RkUU/s1600/ITT-2805_SLK-AD2.jpg. Archived from the original on 2018-05-01. Missing or empty |title= (help)
"Consola "pong" Tele-Match (versión con paddle) (1977)". retroordenadoresorty.blogspot.it (in Spanish). Archived from the original on 1 May 2018. Retrieved 14 February 2018.
"ITT DIGIVISION 3447 OSCAR YEAR 1986". Obsolete Technology Tellye. Retrieved 14 February 2018.
"Kellogg Switchboard & Supply Co". Dictionary of Leading Chicago Businesses. Archived from the original on 18 August 2015. Retrieved 15 February 2018.
"Über ITT - ITT". www.itt-deutschland.de (in German). Archived from the original on 17 October 2017. Retrieved 15 February 2018.
"Nokia Announces Final Sale of its Television Manufacturing Business - Nokia". Nokia. Archived from the original on 2017-07-29.
"Über Karcher - ITT". www.itt-deutschland.de (in German). Archived from the original on 22 December 2016. Retrieved 14 February 2018.

--------------------------------------------------------------------------------------------------------------------------------------------------------------