KENNEDY (ELCIT) KB20 ELECTRON YEAR 1974.

The KENNEDY (ELCIT) KB20  ELECTRON  is a 20 inches (50cm) B/W television with 8 programs preselection tuning keyboard and potentiometric search in a drawbar.

The mechanical turret approach to television tuning has been used almost exclusively for the past 60 years. Even though replete with the inherent disadvantages of mechanical complexity, unreliability and cost, such apparatus has been technically capable of performing its intended function and as a result the consumer has had to bear the burdens associated with the device. However, with the " recent "  Broadcast demands for parity of tuning for UHF and VHF channels, the increasing number of UHF and cable TV stations have imposed new tuning performance requirements which severely tax the capability of the mechanical turret tuner. Consequently, attempts are now being made to provide all electronic tuning to meet the new requirements.

 One " " new " " tuning system currently being incorporated in some television receivers uses a varactor tuner which overcomes some of the disadvantages of mechanical turret tuner by accomplishing tuning electronically. As the name indicates, the heart of such a tuner is a varactor diode which is used as a capacitive tuning element in the RF and local oscillator sections. In this system, channel selection is made by applying a given reverse bias voltage to the varactor to change its electrical capacitance. The channel selection biasing can be performed by mechanically or electrically switching approximately 5 or many more preset potentiometers. The problem with such arrangement is that it quite seriously limits the number of channels available to the consumer. Additionally, it suffers from the drawback that all potentiometers require adjusting for the desired channels. The VHF channels are usually factory adjusted while the six UHF channels require on-location adjustment. Moreover, using this arrangement, the only indication--during adjustment--of which channel is selected is by station identification.
Springs component in old tv's tuner :
Most old televisions tuning mechanisms were incorporating coil springs in one form or another for various functions. They can be of the compression type which are wound with spaces between adjacent turns and are intended to be squeezed under pressure : when released they expand to their original form. The mounting springs under record-player turntable units are examples of this type. Alternatively the spring can be of the expanding variety. The coils are wound closely together with adjacent turns touching. The applied tension tends to pull them apart and they exert a contracting force to counteract this and pull the linked components together. In the majority of applications this type is used. Springs often become damaged by being over stretched, or the end loop breaks. More frequently the spring simply becomes detached and disappears. Thus the engineer is faced with the task of finding and fitting a replacement. While it is possible to apply to the makers of the equipment for the right spring this involves delay and of course there is always the problem of identifying the right one out of the many used in the particular mechanism. For this reason many engineers find it more convenient to make their own replacements.

Making a Coil Spring: The operation was quite simple, the equipment needed being a wheelbrace, vice, selection of long screwdrivers with varying diameter shanks and a supply of piano wire of various gauges. The wheelbrace is mounted horizontally in the vice with the wheel uppermost and a screwdriver chosen and inserted into the chuck with the blade foremost. This serves as a mandrel on which the spring can be wound. Because a spring expands slightly in diameter after it is wound the diameter of the screwdriver shank should be a little less than the required inside diameter of the spring. One end of the piano wire should be inserted in the chuck and secured to prevent it coming free. The wheel is then slowly turned and the wire taken up around the screwdriver shank. Keep the wire taut and pull it backward (see Fig. 1) toward the chuck at an angle which keeps the adjacent turns together but does not make a turn ride over the top of its predecessor. When the spring has reached the required length cut the wire and remove the springand screwdriver from the chuck.
As an aid in determining the size of the spring required-especially if the original is lost and there is no pattern to make a comparison with-here are a few observations on the characteristics of coil springs as determined by their dimensions.
Properties of Coil Springs: There are two main properties of a spring, the length to which it can be expanded in comparison to its closed length and its tension or strength in the expanded state. If a coil spring is expanded too far its coils will not return to their original position and the spring is said to be stretched. The amount that a spring can be expanded without becoming stretched is governed by the number of turns and the diameter. The greater the number of turns the less each one has to deviate from its resting position for the complete spring to reach a particular length. Also the greater the diameter the smaller the strain and therefore the more the spring can be expanded. The strength of a spring is related to the gauge of wire and the diameter. A heavy gauge will obviously give greater tension than a lighter one but also a spring with a large diameter will exert less force than a smaller one because as we have seen there is less strain when it is expanded. More force is exerted when the spring is well expanded than when it is nearly closed. If therefore we need a spring that is strong and will stretch a long way we need a large number of turns but not so many that the spring is too long in its closed position. It needs to be of fairly large diameter but as this will make it weaker we must compensate by using a heavy gauge of wire. A weak spring with a long stretch is easily made with thinner wire and a large diameter while a strong spring with a short stretch need have few turns and small diameter. So the various factors are interdependent and although spring design can be quite an exact art-by varying the various parameters-something suitable for the job can usually be made up by judicously estimating the size from the foregoing principles. If a spring has become stretched nothing can be done to restore it by squeezing it up as it has now become a compression spring and the expanded state is its normal one. Rather than winding a completely new spring however the old one can be unwound on a wheelbrace-by reversing the winding process and then rewound tightly. Proper unwinding is essential, not just pulling the spring out straight, because this will produce kinks.
Leaf Springs: From coil springs we turn to leaf springs. These were used as contacts in tuner units and are also were used in the press  button channel selector of the Philips colour TV range and other fabricants. To make a positive contact the leaf spring must be tensioned just right. In the case of the turret tuner the leaf must be so sprung that the contacting stud moves it about a tenth of an inch away from the resting position. If as sometimes happens contact is made without much movement of the leaf there will be little if any pressure and the contact will very likely be intermittent. If on the other hand the leaf is adjusted too far forward it may be caught by the edge of the coil biscuit and crumpled when the turret is rotated.
The set is a hybrid chassis featured  type and it has 4 tubes in power circuits parts.

These sets were collocated in the cheap market allowing so even affordable television sets without concurrence of more expensive other models from bigger brands.

This kind of tv sets are rare by the fact that very few of them were sold.

(Television set kindly donated to me by Marshal Elia Z.)

KENNEDY / ELCIT was a Radio fabrication industry which in the 1953 joined Visiola to produce television sets and other domestic appliances such washing machines and fridge.


ELCIT Was even proprietary of the MAGNADYNE brand which WAS a radio and Television well known brand.

In the 1960 the society was joined and aquired by SEIMART because of a market contraction which landed to GEPI a new society which re - founded ELCIT.

The conglomerate of ELCIT AND SEIMART which was a joint developed by GEPI a government special system invented to "save" industry with "some" difficulties (!!!) was unified.


NOTE:
SEIMART and its conglomerate was even proprietary of brands like:

ETERPHON KENNEDY RAYMOND VISIOLA and DAMAITER.

and

MAGNADYNE +

KENNEDY

and;

The following sub brands were even from the group but were specialized in other fields like
preparing materials, developing parts and other jobs like domestic appliances and even CRT TUBE manufacutring.

NEOHM was a resistor fabricant and was part of the group

Basically the industry group was completely autonomous exept for semiconductors which were coming from other well known brands and manufacturers.

RADSET

VISSET

NEOHM was a resistor fabricant and was part of the group

VITAUT
STAMPLAST
STAMFER

BOBSET
CIRSTA
FRIMAX

MOBFER P

TRAMAX
FINPLAST
VALVEX (CRT TUBES AND TUBES)

ELCIT died in 1998 by typically Italian Industry Destroy culture (and , of course, chinese and turkish (super CRAP) basar !) and all workers and employee landed.......... on the street !!!!!!!!!!!!!

R.I.P. ITALY !

KENNEDY (ELCIT) KB20 ELECTRON CHASSIS 687.301.710 + 687.303.950/D INTERNAL VIEW.

The KENNEDY (ELCIT) KB20  ELECTRON  CHASSIS 687.301.710 + 687.303.950/D  is developed on 2 boards.

- Left signal board is based around semiconductors Ics and discretes.

- Bottom Horizontal board contains all power parts.

The chassis is hybrid.

 The CHASSIS TECHNOLOGY is based on ASIC'S which are:TBA311A17 TBA120SQ  and lots of discretes.





TBA 311 TV SIGNAL PROCESSING CIRCUIT


The TBA311 is a monolithic integrated circuit in a 16-lead clual in-line or quad in—Iine
plastic package. It is intended for use as signal processing circuit for black and
white and colour television sets.
The circuit is designed for receivers equipped with tubes or transistors in the deflection
and video output stages, and with PNP or NPN transistors in the tuner and NPN in
the IF amplifier.
Only signals with the negative modulation can be handled by the circuit. The circuit
is protected against short circuit between video output and GND. The TBA 311 includes:




0 VIDEO PREAMPLIFIER with EIMITTER FOLLOWER OUTPUT
0 GATED AGC for VIDEO» IF AMPLIFIER and TUNER
0 NOISE INVERTER CIRCUIT for GATING AGC and SYNC. PULSE SEPARATOR
o HORIZONTAL SYNC. PIULSE SEPARATOR
0 VERTICAL SYNC. PULSE SEPARATOR
0 BLANKING FACILITY for the VIDEO AMPLIFIER.

TAA611-A12 - Dual BTL power audio amplifier

All ICS circuits were made by:

SGS is Società Generale Semiconduttori - Aquila Tubi E Semiconduttori (SGS-ATES, "Semiconductor General Society - Tubes and Semiconductors Aquila"), later SGS Microelettronica, a former Italian company now merged into STMicroelectronics

SGS Microelettronica and Thomson Semiconducteurs were both long-established semiconductor companies. SGS Microelettronica originated in 1972 from a previous merger of two companies:

• ATES (Aquila Tubi e Semiconduttori), a vacuum tube and semiconductor maker headquartered in the Abruzzese city of l'Aquila, who in 1961 changed its name into Azienda Tecnica ed Elettronica del Sud and relocated its manufacturing plant in the outskirts of the Sicilian city of Catania
• Società Generale Semiconduttori (founded in 1957 by Adriano Olivetti).

TUBES USED:


- PL504
- PY88
- PCL805
- PCF802

How AFC Circuit Works in B/W Analog Television Receiver:

Push-Button tuning on u.h.f. while being very convenient often leaves a margin of mistuning, especially after some wear and tear has occurred on the mechanism. Even dial tuning can lead to errors due to the difficulty many people experience in judging the correct point. Oscillator drift due to temperature changes can also cause mistuning. Automatic frequency control (a.f.c.) will correct all these faults. The vision carrier when the set is correctly tuned on u.h.f. is at 39.5MHz as it passes down the i.f. strip. Thus if at the end of the i.f. strip a discriminator tuned circuit is incorporated centred on 39.5MHz the discriminator output will be zero at 39.5MHz and will move positively' one side of 39.5MHz and negatively the other as the tuning drifts. This response is shown in Fig. 1.

If the tuning is not correct then the discriminator output is not zero and if this output is applied to change the reverse bias on a tuning diode mounted in the oscillator section of the u.h.f. tuner it will correct most of the error. Tuning, varicap or varactor diodes-to give them a few of their names-are junction diodes normally operated with reverse bias but not sufficient to bias them into the breakdown region in which zener diodes operate. The greater the reverse bias the lower their capacitance: a typical curve, for the PHILIPS BB105 or STC BA141 tuning diode, is shown in Fig. 2. All diodes exhibit this basic type of characteristic but special diodes have to be used for u.h.f. because they must not introduce any excessive loss into the tuned circuits they control. In other words, just as a coil has to have a good Q so does a varicap diode. Normally, we don't worry about the Q of a capacitor as it is usually very good. However, a tuning diode is not a true capacitor. It has, for example, leakage current so the Q of the diode is a factor which has to be considered. The diode manufacturer however will have considered these points and if you buy a diode specified for u.h.f. use you will have no trouble. These points have been mentioned to clear up any misunderstandings and to show why any old diode won't do.

Basic AFC System
To return to our TV set, if the oscillator frequency is too high then the vision carrier frequency will also be too high and in the simple arrangement shown in Fig. 3 the discriminator will give a negative signal to decrease the bias on the tuning diode thus increasing its capacitance and in turn reducing the oscillator frequency and correcting the error. Note that in this diagram the reverse bias on the diode is applied to its cathode. It is therefore positive with respect to ground so that a negative signal from the discriminator will reduce the positive voltage on the diode thus reducing its bias and increasing its capacitance. In this arrangement the diode is biased somewhere near the mid point of its characteristic by the positive d.c. bias fed into one side of the discriminator. The discriminator thus adds to or subtracts from this d.c. bias.

AFC Loop Gain:
The amount by which the error is reduced depends on the gain of the circuit. An estimate of the gain required must first be made by guessing how much error is likely to be given by your push -buttons or hand tuning: 1MHz would be an outside figure as a tuning error of that magnitude would produce a very bad picture of low definition in one direction and badly broken up in the other. This error should be reduced to about 100kHz to be really unnoticeable, indicating a required gain of ten. In fitting a.f.c. to an existing set some measure- ments should be done as an experiment before finally deciding on the circuit gain. The first thing to do is  to add the suggested discriminator to the i.f. strip. As the circuit (Fig. 4) shows a Foster -Seeley type discriminator is used and with the coils specified and the driver circuit shown it should give ±4V for 0.5MHz input variation.

EXAMPLE of Circuit Description:
The driver stage Tr1 takes a small sample signal from the i.f. strip but this should be large enough to drive Tr1 into saturation. That is to say Tr1 is a limiter stage so that the signal amplitude applied to the discriminator coil L2 stays constant over the normal range of signal levels. Trl is biased at approximately 7mA which, according to the original report ("Simple a.f.c. system for 625 -line TV receivers" by P. Bissmire, PHILIPS Technical Communications, March, 1970), gives the best limiting performance. C1, R14 and R3 damp the stage to prevent oscillation. C2 decouples the power feed and should be close to the circuit. The coil former and can are the normal ones used for TV sets and so should be easily obtainable: the former diameter is 5mm. and length 40mm. and winding details are given in Fig. 5.

The invention being thus described, it will be obvious that the same may be varied in many ways. Such variations are not to be regarded as a departure from the spirit and scope of the invention, and all such modifications as would be obvious to one skilled in the art are intended to be included within the scope of the developed apparates both tubes or transistors.

Thermionic tubes, also known as vacuum tubes or electron tubes, are electronic devices that were widely used in the early 20th century as amplifiers, oscillators, and rectifiers in electronic circuits. These devices are made of a sealed glass envelope that contains a vacuum, and they rely on the flow of electrons from a heated cathode to a positively charged anode to produce a current. The cathode is typically made of a material that has a low work function, such as tungsten or thoriated tungsten, and is heated by a filament to emit electrons through a process called thermionic emission. The anode, on the other hand, is usually made of a metal that can withstand high temperatures and is shaped to form a series of plates or grids that control the flow of electrons.

Vacuum tubes have always been used to control the flow of electricity through electronic components.

These devices became a key component of electronic circuits for the first half of the twentieth century. They were crucial to the development of radio, television, radar, sound recording and reproduction, long-distance telephone networks, and analog and early digital computers. Although some applications had used earlier technologies such as the spark gap transmitter for radio or mechanical computers for computing, it was the invention of the thermionic vacuum tube that made these technologies widespread and practical, and created the discipline of electronics.

Of course, there must be a hard vacuum (about one millionth of normal air pressure at sea level) inside the bulb (modern light bulbs often contain gas), otherwise gas molecules would block the movement of electrons. To preserve this hard vacuum, after a thermionic valve has had all the air pumped out of it, a "getter" made of reactive metal such as barium is fired by means of an electrical discharge and/or RF induction heating through the glass wall, which creates a silvery coating on the inside of the glass that will absorb any remaining gas molecules, including ones that can be released from the valve materials.

Classification
One classification of thermionic vacuum tubes is by the number of active electrodes. A device with two active elements is a diode, usually used for rectification. Devices with three elements are triodes used for amplification and switching. Additional electrodes create tetrodes, pentodes, and so forth, which have multiple additional functions made possible by the additional controllable electrodes.
Other classifications are:

•  by frequency range (audio, radio, VHF, UHF, microwave)
•  by power rating (small-signal, audio power, high-power radio transmitting)
•  by cathode/filament type (indirectly heated, directly heated) and warm-up time (including "bright-emitter" or "dull-emitter")
•  by characteristic curves design (e.g., sharp- versus remote-cutoff in some pentodes)
•  by application (receiving tubes, transmitting tubes, amplifying or switching, rectification, mixing)
•  specialized parameters (long life, very low micro phonic sensitivity and low-noise audio amplification, rugged or military versions)
•  specialized functions (light or radiation detectors, video imaging tubes)

 tubes used to display information (Nixie tubes, "magic eye" tubes, vacuum fluorescent displays, CRTs)
Tubes have different functions, such as cathode ray tubes which create a beam of electrons for display purposes (such as the television picture tube)

Within the space of a mere fourteen years, television has developed from a scientific toy to a public service which daily provides entertainment and instruction to hundreds of thousands of people on both sides of the Atlantic. The skepticism which originally prevailed concerning the possibility of exploiting the new art has given place to complete confidence in both technical and commercial circles, and television now supports a thriving industry which is assured, by plans already well advanced, of rapid growth and development not only in Great Britain and in the U.S.A. but also in European countries which, s o far, have not instituted a television service.

Many problems had to be solved before television could been brought to its state of perfection at which, from the technical point of view, mass popularity can be assured. But mass popularity depends not only upon technical perfection but also upon the availability of receivers of good performance at low cost. The production of such equipment was, of course, the task of the set maker. In the design of high-quality television receivers, the tubes employed played an important part.

+ Tubes originally produced for normal broadcast reception, however efficient they may be for that purpose, are not necessarily the most suitable for television reception. Indeed, such have been  developments that it is safe to say that unless tubes which have been specially developed for television service are employed, receivers of the highest performance combined with low cost cannot be realized.

HERE below the Datasheets Manuals of the  Thermionic tubes used in the TV SET in the article:KENNEDY (ELCIT) KB20  ELECTRON  CHASSIS  687.301.710 + 687.303.950/D.

 

 
- The EHT Output is realized with a selenium rectifier.

The EHT selenium rectifier which is a Specially designed selenium rectifiers were once widely used as EHT rectifiers in television sets and photocopiers. A layer of selenium was applied to a sheet of soft iron foil, and thousands of tiny discs (typically 2mm diameter) were punched out of this and assembled as "stacks" inside ceramic tubes. Rectifiers capable of supplying tens of thousands of volts could be made this way. Their internal resistance was extremely high, but most EHT applications only required a few hundred microamps at most, so this was not normally an issue. With the development of inexpensive high voltage silicon rectifiers, this technology has fallen into disuse.A selenium rectifier is a type of metal rectifier, invented in 1933. They were used to replace vacuum tube rectifiers in power supplies for electronic equipment, and in high current battery charger applications.

A conventional selenium rectifier consists of a metal plate, which acts as the rectifier base electrode, upon one side of which there are deposited, usually by evaporation techniques, layers of selenium with either a halogen additive, such as chlorine, or doped with a metal such as gallium or indium, or both an additive and a dopant. These layers of selenium may be sandwiched with relatively thin layers of various metals such as nickel between the selenium and the base electrode. The counter electrode is generally an alloy such as a cadmium tin alloy. Rectification takes place in a barrier layer which is adjacent the counter electrode. Such rectifiers are reliable but the evaporation apparatus is costly to install and maintain.

SUMMARY OF THE INVENTION
It is an object of the present invention to provide a selenium rectifier, in which the barrier layer constituted by the amorphous selenium is adjacent the base electrode rather than the counter electrode, by electrophoretically depositing the selenium layers. The electrophoretic deposition of selenium is a relatively rapid process compared with evaporation techniques, and does not require costly apparatus.
According to a broad aspect of the invention, there is provided a selenium rectifier comprising a metal plate base electrode; at least one metal layer deposited on one surface of said metal plate, said metal layer consisting of a metal different than that of said metal plate; a first layer of amorphous selenium on said at least one metal layer; a second layer of selenium containing a first halogen additive, said second layer deposited on said first layer; a third layer of selenium containing a second halogen additive and a metallic dopant, said third layer deposited on said second layer; and a metal counter electrode layer deposited on said third layer.

The photoelectric and rectifying properties of selenium were observed by C. E. Fitts around 1886 but practical rectifier devices were not manufactured routinely until the 1930s. Compared with the earlier copper oxide rectifier, the selenium cell could withstand higher voltage but at a lower current capacity per unit area.