SABA ULTRACOLOR T67R52 TELECOMMANDER CHASSIS R-110 INTERNAL VIEW.

Right side
Supply with Step-Up line synchronized (Supply is 80 Volt converted to 135 Volt)

Synchronization

Line deflection output (Telefunken BU208) EHT + Tripler + E/W Correction.

- Left side

Signal Processing / Video with TDA3300 (MOTOROLA)

Frame deflection with TEA1020SP (Thomson)

Tuner + IF VIDEO AND SOUND BOARD

This chassis runs cold without particularly hot parts. It's higly reliable and durable.

It's power supplyed by a separation transformer (see picture) wich provides all mains voltages for the set then these are converted where needed by line synch SMPS stabilized switching circuitry to supply the main parts of the receiver (Deflections and Video).

Probabily on of the best chassis made by SABA During the transition to THOMSON.
We can see a discrete level of integration here and we are in 1981 !!!!

Indeed you can find this Chassis even in some NORDMENDE Tellye called F9.

This pictured here is made by SABA in THOMSON Transition (See code Style Numbers)




- VIDEO CHROMA PROCESSING WITH TDA3300 (MOTOROLA)




TDA3300 3301 TV COLOR PROCESSOR
The Decoder IC The centre -piece of the decoder is the Motorola TDA3300B i.c. which carries out all the luminance and U V Inputs from PAL delay line 9V Frequency nlyv Z 2RV2 100k chroma signal processing required. Features of this 40 -pin chip include: (1) Automatic black -current control via feedback from the RGB output circuits. (2) Peak beam current limiting to prevent blooming on highlights - in addition to the normal beam current limit- ing action. (3) Separate R, G and B input pins for the injection of teletext/data signals (or on -screen display of the channel number with frequency synthesis tuning). These signals can be varied by means of the user brightness and con- trast controls. (4) Low dissipation - about 600mW. (5) By adding a small adaptor panel with a TDA3030A SECAM-to-PAL converter i.c. during production the receiver is given multistandard (PAL, SECAM and NTSC-4.43) capability.

A block diagram of the TDA3300B i.c. is shown in Fig. 3. As with the better known TDA3560 single -chip decoder, both the chroma and the burst pass through the chroma delay line. The U output from this enters the TDA3300B at pin 8, passing to the U detector and to the burst detector. The latter is part of a phase -locked loop, the detector's output being applied via an H/2 (half-line frequency) switch to the 4.43MHz voltage -controlled crystal oscillator. The 4.43MHz reference oscillator's output is applied for PAL switching, and to the U detector via a voltage -controlled 90° phase shifter. This shifter is under the control of the 90° detec- tor which compares its output with the oscillator's output coming via the PAL switch: when the phase shift is cor- rect, the output from the 90° phase detector is zero. The combined effect of the two H/2 switches in the reference oscillator control loop - the two shown on the right-hand side - cancels phase detector offsets. The outputs from the U and V detectors include burst "flag" pulses which are used for a.c.c., ident and colour -killing - there are two colour -killing actions. RGB Output Stages The RGB output stages are of the class AB type and incorporate extra circuitry for c.r.t. black -current sampl- ing and beam limiting. Fig. 4 shows the red output stage. Under most conditions transistor 2TR1 acts as a class A amplifier, driving the tube's cathode via 2D5 and 2TR7. A high -value collector load resistor (2R33) is used to reduce the dissipation in 2TR1. The stage gain is set by the ratio of 2R40 and 2R36 to 2R25 and 2RV3, the latter setting the drive level. For good transient response it's necessary for the tube/base capacitance to be rapidly charged/discharged in accordance with the signal swings. There is no problem when 2TR1 is being driven from off to on, since the capacitance is discharged rapidly via 2D5 and 2TR1. When 2TR1 is driven from on to off however 2D5 will become reverse biased. Under these conditions 2TR4 acts as an emitter -follower so that the capacitance charges rapidly. Black -level stability is critical for good results. As we've 2R46 5k6 2R51 120k 2TR7 BF493S 2C43l Sampling circuit L -J 1k5 Field blanking J Red cathode _Tube input T"and base 810capacitance nlrr Reference Line pedestal blanking Sample -and - hold amplifier-ws switched on rt- Video Urn seen, the TDA3300B chip incorporates circuitry for automatic black -current correction. Making use of this reduces service calls and ensures constant performance despite tube ageing or circuit misadjustment. Feedback is required, and this is provided by the sampling circuit shown in the box with the broken outline. Transistor 2TR7 acts as an emitter -follower between the video output stage and the c.r.t.'s cathode. It's a low leakage type, the components 2C40, 2D10 and 2C43 ensuring that the circuit has negligible effect on the video signal. Since the beam current flows via 2R51, a voltage proportional to the beam current is produced across this resistor. It's fed into the TDA3300B at pin 22. Black -current Control For automatic black -current control the important thing is the small beam current that flows when the tube is biased just above cut off. To enable this current to be sampled, the TDA3300B replaces the video signal with a fixed reference pedestal voltage for a couple of lines at the end of each field blanking period (this pedestal can be seen as a grey line at the top of the picture if the height control's setting is reduced). The sample voltage at pin 22 of the i.c. is fed to one input of a sample -and -hold amp- lifier which is switched on to sample the input for one line only of the reference pedestal period. 2C33 acts as the black -current control reservoir capacitor, holding the charge acquired during the sampling time for the whole field period. This charge is added to the video signal within the i.c., thus maintaining the correct red gun black current. It's interesting to notice that when a set is switched on from cold there's a momentary screen bright -up with flyback lines as the beam current begins to flow. This is because it takes several fields for 2C33 (and the corre- sponding capacitors in the green and blue channels) to charge fully. Since the voltage continuously available across 2R51 is proportional to beam current, it's used within the i.c. for peak beam current limiting during the active line periods. This is in addition to beam current limiting via the con- trast control - and a crowbar trip that operates should the beam current exceed 3mA.
This device will accept a PAL or NTSC composite video signal and output the
three color signals, needing only a simple driver amplifier to interface to the pic-
ture tube. The provision of high bandwidth on-screen display inputs makes it
suitable for text display, TV games, cameras, etc. The TDA3301 B has user con»
trol laws, and also a phase shift control which operates in PAL, as well as NTSC.
0 Automatic Black Level Setup
0 Beam Current Limiting
0 Uses Inexpensive 4.43 MHZ to 3.58 MHz Crystal
0 No Oscillator Adjustment Required
0 Three OSD Inputs Plus Fast Blanking Input
0 Four DC, High Impedance User Controls
0 lnterlaces with TDA33030B SECAM Adaptor
0 Single 12 V Supply
0 Low Dissipation, Typically 600 mW
The brilliance control operates by adding a pedestal to the output
signals. The amplitude of the pedestal is controlled by Pin 30.
During CRT beam current sampling a standard pedestal is
substituted, its value being equivalent tothe value given by V30 Nom
Brightness at black level with V30 Nom is given by the sum of three gun
currents at the sampling level, i.e. 3x20 |.1A with 100 k reference
resistors on Pins 16, 19, and 22.
During picture blanking the brilliance pedestal is zero; therefore, the
output voltage during blanking is always the minimum brilliance black
level (Note: Signal channels are also gain blanked).

Chrominance Decoder
The chrominance decoder section of the TDA3301 B
consists of the following blocks:
Phase-locked reference oscillator;
Phase-locked 90 degree servo loop;
U and V axis decoders
ACC detector and identification detector; .
Identification circuits and PAL bistable; .
Color difference filters and matrixes with fast blanking
Circuits.
The major design considerations apart from optimum
performance were:
o A minimum number of factory adjustments,
o A minimum number of external components,
0 Compatibility with SECAM adapter TDA3030B,
0 Low dissipation,
0 Use of a standard 4.433618 Mhz crystal rather
than a 2.0 fc crystal with a divider.

The crystal VCO is of the phase shift variety in which the
frequency is controlled by varying the phase of the feedback.
A great deal of care was taken to ensure that the oscillator loop
gain and the crystal loading impedance were held constant in
order to ensure that the circuit functions well with low grade
crystal (crystals having high magnitude spurious responses
can cause bad phase jitter). lt is also necessary to ensure that
the gain at third harmonic is low enough to ensure absence of
oscillation at this frequency.

It can be seen that the
necessary 1 45°C phase shift is obtained by variable addition
ol two currents I1 and I2 which are then fed into the load
resistance of the crystal tuned circuit R1. Feedback is taken
from the crystal load capacitance which gives a voltage of VF
lagging the crystal current by 90°.
The RC network in the T1 collector causes I1 to lag the
collector current of T1 by 45°.
For SECAM operation, the currents I1 and I2 are added
together in a fixed ratio giving a frequency close to nominal.
When decoding PAL there are two departures from normal
chroma reference regeneration practice:
a) The loop is locked to the burst entering from the PAL
delay line matrix U channel and hence there is no
alternating component. A small improvement in signal
noise ratio is gained but more important is that the loop
filter is not compromised by the 7.8 kHz component
normally required at this point for PAL identification
b) The H/2 switching of the oscillator phase is carried out
before the phase detector. This implies any error signal
from the phase detector is a signal at 7.8 kHz and not dc.
A commutator at the phase detector output also driven
from the PAL bistable coverts this ac signal to a dc prior
to the loop filter. The purpose ot this is that constant
offsets in the phase detector are converted by the
commutator to a signal at 7.8 kHz which is integrated to
zero and does not give a phase error.
When used for decoding NTSC the bistable is inhibited, and
slightly less accurate phasing is achieved; however, as a hue
control is used on NTSC this cannot be considered to be a
serious disadvantage.


90° Reference Generation
To generate the U axis reference a variable all-pass network
is utilized in a servo loop. The output of the all-pass network
is compared with the oscillator output with a phase detector of
which the output is filtered and corrects the operating point of
the variable all»pass network .
As with the reference loop the oscillator signal is taken after
the H/2 phase switch and a commutator inserted before the
filter so that constant phase detector errors are cancelled.
For SECAM operation the loop filter is grounded causing
near zero phase shift so that the two synchronous detectors
work in phase and not in quadralure.
The use of a 4.4 MHz oscillator and a servo loop to generate
the required 90° reference signal allows the use of a standard,
high volume, low cost crystal and gives an extremely accurate
90° which may be easily switched to 0° for decoding AM
SECAM generated by the TDA3030B adapter.

ACC and Identification Detectors
During burst gate time the output components of the U and
also the V demodulators are steered into PNP emitters. One
collector current of each PNP pair is mirrored and balanced
against its twin giving push-pull current sources for driving the
ACC and the identification filter capacitors.
The identification detector is given an internal offset by
making the NPN current mirror emitter resistors unequal. The
resistors are offset by 5% such that the identification detector
pulls up on its filter capacitor with zero signal.
Identification
See Figure 11 for definitions.
Monochrome I1 > I2
PAL ldent. OK I1 < lg
PAL ldent_ X l1 > I2
NTSC I3 > I2
Only for correctly identified PAL signal is the capacitor
voltage held low since I2 is then greater than I1.
For monochrome and incorrectly identified PAL signals l1>l2
hence voltage VC rises with each burst gate pulse.
When V,ef1 is exceeded by 0.7 V Latch 1 is made to conduct
which increases the rate of voltage rise on C. Maximum
current is limited by R1.
When Vref2 is exceeded by 0.7 V then Latch 2 is made to
conduct until C is completely discharged and the current drops
to a value insufficient to hold on Latch 2.
As Latch 2 turns on Latch 1 must turn off.
Latch 2 turning on gives extra trigger pulse to bistable to
correct identification.

The inhibit line on Latch 2 restricts its conduction to alternate
lines as controlled by the bistable. This function allows the
SECAM switching line to inhibit the bistable operation by firing
Latch 2 in the correct phase for SECAM. For NTSC, Latch 2
is fired by a current injected on Pin 6.
lf the voltage on C is greater than 1.4 V, then the saturation
is held down. Only for SECAM/NTSC with Latch 2 on, or
correctly identified PAL, can the saturation control be
anywhere but minimum.
NTSC Switch
NTSC operation is selected when current (I3) is injected into
Pin 6. On the TDA33O1 B this current must be derived
externally by connecting Pin 6 to +12 V via a 27 k resistor (as
on TDA33OOB). For normal PAL operation Pin 40 should be
connected to +12 V and Pin 6 to the filter capacitor.

4 Color Difference Matrixing, Color Killing,
and Chroma Blanking
During picture time the two demodulators feed simple RC
filters with emitter follower outputs. Color killing and blanking
is performed by lifting these outputs to a voltage above the
maximum value that the color difference signal could supply.
The color difference matrixing is performed by two
differential amplifiers, each with one side split to give the
correct values of the -(B-Y) and -(Ft-Y) signals. These are
added to give the (G-Y) signal.
The three color difference signals are then taken to the
virtual grounds of the video output stages together with
luminance signal.
Sandcastle Selection
The TDA3301B may be used with a two level sandcastle
and a separate frame pulse to Pin 28, or with only a three level
(super) sandcastle. In the latter case, a resistor of 1.0 MQ is
necessary from + 12 V to Pin 28 and a 70 pF capacitor from
Pin 28 to ground.

Timing Counter for Sample Control
In order to control beam current sampling at the beginning
of each frame scan, two edge triggered flip-flops are used.
The output K ofthe first flip-flop A is used to clock the second
tlip-flop B. Clocking of A by the burst gate is inhibited by a count
of A.B.
The count sequence can only be initiated by the trailing
edge of the frame pulse. ln order to provide control signals for:
Luma/Chroma blanking
Beam current sampling
On-screen display blanking
Brilliance control
The appropriate flip-flop outputs ar matrixed with sandcastle
and frame signals by an emitter-follower matrix.

Video Output Sections
Each video output stage consists of a feedback amplifier in A further drive current is used to control the DC operating
which the input signal is a current drive to the virtual earth from point; this is derived from the sample and hold stage which
the luminance, color difference and on-screen display stages. samples the beam current after frame flyback.

BU208(A)

Silicon NPN
npn transistors,pnp transistors,transistors
Category: NPN Transistor, Transistor
MHz: <1 MHz
Amps: 5A
Volts: 1500V
HIGH VOLTAGE CAPABILITY
JEDEC TO-3 METAL CASE.

DESCRIPTION
The BU208A, BU508A and BU508AFI are
manufactured using Multiepitaxial Mesa
technology for cost-effective high performance
and use a Hollow Emitter structure to enhance
switching speeds.

APPLICATIONS:
* HORIZONTAL DEFLECTION FOR COLOUR TV With 110° or even 90° degree of deflection angle.

ABSOLUTE MAXIMUM RATINGS
Symbol Parameter Value Unit
VCES Collector-Emit ter Voltage (VBE = 0) 1500 V
VCEO Collector-Emit ter Voltage (IB = 0) 700 V
VEBO Emitter-Base Voltage (IC = 0) 10 V
IC Collector Current 8 A
ICM Collector Peak Current (tp < 5 ms) 15 A
TO - 3 TO - 218 ISOWATT218
Ptot Total Dissipation at Tc = 25 oC 150 125 50 W
Tstg Storage Temperature -65 to 175 -65 to 150 -65 to 150 oC
Tj Max. Operating Junction Temperature 175 150 150 °C



SABA ULTRACOLOR T67R52 TELECOMMANDER CHASSIS R-110 Switching regulator power supply device combined with the horizontal deflection circuit of a television receiver which it supplies

Step-up switching regulator power supply device comprising, connected between the poles of a rectifier circuit supplied by an isolating voltage step-down transformer and loaded by a first filter capacitor, and inductance and the collector-emitter path of a first switching transistor of NPN type, a first diode whose anode is connected to the junction of the inductance and to the collector of said transistor and whose cathode is connected to a second filter and storage capacitor supplying a voltage at its output which supplies a horizontal deflection circuit of a television receiver.
This horizontal deflection circuit which comprises in cascade a horizontal oscillator, a driver stage and an output stage, forms an integral part of the circuit controlling said first transistor and determines the repetition period of the switching, because it is started under an initial voltage slightly less than the unregulated input voltage of the device.
The switching transistor is being turned off in synchronism with the turning off of the trace switch transistor by using flyback pulses of negative polarity to bias the base thereof.

1. A power supply device with switching regulation and boosting of its DC output voltage, combined with a horizontal deflection circuit of a television receiver, supplied thereby and which comprises in cascade a horizontal oscillator, a driver stage and an output stage including a trace switch transistor and a line transformer, this device comprising an inductance and the collector-emitter path of a switching transistor connected in series between the poles of a DC input voltage source, a rectifying diode connected by its anode to the junction between the inductance and the collector of said switching transistor and by its cathode to one of the terminals of a filtering and storage capacitor whose other terminal is connected to the emitter of said transistor, so as to apply across its terminals an initial DC voltage slightly lower than said input voltage, when said switching transistor is turned off, and a regulated DC output voltage with a level higher than said input voltage, when said transistor is recurrently, alternately turned on and off, the level of said output voltage depending on the duty cycle of said switching transistor states, and a control circuit feeding the base of said switching transistor and including a regulator stage comparing an adjustable fraction of said output voltage to a fixed reference voltage and supplying a regulating current or voltage proportional to the difference between said compared voltages, a pulse-width modulator triggered by means of a recurrent signal and supplying a rectangular signal whose duty cycle varies as a function of said regulating current or voltage, another driver stage receiving the rectangular signal and controlling said switching transistor, the regulation and boosting of said output voltage being controlled by the initially independent starting up of the entire horizontal deflection circuit when supplied by said initial voltage from said power supply device as soon as a DC input voltage is applied thereto and which then delivers recurrent trigger pulses to said pulse-width modulator, one of the supply inputs of said other driver stage receiving directly a first voltage waveform whose positive alternations comprise constant-voltage plateau and whose negative alternations comprise negative-going horizontal flyback pulses provided by a first secondary winding of said line transformer, so as to control the turning off of said switching transistor substantially simultaneously with that of the trace switch transistor.

2. A power supply device as claimed in claim 1, wherein said other driver circuit comprises a third transistor whose emitter is connected to the base of said switching transistor and which is of the same type as the latter, whose collector is connected, through said supply input, to said first secondary winding of said line transformer to receive therefrom said first waveform and whose base is coupled to the output of said pulse-width modulator.

3. A power supply device as claimed in claim 2, wherein the collector of said third transistor is connected, through a resistor to the supply input and its emitter is connected, furthermore, to that of the switching transistor through another resistor so that the negative-going flyback pulses, applied to the collector of said third transistor, control the symmetric (reverse) saturation thereof so as to reversely bias the base-emitter junction of said switching transistor.

4. A power supply device as claimed in claim 2, wherein the collector of said third transistor is connected to said power supply input through a fourth diode conducting in the normal direction of its collector-emitter path, and wherein its emitter is further connected, on the one hand, through a resistor, to the emitter of the switching transistor and, on the other hand, through another resistor and a fifth diode conducting in the reverse direction to that of the base-emitter junction of the switching transistor, so as to transmit to the base thereof negative-going flyback pulses through a voltage divider formed by said two resistors in series.

5. A power supply device as claimed in claim 1, wherein said other driver circuit comprises a third transistor whose emitter is connected to the base of said switching transistor, whose collector is connected to that of this latter so as to form a so-called Darlington circuit and whose base coupled, moreover, to said pulse-width modulator is further connected, through a resistor and a diode in series, to said first secondary winding of said line transformer so as to control the simultaneous turn off of both transistors of said Darlington circuit by simultaneously reversely biasing their respective base-emitter junctions, connected in series, by means of negative-going flyback pulses.

6. A power supply device as claimed in any one of the preceding claims, wherein said pulse-width modulator, supplied at its input with a voltage waveform whose positive alternations comprise positive-going flyback pulses and whose negative alternations comprise constant negative-voltage plateaux, comprises a passive circuit which forms a simple integrator during positive alternations because one of its resistors is shunted by a diode and which is a cascaded double integrator during negative alternations of this waveform so as to deliver during the trace periods of the scan a linearly decreasing negative current which, added to the positive regulating current, supplies the base of a fourth comparator transistor, so that the turning off of this latter through equality of the negative and positive currents supplied to this base controls the beginnings of the saturation of said switching transistor in such a manner that the duration of this saturation varies inversely with variation of said output voltage.

7. A power supply device as claimed in claim 6, wherein said comparator transistor is biased, furthermore, at its base by means of a resistor which connects it to the positive pole of said input voltage source, so that it remains saturated in the absence of flyback pulses supplied by said horizontal deflection circuit so as to maintain the switching transistor in a cut off state.

8. A power supply device as claimed in any one of the preceding claims, wherein said control circuit, except for the regulator stage which is supplied by said output voltage, is supplied by said input voltage.

9. A power supply device as claimed in any one of the preceding claims 1 to 6, wherein said DC supply voltage of said control circuit, with the exception of one of the inputs of said regulator stage receiving said output voltage, is supplied by a secondary winding of said line transformer, through a rectifier circuit including a diode and a filtering capacitor.

Description:

BACKGROUND OF THE INVENTION

The present invention relates to a switching voltage regulator power supply device combined with the horizontal deflection circuit of a television receiver which it supplies with DC voltage. It relates, more particularly, to DC voltage supply devices of the type which boost or increase the voltage supplied at the output of the device in relation to the level of a DC voltage applied to its input and which regulate this level by recurrent switching of this input voltage, this switching being synchronous with the (horizontal) line frequency of the television receiver supplied by this device.
Switched step-up or boost voltage regulator devices of this type are known, particularly from the publications U.S. Pat. Nos. 3,571,697 (or 3,736,496) and they are related to switched mode power supply devices or DC-DC converters of the so-called unisolated flyback type, in which the collector-emitter path of a bipolar switching transistor is connected in series with a commutating inductance between the terminals of a DC source supplying an input voltage and a rectifying diode is connected between the junction of the inductance with the transistor and one of the plates of a filtering or storage capacitor (in parallel with the load), so that the current stored in the inductance during the conducting period of the transistor is used for charging the capacitor (and supplying the load) through the diode during its consecutive cut-off period. The use of a switched-mode power supply device of this type in television receivers for supplying, particularly, the horizontal deflection circuit thereof has been described, for example, in two articles by VAN SCHAIK entitled respectively "AN INTRODUCTION TO SWITCHED-MODE POWER SUPPLIES IN TV RECEIVERS" and "CONTROL CIRCUITS FOR SMPS IN TV RECEIVERS," appearing respectively on pages 93 to 108 of No. 3, Vol. 34, of September 1976 and on pages 162 to 180 of No. 4 of this same volume, of December 1976, in the English language Dutch review "ELECTRONIC APPLICATIONS BULLETIN" of PHILIPS', or on pages 181 to 195 of No. 135 of July 1977 and on pages 210 to 226 of No. 136 of October 1977 of the British review "MULLARD TECHNICAL COMMUNICATIONS." Since none of the switched-mode power supply devices described in these articles, isolated or not from the mains, whether they use a forward or a flyback converter, supplies at its output a DC voltage for supplying the horizontal deflection circuit before the switching transistor has been turned on (saturated or conducting) one or more times, the control circuit of this transistor must comprise an independent relaxation oscillator and must be supplied by the same DC input voltage (rectified and smoothed voltage of the AC mains) as the switching circuit comprising the inductance and the transistor in series. Synchronization of the switching with the horizontal deflection can only occur subsequently, when the horizontal oscillator and/or the horizontal deflection circuit as a whole have begun to operate, as soon as the supply voltage supplied thereto by the device which operates independently on starting up, has become sufficient. This synchronization of the switching with the horizontal deflection, advantageous for reducing or eliminating the interferences visible on the screen which are caused by high-frequency energy radiation due to abrupt transitions of power switching, particularly when the switching transistor is being cutt off, is generally carried out by means of a signal comprising flyback or retrace pulses, taken at the terminals of an auxiliary secondary winding of the line tranformer whose primary winding is generally connected between the output of the switched-mode power supply device and one of the terminals of the trace switch which is provided in the output stage. It is also possible to use for this purpose the signal provided by the horizontal oscillator (see, for example, the publication FR-A-2 040 217).

In a switched-mode supply for a television receiver described in the publication FR-A-2 261 670, the circuit for controlling the switching transistor of a forward-type converter, supplied with the rectified and smoothed voltage of the mains, comprises a bistable trigger circuit of flip-flop one of whose outputs is coupled back to one of its trigger inputs through a regulating circuit comprising a sawtooth voltage generator and a voltage comparator providing transitions which control the setting of the flip-flop, when the sawtooth voltage reaches the level of a voltage proportional to the amplitude of the flyback pulse. The other one of the two complementary outputs of this flip-flop is coupled back to its other trigger input through a so-called starting loop comprising an ascending voltage wave-form which approaches asymptotically a predetermined voltage level smaller than a predetermined fraction of the nominal level which the amplitude of the flyback pulse must reach in normal operation, and a voltage comparator providing transitions which control the recurrent resetting of the flip-flop to its initial state until the flyback pulse has reached or exceeded a threshold amplitude slightly below its nominal amplitude. When this threshold amplitude has been exceeded, resetting of the flip-flop is controlled by the flyback pulses themselves, negative-going in the present case, which supplant the starting pulses. Such an arrangement is equivalent to an astable multivibrator during the starting period, which later becomes a monostable one and triggered by the flyback pulses and whose quasi-stable state has a variable duration, depending on the amplitude of these pulses so as to obtain regulation thereof by the duty cycle. The pulse which controls the closing of the switch (saturation of the switching transistor) begins here with the leading edge of the flyback pulse and its duration or length is modulated as a function of the current drawn by the load and of the variation of the rectified and smoothed voltage, so that its end controlling the opening of the supply switch (cutting off the transistor) occurs during the trace portion of the horizontal deflection. Thus it can be seen that this switched-mode supply, like most of the known ones, effects regulation of its output voltage by varying the duty cycle as a reverse function of the level thereof.
Since the high-frequency radiation is precisely at its most intense during abrupt transitions of current in the switching inductance and of the voltage accross its terminals, the appearance of one or more vertical lines (light or dark according to the sense of the modulation of the carrier wave by the video signal) may be observed, contrasting with the normal contents of the picture, whose location on the screen depends on the duration of the pulse controlling the switching transistor. The effect of this radiation becomes particularly troublesome when the input signal of the radio-frequency stages or tuner is small, particularly when the selected channel is situated in the lower part of the VHF band, for the automatic gain-control device of the receiver acts on the gain of the high-frequency and/or intermediate-frequency input stages, so that the sensitivity (amplification) of the receiver is then maximum and this also as concerns the spurious radiated signals.
SUMMARY OF THE INVENTION
The present invention, on the one hand, avoids or at least appreciably reduces the interferences visible on the screen by controlling the cutting off of the switching transistor in synchronism with the leading edge or the flyback pulse and, on the other hand, the starting of the horizontal deflection circuit by means of a simple circuit without any special oscillator, and provides efficient protection of the switching transistor which remains cut off when the horizontal deflection circuit is not operating. This is made possible by using a step-up switching regulator supply device of the type described in the publication U.S. Pat. No. 3,571,697 and whose control circuit includes, in accordance with the invention, the horizontal deflection circuit, which it supplies.
The object of the present invention is a power supply device with boosting and regulation of its output voltage by switching, combined with a horizontal sweep circuit of a television receiver, which it supplies and which comprises a horizontal oscillator, a driver stage and an output stage including a line transformer, this device comprising an inductance and the collector-emitter path of a switching transistor connected in series between the poles of a DC input voltage source, a rectifiying diode connected by its anode to the junction between the inductance and the collector of the transistor and by its cathode to one of the terminals of a filtering capacitor whose other terminal is connected to the emitter of the transistor so as to supply between its terminals an initial output voltage, slightly lower than the input voltage, when the transistor is cut off permanently, and a regulated DC output voltage with a level higher than the input voltage, when the transistor is recurrently alternately turned on and off, the level of this output voltage depending on the duty cycle of the respective states of this transistor, and a control circuit for driving the base of the transistor and including a regulator stage comparing an adjustable fraction of the output voltage to a fixed reference voltage and supplying a regulating current or voltage proportional to the difference between these compared voltages, to a pulse-width modulator triggered by means a recurrent signal and supplying a rectangular signal whose duty cycle varies as a function of this regulating current or voltage, and another driver stage receiving the rectangular signal and controlling the switching transistor.

In accordance with the invention, the horizontal deflection forming an integral part of the circuit controlling the switching transistor, determines therefor, from the start, the repetition period of the rectangular signal controlling it, and one of the supply inputs of the other driver stage receives directly a first voltage waveform whose positive alternations, comprise DC voltage plateaux and whose negative alternations comprise negative-going flyback pulses supplied by a first secondary winding of the line transformer, so as to control the cut-off the switching transistor substantially simultaneously with that of the trace switch transistor.
DESCRIPTION OF THE DRAWINGS

The invention will be better understood and other of its objects, characteristics, features and advantages will become clear from the following description and the accompanying drawings which refer thereto, given solely by way of example, in which:
FIG. 1 is partly a block diagram and partly a schematic diagram of a power supply device combined with the horizontal deflection circuit in accordance with the invention;
FIG. 2 shows waveforms of two voltages and of a current at different points of the circuit of FIG. 1;
FIG. 3 is a block diagram of the circuit for controlling the switching transistor;
FIGS. 4 and 5 are schematic diagrams of two different embodiments of the driver circuit 20 forming the output stage of the control circuit of FIG. 3;
FIG. 6 is the block diagram of one embodiment of the pulse-width modulator 10 of the circuit of FIG. 3;
FIG. 7 shows three voltage waveforms at different points of the circuit of FIG. 6;
FIG. 8 is a schematic diagram of one embodiment of the pulse-width modulator 10 of the circuit of FIG. 3, using discrete components;
FIG. 9 shows a current waveform and two voltage waveforms at different points of the circuit of FIG. 8;
FIG. 10 is a schematic diagram of a conventional embodiment of a regulator stage 30 adapted to supply the modulation input of the modulator of FIG. 8; and
FIGS. 11 and 12 are partial respective schematic diagrams of two embodiments of a power supply device in accordance with the invention.
DESCRIPTION OF THE PREFERRED EMBODIMENTS
FIG. 1 shows the schematic diagram of the power stages of the power supply device and of the horizontal deflection circuit of the television receiver, which it supplies and in block diagram form the respective circuits which control them.
The DC input voltage VE which is not regulated is supplied by a rectifier bridge R with four diodes, supplied at its input by the secondary winding of an insulating step-down transformer TS, whose primary winding is supplied by the AC mains. The output terminals of rectifier bridge R are connected respectively to the terminals of a first filtering capacitor C1 across which this input voltage VE is taken.
The positive pole P of this source of the input voltage VE is connected to one of the terminals of an energy-storage inductance L, whereas its negative pole N is connected to ground G of the receiver, which is isolated from the mains. The other terminal of inductance L is connected, on the one hand, to the collector of a first NPN bipolar switching transistor T1, whose emitter is connected to ground G and, on the other hand, to the anode of a first diode D1 whose cathode is connected to the positive terminal of a second filtering and storage capacitor C2. With the negative terminal of this second capacitor C2 connected to ground G, the output voltage VS which supplies the load is taken between its terminals.
Such a supply device BS provides both step-up or boost and regulation of its output voltage level, because the first switching transistor T1 and the first diode D1 thereof are connected so as to conduct respectively currents flowing through inductance L in the same direction, it supplies at its output formed by the terminals of the second capacitor C2, an initial DC voltage VSI as soon as the primary winding of the insulating transformer TS is connected to the mains. This initial voltage VSI which is equal to the input voltage VE less the forward voltage drop VD1 across the first diode D1, is then supplied to the load until the control circuit SC is started up, whose output 6 is connected to the base of the first transistor T1 so as to cause it to be alternately turned on and off.
When the first transistor T1 is turned on by positively biasing its base-emitter junction, its collector-emitter path connects the junction of the inductance L with the anode of the first diode D1 to ground G. Diode D1 being then reversely biased, it ceases to conduct and the inductance L connected by the first transistor T1 between the positive P and negative N poles of the source supplying the unregulated DC input voltage VE, then conducts a linearly increasing current IL so as to store the energy which increases with the square of the conduction duration of the first transistor T1, until this latter is cut off. At the instant when the first transistor T1 is cut off after the control circuit SC has brought its base-emitter voltage to zero or below, the voltage at the terminals of inductance L is reversed so that, at its junction with the collector of transistor T1 and the anode of diode D1, there appears a voltage VM greater than the input voltage VE, which results in the forward biasing of diode D1. Consequently, from the instant when transistor T1 is cut off, diode D1 conducts a linearly decreasing current until the energy stored in the form of a current IL in the inductance L, which charges the second capacitor C2 to an output voltage VS greater than the input voltage VE, disappears. The regulation of the level of the output voltage VS is here effected in a conventional way, by varying the duty cycle, i.e. the radio (quotient) between the duration of the conducting period of transistor T1 and the sum of the respective durations of two of its successive conducting and cut off periods, as a function of the desired output voltage VS (determined by comparison to a stable reference voltage).

According to the invention, a supply device BS of the above-described type is combined with the horizontal deflection circuit SH of a television receiver, which it supplies, so that this latter forms an integral part of its control circuit SC and for determining the repetition period of its operation and so that the above-mentioned regulation by varying the duty cycle maintains a stable peak-to-peak amplitude of the sawtooth scanning current and/or the very high voltage for biasing the electrodes (anode, focusing electrode and accelerating grid) of the cathode-ray tube, which are obtained by rectifying the horizontal flyback pulses supplied by a step-up secondary winding (not shown) of the line transformer TL.
The horizontal deflection circuit SH which comprises in cascade the horizontal oscillator OH whose known phase control circuit with respect to the horizontal sync signal separated from the composite video signal has not been shown here, the driver stage HD controlled by the horizontal oscillator OH and controlling the output stage OS of the horizontal deflection, is as a whole supplied by the above-described regulated power supply device BS. In fact, the positive supply input AL of the horizontal deflection circuit SH is connected by means of a fuse FS to the junction of the cathode of the first diode D1 with the positive terminal of the second capacitor C2, which forms the positive output terminal SP of the regulated power supply device BS. This supply input AL is connected directly to that of the driver circuit HD and, preferably, through a conventional Zener diode or series ballast transistor voltage regulator VR, to that of the horizontal oscillator OH, which are moreover connected to the isolated ground G.
The supply input AL of the horizontal deflection circuit SH is furthermore connected to one of the primary winding terminals B1 of the line transformer TL, whose other terminal AB is connected in parallel to the collector of another switching transistor TH, of NPN type, called trace switch transistor, to the cathode of a second so-called shunt recovery diode DR, to one of the terminals of another capacitor CR, called line-retrace capacitor, and to one of the plates of an additional capacitor CS, called trace capacitor, which supplies the horizontal deflection coils LH one terminal of which is connected to its other terminal during the trace periods of the scanning. The emitter of the scanning transistor TH, the anode of the "shunt" recovery diode DR, the other terminal of the retrace capacitor CR and the other terminal of the horizontal deflection coils LH are all connected to ground G. This assembly of components thus connected forms the output stage OS whose operation is well-known and does not form part of the invention.

As was mentioned above, as soon as the primary winding of the step-down isolating transformer TS is connected to the mains, rectifier R supplies the first filtering capacitor C1 so as to provide between its terminals P and N a unregulated low DC voltage VE. With the first transistor T1 then turned off, this input voltage is applied through the inductance L and the first diode D1 to the second capacitor C2 so as to obtain between the terminal SP and ground G an initial output voltage VSI substantially equal to VE-VD1, which is approximately equal to 60 percent of the regulated output voltage VS. This initial output voltage VSI (equal to about 0.6 VS) is sufficient to cause the generation of autonomous oscillations by the horizontal oscillator OH. This latter supplies at its output, connected to the input of driver circuit HD, pulses at an independent frequency close to the line frequency. In response to these pulses, driver circuit HD, also supplied by device BS, provides at the base of the trace switch transistor TH pulses controlling its periodical cut off at this independent frequency and its consecutive turning on after a period greater than the duration of the flyback period, so that the recovery diode DR may take the current from the deflector LH during substantially the first half of the trace portion of the scan. During flyback or retrace, with both transistor TH and diode DR cut off, the energy stored in the form of currents respectively in the inductances of deflector LH and of the primary winding B1 of the line transformer TL which are then, from the AC current point of view, connected in parallel, flow in an oscillating manner through the retrace capacitor CR which forms therewith a parallel resonant circuit whose resonance period determines the duration of the flyback period.
There then appears periodically between point AB and ground G a voltage pulse VTH having substantially a sinusoidal half-wave form, which is shown in Diagram A of FIG. 2. The average value of this voltage VTH being then equal to VSI, at start-up, and to VS, during established operation. The line transformer TL comprises, in addition to a very-high-voltage winding and other windings for supplying rectifying circuits, not shown, two secondary windings B2, B3 respectively supplying across their terminals, voltage waveforms comprising flyback pulses with zero average values and with respectively negative and positive polarities.

This means that the first secondary winding B2 supplies a voltage waveform -VTL which, between two successive flyback pulses, comprises a positive plateau whose level is equal to the average value of these pulses and which is used, in accordance with the invention, to control the turn off of the first transistor T1 so that the interferences which would otherwise be visible only occur during the line-blanking periods comprising the line-retrace periods. The second secondary winding B3 then supplies a voltage waveform +VTL which is the reverse of or complementary to the preceding one -VTL.
One of the terminals of each of these secondary windings B2, B3 is connected to ground G, whereas their other terminals are respectively connected to two inputs 2 and 1 of the control circuit SC. A third input 3 of this latter is connected to the SP output of the supply device BS and a fourth input 4 is connected to the positive pole P of the input voltage source VE. A fifth terminal 5 of the control circuit SC is connected to ground G (or negative pole N) and its output 6 is connected to the base of the first transistor T1. This control circuit SC causes, following the start up of the horizontal deflection circuit SH, a first saturation of the first transistor T1 at a time determined by a pulse-width modulator operating by conventional comparison of a sawtooth voltage waveform the elaboration of which is controlled by a first flyback pulse, with a regulating voltage, depending on the output voltage VS. During this saturation period of transistor T1 which extends as far as the leading edge of the next flyback pulse, energy is stored in inductance L.
From the instant when transistor T1 is turned off, diode D1 transfers this stored energy to the second capacitor C2, at the terminals of which it causes an increase of the voltage VS with respect to its initial value VSI, until the current in diode D1 is canceled out, when it becomes reverse biased.
The collector-emitter voltage waveforms VTH of the trace switch transistor TH and VCE of the switching transistor T1 in established operation have been shown respectively by the diagrams A and B of FIG. 2. Diagram C of FIG. 2 shows the corresponding waveform of the current IL flowing through the inductance L.
When the base of the first transistor T1 receives from the output 6 of the control circuit SC a rectangular signal which turns it on at time instant t1, its collector-emitter voltage VCE (Diagram B) becomes close to zero (V _CEsat ) and a linearly increasing current IL (Diagram C) flows through inductance L from time t1 until time t2 when transistor T1 is again turned off, which is controlled by the leading edge of the flyback pulse VTH (Diagram A). With the collector current of transistor T1 canceled at the end of the storage time of the excess minority carriers in the base, the voltage across the terminals of the inductance L inverses its polarity so as to be added to the input voltage VE, so that the collector-emitter voltage VCE (Diagram B) then reaches a level VM greater than VS (as well as VE), so as to apply forward bias to the first diode D1, which then conducts the current IL through the inductance L. This current IL, from time instant t2 when it reaches its maximum value IM, becomes linearly decreasing and it flows through the first diode D1 in the passing direction in order to recharge the second capacitor C2 and supply, in particular, the horizontal deflection circuit SH.
When the current IL passing through the first diode D1 is canceled out at time t3, the collector-emitter voltage VCE of the first transistor T1 becomes equal to the unregulated input voltage VE until the next turn on of the transistor T1, and the first diode D1 remains reversely biased until the time when this latter is cut off again.
From the above it can be easily seen that the principal advantage of this combined device resides in the fact that a single oscillator OH belonging to the horizontal deflection circuit SH is sufficient for controlling the two power switching transistors TH and T1.
Furthermore, a possible overload in the circuitry of the television receiver, such for example as a short-circuit of the trace switch transistor TH, results in overloading the diode D and the inductance L. The first transistor T1 which is consequently cut off is not subjected to this overload and is therefore protected. In order to protect the rest of the television receiver as well as inductance L and the first diode D1, a fuse FS may be connected in series in the supply line from the second capacitor C2. This fuse FS may also be inserted between pole P and inductance L.

It is moreover known that it is difficult to construct switched supplies for obtaining correct operation when it is not fully charged (for supplying, for example, a ready-state remote-control receiver). In the present case, the problem does not come up since, when the supply is in operation, there is always a minimum load formed by the horizontal deflection circuit. When this circuit is not operating, the supply circuit BS does not operate either, but it supplies an output voltage VSI of a value less than the nominal voltage VS which cannot cause damage and which may, for example, supply a ready-state receiver for television receivers having a remote control.
Finally, the control circuit SC allows transistor T1 to be cut off at the beginning of each flyback period, when the blanking circuit has extinguished the spot (s) on the cathode-ray tube. Thus, the spurious signals radiated into the receiver input circuits will cause no visible effect on the screen of the cathode-ray tube.
FIG. 3 shows in block diagram form the control circuit SC of FIG. 1.
This control circuit SC comprises a pulse-width modulator stage 10 a first input 11 of which, connected to input 1, receives flyback pulses of positive polarity +VTL from the second secondary winding B3 of the line transformer TL (see FIG. 1 and a second input 12 of which receives a so-called regulating voltage or current whose level is proportional to the difference between the actual output voltage VS and a constant reference value, delivered by the output 32 of a regulating circuit or stage 30 whose input 31 is connected through input 3 to the positive output pole SP of the supply device BS supplying the regulated voltage VS. The variation of the regulating current or voltage causes the variation of the time instant when the instantaneous amplitude of a sawtooth voltage waveform, either with substantially constant slope and amplitude, reaches the level of this regulating voltage, or with a slope variable depending of the regulating current (which is added to the current for linearly charging a capacitor), reaches the predetermined level of a fixed reference (threshold) voltage, with respect to the beginning or the end of the sawtooth waveform. Thus a two-level rectangular signal with constant periodicity is generated, whose duty cycle varies as a function of the regulating current or voltage. If it is arranged, which is possible, for a reduction of the output voltage VS with respect to its nominal value defined by the reference voltage, to cause an increase in the duty cycle and for an increase in VS to have the opposite effect, regulation of this output voltage VS is provided, which tends to be stabilized to this nominal value.
The output 14 of modulator 10 supplies a first input 21 of the driver stage 20 of the first switching transistor T1, a second input 22 of which receives the flyback pulses of negative polarity -VTL, coming from the first secondary winding B2 of the line transformer TL.
FIGS. 4 and 5 illustrate two different embodiments of the driver stage 20 of FIG. 3, providing efficient turn off of the first transistor T1.
In FIG. 4, the driver stage 20A comprises a third supply input 23 which connected to the positive pole (P) of the source of the (unregulated) input voltage VE and to one of the terminals of a first resistor R1 (1.8 kiloohms) whose other terminal is connected in parallel to the anodes of two diodes D2 and D3 (of type 1N4148). The second of these diodes D3 has its cathode connected to the base of a third NPN transistor T2 and to one of the terminals of a second resistor R2 (220 ohms). The emitter of the third transistor T2 is connected to the other terminal of the second resistor R2 and to the output 24 of stage 20A, which is connected through the output 6 of the control circuit SC to the base of the first transistor T1. The collector of the second transistor T2 is connected through a third resistor R3 (10 ohms) to the second input 22 of stage 20A receiving the signal -VTL which comprises the negative-going flyback pulses and, between them, plateaux of a constant positive level (zero average value). The base of the first transistor T1 is coupled to its emitter and to ground G, through a fourth resistor R4 (100 ohms). The third transistor T2 is thus mounted as a common collector (emitter-follower) stage.

When the output 14 of modulator 10 (FIG. 3) which is connected to the input 21 of stage 20A supplies a low state (level), i.e. a voltage close to zero, the thus positively biased diode D2 becomes conducting so that its anode will be at a voltage of a few tenths of a volt (0.7+V _CEsat ) which is less than the voltage required for making the three series PN junctions orientated in the same direction conductive, the first of which is formed by the third diode D3, the second is the base-emitter junction of a third transistor T2 and the third that of the first transistor T1, which will thus remain turned off. When, on the other hand, output 14 supplies a high state or forms an open circuit (the output stage of modulator 10 being formed by an open-collector transistor), diode D2 is cut off by its reverse bias and the voltage VE applied to the input 23 causes a current to flow through the first resistor R1, the diode D3 and the respective base-emitter junctions of transistors T2 and T1 connected in series. Under these circumstances and if, at the same time, the voltage waveform -VTL applied to the collector of transistor T3 presents its constant positive level portion, coinciding with the trace periods of the horizontal scan, transistors T2 and T1 become simultaneously saturated with the effect previously described insofar as the supply device BS of FIG. 1 is concerned. On the other hand, when the voltage waveform -VTL applied to the collector of the third transistor T2 becomes negative, during flyback periods, the current then flows between terminals 23 and 22 of driver stage 20 A, through resistor R1, diode D3, the base-collector junction of the third transistor T2 and resistor R3. The third transistor T2 then operates along its symmetrical saturation characteristics, i.e. it is inverted so that its collector becomes emitter and vice versa. It then conducts a current in the reverse direction between ground and the input 22 (negative) through the resistor R4 across the terminals of which it causes, after removal of the excess minority carriers from the base of the first transistor T1 through the third transistor T2, a voltage drop biasing said base negatively with respect to the emitter. This negative voltage applied to the base of reversely saturated transistor T3 allows a considerable reduction in the storage time and a rapid turnoff of the first transistor T1. Since the sawtooth generator of the pulse-width modulator 10 described above is controlled by positive-going flyback pulses, the rectangular signal applied by its output 14 (FIG. 14) to input 21 of stage 20A undergoes, during the flyback period following the turn off of the first transistor T1, a transition from its high state to its low state which causes diode D2 to conduct and, consequently, the third transistor T2 (reversed) to be cut off before the waveform -VTL becomes positive again and rebiases this transistor T2 the right way round.
FIG. 5 shows the schematic diagram of another embodiment of the driver circuit 20 of FIG. 3, designated by 20B, which has only been modified with respect to circuit 20A of FIG. 4 insofar as the collector circuit of the third transistor T2 and the base circuit of the first transistor T1 are concerned.
T

his modification is more particularly intented for the case where the negative peak amplitude of the voltage waveform -VTL applied to the base of the first transistor T1 through resistor R3 and the emitter-collector path of the reversely saturated third transistor T2, exceeds the reverse (Zener) avalanche-effect breakdown voltage of one of the base-emitter or base-collector junctions of the first transistor T1. This may occur when the first secondary winding B2 of the line transformer TL is also used for other functions in the television receiver.
To prevent the third transistor T2 from being reversely saturated (symmetrically), the circuit 20B comprises a fourth diode D4 inserted between the input 22 receiving the voltage waveform -VTL and the collector thereof, in series with the resistor R3 and connected to conduct in the same direction as its collector-emitter path. The input 22 is more over connected to the cathode of a fifth diode D5 (1N4148) whose anode is connected through a circuit formed by a fifth resistor R5 (330 ohms) and a third capacitor C3 (1nF) connected in parallel, to the base of the first transistor T1.
Diode D5 isolates the base of transistor T1 from the input 22, when the waveform -VTL is positive, and connects them together through a resistive voltage divider formed by resistors R5 and R4 in series, when it becomes negative. Capacitor C3 accelerates the turn-off by favoring the transmission to the base of T1 of abrupt transitions of the negative flybacd pulses.
FIG. 6 is a diagram, partly in block form, of a possible embodiment of the pulse-width modulator 10 of the control circuit SC of FIG. 3. Diagrams D, E and F of FIG. 7 show the voltage waveforms applied respectively to the input 11 (+VTL) and supplied by the output SI (VI) of the sawtooth generator GD and by the output 14 (VP) of circuit 10A.
Modulator 10A of FIG. 5 comprises a sawtooth generator GD formed by a conventional integrator circuit comprising a first amplifier A1 (integrated operational amplifier, for example), an integrating resistor R1 inserted in series between the input 11 receiving the voltage waveform +VTL illustrated by Diagram D of FIG. 7 and supplied by the second secondary winding B3 of the line transformer TL, and the input (inverting) of amplifier A1, as well as an interating capacitor CI connected between this input and the output SI of amplifier A1 (capacitive feedback). In response to this waveform +VTL, the output of amplifier A1 forming the output SI of sawtooth generator GD, supplies a voltage waveform VI illustrated by the diagram E of FIG. 7 which comprises, during the period between time instants t0 and t2 corresponding to the trace period TA of the scan, a voltage decreasing linearly between a maximum value (positive) and a minimum value (negative), and during the flyback intervals preceding time instant t0 and succeding to time instant t2, an increasing voltage of substantially semi-cosinusoidal shape.
Voltage VI is applied to one of the inputs (-) of an analog voltage comparator which may be formed by means of a second differential-type amplifier A2 (integrated operational amplifier), whose other input (+) connected to the input 12 of modulator 10A, receives the regulating voltage VR supplied by the regulator stage (30 of FIG. 3). This regulating voltage VR, which is obtained by comparing the output voltage VS of the supply device BS of the circuit of FIG. 1 with a reference voltage (VZ supplied by a Zener diode, for example), is a DC voltage undergoing slow variations, shown in Diagram E of FIG. 7 by a dash-dot line.
When the waveform VI applied to the inverting input (-) of comparator A2 is greater than the regulating voltage VR, which is the case during the period between time instants t0 and t1, its output connected to the output 14 of modulator 10A provides a low state. When, on the other hand, it (VI) reaches or becomes less than VR, which occurs from the time instant t1, the output 14 of modulator 10A provides a high state (which causes saturation of the first transistor T1). This high state continues until time instant t4 subsequent to the time instant t2 of the beginning of the following flyback pulse whose leading edge controls the turn-off of the first transistor T1, when the waveform VI becomes greater than the regulating voltage VR. Thus there is obtained at the output 14 of modulator 10A a rectangular signal VP shown in Diagram F of FIG. 7, formed successively of a low-level (zero or negative) beginning during the first half of the flyback period TR and ending at time instant t1, and a high level going from time instant t1 to time instant t4. Time instant t1 of the positive transition of signal VP, which determines the beginning of conduction of the first transistor T1 is then situated during the trace period of the scan TA and its position with respect to the beginning t0 or to the end t2 thereof varies as a function of the regulating voltage VR. When the regulating voltage VR is negative (as on the Diagram E of FIG. 7), a predetermined fraction of the output voltage VS is greater than the reference voltage, the duration of the high level state (t2-t1) is less than half of the trace period of the scan T1. In the opposite case, this duration (t2-t1) is greater than TA/2. The modification of this duration (t2-t1) and thus of the duty cycle is carried out in the reverse direction of the variation of the output voltage VS so as to stabilize it at a previously adjusted level, with respect to this reference voltage. The waveform -VTL may also be applied to the input 11 of modulator 10A. In this case, the input of comparator A2 must also be inverted.

To obtain suitable operating limits, while taking into consideration particularly the value of inductance L, the duty cycle or the durations (t2-t1) must vary between 0, the case where the input voltage VE is equal to the nominal output voltage VS, and about two-thirds, the case where the maximum power is supplied for a minimum voltage at the input.
The ratio between the residual alternating voltage (hum) at the output and the alternating voltage at the input must also allow an image to be obtained which is not perturbed for the eye. A value less than or equal to a hundredth for this ratio gives satisfactory results.
FIG. 8 shows the simplified diagram of a practical embodiment (by means of discrete components) of the pulse-width modulator 10 of FIG. 3. Different waveforms of a current I1 and input +VTL and output VP voltages are respectively illustrated by the Diagrams H, J and K of FIG. 9.
The input 11 of modulator 10B of FIG. 3 receives the voltage waveform +VTL which may be suppled either directly by the second secondary winding B3 of line transformer TL, or through a coupling capacitor whose one terminal is connected to the collector of the trace switch transistor TH (see FIG. 1). This input 11 supplies a passive shaping circuit, supplying negative-going (decreasing) sawtooth waveforms during the trace periods of scan T1. This passive circuit comprises a fourth coupling capacitor C4 (0.1μ) one terminal of which is connected to the input 11 and the other of which is connected to one of the terminals of a sixth resistor R6 (10 Kohms). The other terminal of this resistor R6 is connected to one of the terminals of a seventh resistor R7 (5.6 Kohms), to one of the terminals of a fifth capacitor C5 (5.6 nF) and to the anode of a sixth diode D6. The other terminal of capacitor C5 is connected to ground G. The cathode of the sixth diode D6 and the other terminal of resistor R7 are both connected to one of the terminals of an eighth resistor R8 (33 kohms), to that of a ninth resistor R9 (470 ohms), to that of a sixth capacitor C6 (4.7 nF) and to the regulation input 12 of modulator 10B, which is connected to the output 32 of the regulator stage 30 (see FIG. 3). The other terminal of capacitor C6 is connected to ground. The other terminal of resistor R8 is connected to the supply input 13 of modulator 10B receiving the input voltage VE. The other terminal of the ninth resistor R9 is connected to the base of a fourth NPN transistor T3, which forms the voltage comparator stage, whose emitter is connected to ground and whose collector (open), which forms the output 14 of modulator 10 B, is connected to the input 21 of the driver stage 20A (of FIG. 4) or 20B (of FIG. 5), formed by the cathode of the second diode D2. The value of capacitor C6 has been chosen so as to limit the maximum negative voltage applied to the base-emitter junction of transistor T3 to a value less than its reverse avalanche breakdown voltage. When the input voltage waveform +VTL is positive, as during the major portion of the flyback periods TR, diode D6 short-circuits resistor R7 and we have then a simple passive RC integrator formed by resistor R6 in series and two capacitors C5 and C6 in parallel, whose output is connected to the base of transistor T3 through resistor R9. Transistor T3 becomes conducting when its base current IB formed by the sum of currents I1 and I2 becomes positive. The current I1 shown by an arrow in FIG. 8 and on the Diagram H of FIG. 9, results from the application of the +VTL waveform of Diagram J to the above-mentionned simple integrator, during its positive alternation, and to the cascaded double integrator R6, C5, R7, C6 during its negative plateau going from t0 to t2. During this negative voltage plateau of the +VTL signal, the current I1 becomes negative and linearly decreasing. When the instantaneous negative amplitude of current I1 becomes equal to the positive current I2 shown by another arrow in FIG. 8 and by means of a reversed constant level (-I2) shown by a broken line in diagram H of FIG. 7, which occurs at time t1, the base current of transistor T3 is cancelled out and this latter is cut off. Since the current I2 is due for a large part to the regulating current IR supplied by the output of the regulator stage (30 in FIG. 3) and proportional to the error voltage, the duration of the cut-off state (t4-t1) of transistor T3 and, consequently, that (t2-t1) of the saturated state of the first transistor T1 (as well as the duty cycle) will vary reversely to the variation of this current IR. The current IE shown by an arrow in FIG. 8, which flows through the high-value resistor R8 from the input voltage source VE and which is one of the components with IR of current I2, forms a small current for maintaining transistor T3 saturated in the absence of flyback pulses and thus of horizontal deflection. The fact that resistor R8 is supplied by the unregulated input voltage VE allows another parameter to be added for acting on the duty cycle of transistor T3 as a function thereof. Diagram K of FIG. 9 illustrates the rectangular signal VP obtained at the output 14 of the modulator 10B of FIG. 8.
FIG. 10 is a schematic diagram of a conventional regulator stage 30 of the control circuit of FIG. 3. It is formed essentially by a well-known circuit called differential amplifier having two inputs, the first of which receives an adjustable fraction of the voltage to be stabilized, formed, in the present case, by the output voltage VS of the power supply device (BS, FIG. 1) and the second input of which receives a stable reference voltage which is generally generated within this stage (as in most known ballast or switched-mode voltage regulator).
The reference voltage VZ is here produced by means of a Zener diode D7 (of the BZX83C type having a stabilized Zener voltage of 7.5 V) whose cathode is connected to the input 31 receiving the output voltage VS of the device BS (FIG. 1) and whose anode is connected through an eleventh resistor R11 (10 Kohms) to ground G. The second input of the differential amplifier used here is formed by the emitter of a fifth PNP transistor T4 which is connected to the anode of the Zener diode D7. The voltage (VS-VZ) biasing this emitter is then fixed with respect to the output voltage VS. The first input of the differential amplifier is here formed by the base of transistor T4 which is biased by a voltage-divider circuit, formed from a fifteenth resistor R15 (4.7 Kohms), a potentiometer R16 (5 Kohms) and a fourteenth resistor R14 (22 Kohms) connected in series between the input terminal 31 and ground G. The base of transistor T4, connected to the slider of potentiometer R16 receives then a previously adjusted fraction of the output voltage VS supplying the horizontal deflection circuit (SH), so that it forms a constant current generator supplying a current proportional to its emitter-base voltage which is equal to the difference (error voltage) between the reference voltage VZ and the selected fraction of the output voltage VS supplied by potentiometer R16. The collector of the fourth transistor T4, connected by a tenth resistor R10 (2.2 Kohms) to the output 32, supplies then the regulating current IR to the regulating input (12, FIGS. 3 and 8) of the pulse-width modulator (10 or 10B, FIGS. 3 and 8).
It will be noted here that a feedback circuit comprising a twelfth resistor R12 (5.6 Kohms) and a seventh capacitor C7 (4.7 nF) in series connects the collector of transistor 14 to its base.
The difference between the voltage respectively provided by the potentiometer R16 and the Zener diode D7 causes more or less heavy conduction of transistor T4 which delivers the current IR.
In short, when the output voltage VS increases, the voltage (VS-VZ) at the emitter of transistor T4 increases more than that applied to its base and current IR increases. The value of I1 at which transistor T3 is cut off increases then in absolute value and this transistor T3 is turned off later, which reduces the conducting period of transistor T1. The peak current in inductance L then diminishes, which causes a reduction of the output voltage VS which comes back to its nominal value, taking into account the residual error required for controlled operation.
FIG. 11 shows the complete simplified diagram of a power supply device BS of FIG. 1 whose control circuit SCA is respectively formed by the driver circuit 20A of FIG. 4, by the modulator 10B of FIG. 8 and the regulator stage 30 of FIG. 10, except for a few variations.
The variations concern a damping resistor R17 of 1 kiloohm shunting the inductance L, resistor R8 and resistor R10 which are both connected directly to the base of transistor T3 instead of being connected to the cathode of diode D6, resistor R11 which has been omitted and a resistor R13 which shunts the slider of potentiometer R16 to ground. These details of construction have no influence at all on the operation of the circuit such as it has been described above, but simply allow easier adjustment.
Another embodiment is shown in FIG. 12. It allows more especially a television set to be supplied with power in which the horizontal deflection circuit operates from a higher DC voltage VS, of about 100 volts for example, itself obtained from an initial output voltage VSI of about 60 volts. The operation of the circuit is fundamentally the same as that of FIG. 11 and only the differences will be described below. The components playing the same role in both diagrams bear the same references. The values may however be different but their dimensioning is within the scope of a man skilled in the art. The voltage VS delivered by the power supply is used principally in the horizontal deflection circuit which is the component consuming most power in the television set. The power supply circuit components receiving permanently a voltage when the horizontal deflection circuit is not operating, but when the mains is connected, are solely those indispensable for activating the power supply, i.e. the first switching transistor T1 and the circuit for measuring the output voltage in the regulator stage 300.
To simplify the driver stage 100, instead of the single switching transistor T1, an integrated Darlington circuit T10 is used of the BU 807 type, for example. Therefore, the gain is sufficient to omit a discrete driver transistor T2 and to connect the cathode of diode D3 directly to the base input of T10. The negative -VTH pulses, coming from an intermediate tapping on coil B2 of the line output transformer, are applied directly to the base of T10 through resistor R3 which is connected in series with a diode D9 whose cathode is connected to this intermediate tapping.
Instead of the input voltage VE, the power supply input 4 of the control circuit SCB is fed by a voltage obtained by rectifying the positive half-waves (plateaux) of the -VTL voltage supplied by the first secondary winding B2, by means of a diode D8 and a capacitor C8. Thus considerably lower voltage may be obtained than that supplying the horizontal deflection circuit, of the order of 13 volts, for example. A voltage of this value allows video amplification circuits as well as other circuits of the television set to be supplied while providing for these latter a very great reliability. This voltage is applied through resistor R1 to the anodes of diodes D2 and D3 and through resistor R8 to the base of the transistor T3 of modulator 10B.

The regulator stage 300 here comprises two PNP transistors T4 and T5 connected differentially. For that, their emitters receive the voltage rectified by D8 through a resistor R18 of 1.5 kiloohms. The collector of transistor T5 is connected to ground through a resistor R20 of 3.9 kiloohms and the collector of transistor T4, which supplies the regulating current IR, is connected to the cathode of diode D6 through a resistor R10 of 4.7 kiloohms.
The reference voltage (6.2 volts) is supplied by a Zener diode D7 whose anode is connected to ground, and cathode to a resistor R19 (6.8 kiloohms) which receives the voltage rectified by D8. This reference voltage is applied to the base of transistor 14. A capacitor C9 (49 microfarads) shunts diode D7 so as to cause the reference voltage to rise gradually when the apparatus is switched on, which allows a gradual rise of the output voltage VS to be obtained.
A potentiometer R16 of 10 kiloohms connected between two stopper resistors R15 (68 kiloohms) and R14 (5.6 kiloohms) receives the voltage VS through the resistor R15 and is connected to ground through resistor R14. The sliding contact of potentiometer R16 allows a fraction of the voltage VS to be applied to the base T5. A resistor R13 (47 kiloohms) also connects this base to the common point between R15 and R16.
An anti-oscillation capacitor C10 (15 nanofarads) connects the base of the collector of transistor T5.
Thus the regulating current IR supplied by resistor R10 is directly dependent on the difference between the output voltage VS, applied to the horizontal deflection circuit, and the reference voltage determined by the Zener diode D7. The power supply BS thus stabilizes this voltage VS and at the same time the rectified voltage supplied by diode D8.
To stop this power supply, as well as that of FIG. 11 moreover, it is sufficient to stop by means of a remote control receiver, for example, the operation of the horizontal oscillator.

In this case, the input voltage VE is still present, but is considerably smaller than voltage VS. For the power supply of FIG. 12, this reduced voltage is only applied to the Darlington transistor T10 and a fraction thereof to the base of transistor T5 of the regulator stage 300. Thus the life expectation of the other components of the device BS is increased. Since the voltage supplied by diode D8 is itself regulated, it may be used for supplying a major portion of the television set, except for the horizontal deflection circuit supplied by voltage VS and the remote control receiver which must be capable of operating permanently (also in the ready state) so as to detect the turn-on control signal. The protection which was mentioned earlier on is then extended to the greatest part of the components of the television set.
It will be noted here that the three stages 10, 20 and 30 of control circuit SC (see FIGS. 1 and 3) may be formed by means of circuits different from those described and shown and which are known per se, and that it is sufficient to have a secondary winding B2 (in addition to the very-high-voltage winding) of the line transformer TL, supplying negative line-flyback pulses which may be used for generating a decreasing or increasing sawtooth voltage waveform as well as for controlling the cutting off of the first switching transistor T1.

SABA ULTRACOLOR T67R52 TELECOMMANDER CHASSIS R-110 AMBIENT LIGHT RESPONSIVE CONTROL OF BRIGHTNESS, CONTRAST AND COLOR SATURATION Gain control arrangement useful in a television signal processing system

In a color television receiver, first and second amplifiers are respectively included in the luminance and chrominance channels to permit control of contrast and saturation. The amplifiers have gain versus control voltage characteristics including linear portions extrapolated to cut off at predetermined voltages which may or may not be the same. A first potentiometer is coupled between a source of fixed voltage equal to the extrapolated cut off voltage of the first amplifier and a gain controlling voltage source. The gain controlling voltage may be produced by a circuit including an element responsive to ambient light. The wiper of the first potentiometer is coupled to the first amplifier to couple a voltage developed at a predetermined point of the first potentiometer to the first amplifier to control its gain. A second potentiometer is coupled between a source of voltage equal to the extrapolated cut off voltage of the second amplifier and the gain controlling voltage source to receive a portion of the gain controlling voltage in accordance with the ratio of the extrapolated cut off voltages of the first and second amplifiers. The wiper of the second potentiometer is coupled to the second amplifier to couple a voltage developed at a predetermined point of the second potentiometer to the second amplifier to control its gain. In this manner, the contrast of the receiver may be varied over a relatively wide range while saturation is maintained substantially constant.


1. In a color television signal processing system of the type including luminance and chrominance signal processing channels, apparatus comprising:
first and second amplifiers respectively included in said luminance and chrominance channels, said amplifiers having gain versus control voltage characteristics including linear portions extrapolated to cut-off at predetermined voltages which may or may not be the same voltage;
a gain controlling voltage source;
means for coupling said gain controlling voltage to said first amplifier to control its gain;
potentiometer means coupled between a fixed voltage substantially equal to the extrapolated cut-off voltage of said second amplifier and to said gain controlling voltage source to recieve a portion of said gain controlling voltage in accordance with the ratio of the extrapolated cut-off voltages of said first and second amplifiers; and

means for coupling a voltage developed at a predetermined point on said potentiometer means to said second amplifier to control its gain.
2. The apparatus recited in claim 1 wherein said means for coupling said gain controlling voltage to said first amplifier includes another potentiometer coupled between a source of fixed voltage substantially equal to the extrapolated cut-off voltage of said first amplifier and said gain controlling voltage source. 3. In a color television signal processing system of the type including luminance and chrominance signal processing channels, apparatus comprising:
first and second amplifiers respectively included in said luminance and chrominance channels, said amplifiers having gain control voltage characteristics including linear portions extrapolated to cut-off at substantially the same predetermined voltage;
a source of gain controlling voltage; and
means for coupling said gain controlling voltage to said first and second amplifiers.
4. Apparatus comprising:
first variable gain amplifying means for amplifying a first signal in response to a first DC control signal, said first amplifying means having a first gain versus DC control voltage characteristic including a linear region, said linear region having a gain substantially equal to 0 at a DC control voltage equal to V_O ;
second variable gain amplifying means for amplifying a second signal in response to a second DC control signal, said second amplifying means having a second gain versus DC control voltage characteristic including a linear region, said linear region having a gain substantially equal to 0 at a DC control voltage equal to AV_O, where A is a number greater than 0;
a first source of fixed voltage substantially equal to V_O ;
a second source of fixed voltage substantially equal to AV_O ;
means for developing a third DC control voltage v;
means for developing a portion Av of said third control voltage v;
first means for deriving said first control voltage including means for providing the difference between said third control voltage v and said fixed voltage V_O and means for adding a predetermined portion of the difference between said third control voltage v and said fixed voltage V_O to said DC control voltage v; and
second means for deriving said second control voltage including means for providing the difference between a portion Av of said third control voltage v and said fixed voltage AV_O and means for adding a predetermined portion of the difference between said portion Av and said fixed voltage AV_O to said DC control voltage v.

5. The apparatus recited in claim 4 wherein A is equal to 1. 6. The apparatus recited in claim 4 wherein said first amplifying means is included in a luminance channel of a televeision signal processing system and said second amplifying means is included in a chrominance channel of said television signal processing system. 7. The apparatus recited in claim 6 wherein means for developing said third control voltage includes means responsive to ambient light. 8. The apparatus recited in claim 4 wherein said first means includes first voltage divider means coupled between said fixed voltage V_O and said third DC control voltage v; and wherein said second means includes second voltage divider means coupled between said fixed voltage AV_O and said portion Av. 9. The apparatus recited in claim 8 wherein said first voltage divider means includes a first potentiometer, said first potentiometer having a wiper coupled to said first amplifying means; and wherein said second voltage divider means includes a second potentiometer, said second potentiometer having a wiper coupled to said amplifying means. 10. The apparatus recited in claim 4 wherein said second gain versus DC control voltage characteristic includes a region between said voltage AV_O and a voltage V_B where the gain is greater than 0, said voltage V_B being substantially equal to the voltage at which said second amplifying means has a gain substantially equal to 0; and wherein said second source of fixed voltage includes means for coupling said voltage V_B to said second amplifying means. 11. The apparatus recited in claim 10 wherein said second source of said voltage AV_O includes a third source of fixed voltage V_B ; potentiometer means coupled between said third source of fixed voltage V_B and said means for developing said third DC control voltage; and means coupled to said potentiometer means for developing said voltage AV_O at a point along said potentiometer means; said potentiometer means including a wiper coupled to said second amplifier means, said wiper being adjustable to couple a DC voltage V_FB and said third control voltage to said second amplifying means.

Description:

The present invention pertains to gain controlling apparatus and particularly to apparatus for controlling the gains of amplifiers included in the luminance and chrominance channels of a television signal processing system.
Recently, the maximum brightness available from television receivers has increased sufficiently so that a pleasing image may be reproduced under conditions of high ambient light as well as under conditions of low ambient light. Apparatus is known for automatically controlling the contrast and brightness properties of a television receiver in response to ambient light to provide a pleasing image over a range of ambient light conditions. Such apparatus is described in U.S. Pat. Nos. 3,027,421, entitled "Circuit Arrangements For Automatically Adjusting The Brightness And The Contrast In A Television Receiver," issued to H. Heijligers on Mar. 27, 1962 and 3,025,345, entitled "Circuit Arrangement For Automatic Readjustment Of The Background Brightness And The Contrast In A Television Receiver," issued to R. Suhrmann on Mar. 13, 1962.
Apparatus is also known for automatically controlling the contrast and saturation properties of a color television receiver by controlling the gains of luminance and chrominance channel amplifiers, respectively, in response to ambient light. Such apparatus is described in U.S. Pat. Nos. 3,813,686 entitled "Ambient Light Responsive Control Of Brightness, Contrast And Color Saturation," issued to Eugene Peter Mierzwinski, on May 28, 1974 and 3,814,852 entitled "Ambient Light Responsive Control Of Brightness, Contrast and Color Saturation," issued to Eugene P. Mierzwinski on June 4, 1974.
Also of interest is apparatus for manually controlling the gains of luminance and chrominance channel amplifiers. Such apparatus is described in U.S. Pat. Nos. 3,374,310, entitled "Color Television Receiver with Simultaneous Brightness and Color Saturation Controls," issued to G.L. Beers on Mar. 19, 1968; 3,467,770, entitled "Dual Channel Automatic Control Circuit," issued to DuMonte O. Voigt on June 7, 1966; and 3,715,463, entitled "Tracking Control Circuits Using a Common Potentiometer," issued to Lester Tucker Matzek, on Feb. 6, 1973.
When the gain of luminance channel is adjusted to control the contrast of an image, either manually or automatically, in response to ambient light, it is desirable to simultaneously control the gain of the chrominance channel in such a manner that the ratio of the gains of the luminance and chrominance channels is substantially constant over a wide range of contrast control to maintain constant saturation. If the proper ratio between the amplitudes of the chrominance and luminance signals is not maintained incorrect color reproduction may result. For instance, if the amplitude of the luminance signals are increased without correspondingly increasing the amplitude of the chrominance signals, colors may become desaturated, i.e., they will appear washed out or pastel in shade. Furthermore, it may be desirable to provide controls for presetting the gains of the luminance and chrominance channels to compensate for tolerance variations in other portions of the television signal processing apparatus.

In accordance with the present invention, apparatus is provided which may be utilized in a color television receiver to control contrast over a relatively wide range while maintaining constant saturation. The apparatus includes first and second amplifiers having gain versus control voltage characteristics including linear portions extrapolated to cut off at predetermined voltages which may or may not be the same. Means couple a gain controlling voltage source to the first amplifier to control its gain. Potentiometer means are coupled between a source of fixed voltage substantially equal to the extrapolated cut off voltage of the second amplifier and the source of gain controlling voltage to receive a portion of said gain controlling voltage in accordance with the ratio of the extrapolated cut off voltages of the amplifiers. A voltage developed at a predetermined point along the potentiometer means is coupled to the second amplifier to control its gain.
In accordance with another feature of the present invention, the means for coupling said gain controlling voltage to said first amplifier includes another potentiometer coupled between a source of fixed voltage substantially equal to the extrapolated cut off voltage of said first amplifier and said gain controlling voltage source.
In accordance with still another feature of the present invention the gain controlling voltage source includes an element responsive to ambient light .
These and other aspects of the present invention may best be understood by references to the following detailed description and accompanying drawing in which:
FIG. 1 shows the general arrangement, partly in block diagram form and partly in schematic diagram form, of a color television receiver employing an embodiment of the present invention;
FIG. 1A shows, in schematic form, a modification to the embodiment shown in FIG. 1;
FIG. 2 shows graphical representation of gain versus control voltage characteristics of amplifiers utilized in the embodiment shown in FIG. 1;
FIG. 3 shows graphical representations of gain versus control voltage characteristics of amplifiers which may be utilized in the receiver shown in FIG. 1;
FIG. 4 shows, in schematic form, another embodiment of the present invention which may be utilized to control the amplifiers whose gain versus control voltage characteristics are shown in FIG. 3;
FIG. 5 shows, in schematic form, an amplifier which may be utilized in the receiver shown in FIG. 1; and
FIG. 6 shows, in schematic form, another amplifier which may be utilized in the receiver shown in FIG. 1.
Referring now to FIG. 1, the general arrangement of a color television receiver employing the present invention includes a video signal processing unit 112 responsive to radio frequency (RF) television signals for generating, by means of suitable intermediate frequency (IF) circuits (not shown) and detection circuits (not shown), a composite video signal comprising chrominance, luminance, sound and synchronizing signals. The output of signal processing unit 112 is coupled to chrominance channel 114, luminance channel 116, a channel 118 for processing the synchronizing signals and a channel (not shown) for processing sound signals.
Chrominance processing channel 114 includes chrominance processing unit 120 which serves to remove chrominance signals from the composite video signal and otherwise process chrominance signals. Chrominance signal processing unit 120 may include, for example, automatic color control (ACC) circuits for adjusting the amplitude of the chrominance channels in response to amplitude variations of a reference signals, such as a color burst signal, included in the commposite video signal. Chrominance signal processing circuits of the type described in the U.S. Pat. No. 3,740,462, entitled "Automatic Chroma Gain Control System," issued to L.A. Harwood, on June 19, 1973 and assigned to the same assignee as the present invention are suitable for use as chrominance processing unit 120.
The output of the chrominance signal processing unit 120 is coupled to chrominance amplifier 122 which serves to amplify chrominance signals in response to a DC signal v_C generated by gain control network 142. As illustrated, chrominance amplifier 122 provides chrominance signals to a chroma demodulator 124. An amplifier suitable for use as chrominance amplifier 122 will subsequently be described with reference to FIG. 6.
Chroma demodulator 124 derives color difference signals representing, for example, R-Y, B-Y and G-Y information from the chrominance signals. Demodulator circuits of the general type illustrated by the chrominance amplifier CA 3067 integrated circuit manufactured by RCA Corporation are suitable for use as chrominance demodulator 124.
The color difference signals are applied to a video driver 126 where they are combined with the output signals -Y of luminance channel 116 to produce color signals of the appropriate polarity, representing for example, red (R), green (G) and blue (B) information. The color signals are coupled to kinescope 128.
Luminance channel 116 includes a first luminance signal processing unit 129 which relatively attenuates undesirable signals, such as chrominance or sound signals or both, present in luminance channel 116 and otherwise processes the luminance signals. The output of first luminance processing unit 129 is coupled to luminance amplifier 130 which serves to amplify the luminance signals in response to a DC control signal v_L generated by gain control unit 142 to thereby determine the contrast of a reproduced image. An amplifier suitable for use as luminance amplifier 130 will subsequently be described with reference to FIG. 5. The output of luminance amplifier 130 is coupled to second luminance signal processing unit 132 which serves to further process luminance signals. A brightness control unit 131 is coupled to luminance signal processing unit 132 to control the DC content of the luminance signals. The output -Y of luminance processing unit 132 is coupled to kinescope driver 126.

Channel 118 includes a sync separator 134 which separates horizontal and vertical synchronizing pulses from the composite video signal. The synchronizing pulses are coupled to horizontal deflection circuit 136 and vertical deflection circuit 138. Horizontal deflection circuit 136 and vertical deflection circuit 138 are coupled to kinescope 128 and to a high voltage unit 140 to control the generation and deflection of one or more electron beams generated by kinescope 128 in the conventional manner. Deflection circuits 136 and 138 also generate horizontal and vertical blanking signals which are coupled to luminance signal processing unit 132 to inhibit its operation during the horizontal and vertical retrace intervals.

Gain control unit 142 is coupled to luminance amplifier 130 and to chrominance amplifier 122 to control their gains. Gain control unit 142 includes a PNP transistor 152 arranged as an emitter-follower amplifier. The collector of transistor 152 is coupled to ground while its emitter is coupled through a series connection of a potentiometer 156 and fixed resistor 154 to a source of positive supply voltage V_O. The wiper of potentiometer 156 is coupled to luminance amplifier 130. The series connection of a potentiometer 158 and a variable resistor 159 is coupled between the source of positive supply voltage V_O and the emitter of transistor 152. The wiper of potentiometer 158 is coupled to chrominance amplifier 122.
The base of transistor 152 is coupled to the wiper of a potentiometer 146. One end of potentiometer 146 is coupled to the source of positive supply voltage V_O through a fixed resistor 144. The other end of potentionmeter 146 is coupled to ground through a light dependent resistor (LDR) 148. LDR 148 is a resistance element whose impedance varies in inverse relationship with light which impinges on it. LDR 148 may comprise a simple cadmium sulfide type of light dependent element or other suitable light dependent device. LDR 148 is desirably mounted to receive ambient light in the vicinity of the screen of kinescope 128.
A single pole double-throw switch 150 has a pole coupled to the junction of potentiometer 146 and LDR 148. A resistor 151 is coupled between the wiper of potentiometer 146 and the other pole of switch 150. The arm of switch 150 is coupled to ground.
The general arrangement shown in FIG. 1 is suitable for use in a color television receiver of the type shown, for example, in RCA Color Television Service Data 1973 No. C -8 for a CTC-68 type receiver, published by RCA Corporation, Indianapolis, Indiana.

In operation, gain control circuit 142 maintains the ratio of the gain of chrominance amplifier 122 to the gain of amplifier 130 constant in order to maintain constant saturation while providing for contrast adjustment either manually by means of potentiometer 146 or automatically by means of LDR 148. If the gain of luminance were adjusted to control the contrast of an image without a corresponding change in the gain of chrominance amplifier 122, the amplitudes of luminance signals -Y and color difference signals R-Y, B-Y and G-Y would not, in general, be in the correct ratio when combined by divider 126 to provide the desired color.
When switch 140 is in the MANUAL position, the gains of chrominance amplifier 122 and luminance amplifier 130 are controlled by adjustment of the position of potentiometer 146. When switch 150 is in the AUTO position the gain of the chrominance amplifier 122 and luminance amplifier is automatically controlled by the response of LDR 148 to ambient light conditions. The voltage developed at the wiper of potentiometer 146 (base of transistor 152) when switch 150 is in the AUTO position is inversely related to the ambient light recieved by LDR 148. It is noted that the values of resistors 114, potentiometer 146, LDR 148 and resistor 151 are desirably selected such that the adjustment of the wiper arm of potentiometer 146 when switch 150 is in the MANUAL position does not substantially affect the voltage developed at the base of transister 152 when switch 150 is placed in the AUTO position.
The control voltage v developed at the wiper arm of potentiometer 146 is coupled through emitter-follower transistor 152 to the common junction of potentiometer 156 and variable resistor 159. A control voltage v_L comprising v plus a predetermined portion of the difference V_O -v developed across the series connection of fixed resistor 154 and potentiometer 156, depending on the setting of potentiometer 156, is coupled to luminance amplifier 130 to control its gain. Similarly, a control voltage v_C comprising v plus a predetermined portion of the difference voltage V_O -v developed across the series connection of potentiometer resistor 158 and variable resistor 159, depending on the setting of the wiper of potentiometer 158, is coupled to chrominance amplifier 122 to control its gain.
The gain of luminance amplifier 130 may be pre-set to a desired value by the factory adjustment of potentiometer 156. Similarly, variable resistor 159 is provided to allow factory pre-set of the gain of the chrominance amplifier 122. Potentiometer 158 is provided to allow customer control of saturation.
Referring to FIG. 2, the gain versus voltage characteristics of chroma amplifier 122 (g_C) and luminance amplifier 130 (g_L) are shown. The characteristic g_C has a reversed S-shape including a linear portion 214. Extrapolated linear portion 214 of g_C intersects the GAIN axis at G_C and intersects the CONTROL VOLTAGE axis at V_O. Similarly, the characteristics g_L has a reverse S-shape characteristic including a linear portion 212. Extrapolated linear portion 214 of g_L intersects the GAIN axis at G_L and intersects the CONTROL VOLTAGE axis at V_O.
From FIG. 2, the expression for linear portion 212 of g_L is ##EQU1## The expression for linear portion 214 of g_C is ##EQU2## From FIG. 1, the expression for v_L is v_L = v + (V_O -v) K₁ [3]
where K₁ is determined by the voltage division of fixed resistor 154 and potentiometer 156 at the wiper of potentiometer 156. When the wiper of potentiometer 156 is at the emitter of transistor 152, K₁ =0. The expression for v_C is v_C = v + (V_O -v)K₂ [4]
where K₂ is determined by the voltage division of potentiometer 158 and fixed resistor 159 at the wiper of potentiometer 158. By combining equations [1] and [3], the equation for g_L becomes ##EQU3## By combining equations [2] and [4], the equation for g_C becomes ##EQU4## The ratio of g_L to g_C is thus ##EQU5## It is noted that this ratio is independent of DC control voltage v. Thus, although DC control voltage v may be varied either manually or in response to ambient light to control the contrast of an image reproduced by kinescope 128, the saturation remains constant.
With reference to FIG. 2, it is noted that although the linear portion 214 of g_C has an extrapolated gain equal to 0 at a control voltage equal to V_O, the non-linear portion of g_C does not attain a gain equal to 0 until a control voltage equal to V_B. That is, a control voltage of V_O will not cut-off chrominance amplifier 122.
In FIG. 1A there is shown, in schematic form, a modification to the arrangement of gain control network 142 of FIG. 1 with provisions which allow a viewer to cut off chrominance amplifier 122 to produce a more pleasing image under conditions of poor color reception due, for example, to noise or interference. The modifications to gain control unit 142 shown in FIG. 1A include coupling potentiometer resistor 158 between a source of positive supply voltage V_B, the value of V_B being greater than the value of V_O, and coupling a resistor 160 from a tap-off point 162 along potentiometer 158 to ground. The value of potentiometer 158 and resistor 160 and the location of tap 162 are selected so that voltage V_O is developed at tap 162.
The arrangement shown in FIG. 1A allows for the adjustment of contrast while constant saturation is maintained and additionally allows a viewer, by adjusting the wiper of potentiometer 158 to voltage V_B, to cut off chrominance amplifier 122.

Referring to FIG. 3 there are shown gain versus DC control voltage characteristics of chrominance and luminance amplifiers which do not have the same extrapolated linear cut off control voltage. The gain versus control voltage characteristic g_L ' of the luminance amplifier has a reverse S-shape characteristic including a linear portion 312. Extrapolated linear portion 312 of g_L ' intersects the GAIN axis at a gain G_L ' and intersects the CONTROL VOLTAGE axis at a voltage V_O '. The gain versus control voltage characteristic g_C ' of the chrominance amplifier has a reverse S-shape characteristic having a linear portion 314. Extrapolated linear portion 314 of g_C ' intersects the GAIN axis at a gain G_C ' and intersects the CONTROL VOLTAGE axis at a voltage AV_O ', where A is a number greater than zero.

From FIG. 3, the expression for linear portion 312 of g_L ' is ##EQU6## where v_L ' is the DC conrol voltage coupled to the luminance amplifier. The expression for linear portion 314 of g_C ' is ##EQU7## where v_C ' is the DC control voltage coupled to the chrominance amplifier.
A modified form of the control network 142 of FIG. 1 suitable for controlling the gain of a chrominance and a luminance amplifier having characteristics such as shown in FIG. 3 is shown in FIG. 4. Similar portions of FIGS. 1 and 4 are identified by reference numbers having the same last two significant digits and primed (') designations. The modified portions of FIG. 1 shown in FIG. 4 include the series connection resistors 460 and 462 coupled between the emitter of transistor 452 to ground. The values of resistors 460 and 462 are selected so that a portion Av' of the DC control voltage v' developed at the emitter of transistor 452 is developed at the junction of resistors 460 and 462. Furthermore, the series connection of potentiometer 458 and variable resistor 459 is coupled between the junction of resistor 460 and 462 and a source of positive supply voltage AV_O '.
From FIG. 4, the expression for control voltage v_L ' developed at the wiper of potentiometer 456 is v_L ' = v' + (v_O '-v')K₁ ' [10]
where K₁ ' is determined by the voltage division at the wiper of potentiometer 456. The expression for control voltage v_C ' developed at the wiper of potentiometer 458 is V_C ' = Av' + (AV_O ' - Av')K ₂ ' [11]
where K₂ ' is determined by the voltage division at the wiper of potentiometer 458. By combining equations [8] and [10], ##EQU8## By combining equations [9] and [11], ##EQU9## The ratio of g_L ' to g_C ' is given by the expression ##EQU10## It is noted that this ratio is independent of DC control voltage v'. Therefore, gain control network 442 of FIG. 4 also allows for the adjustment of contrast while maintaining constant saturation.
It is noted that if A were made equal to 1, the arrangement gain control unit 442 would be suitable to control the gains of chrominance and luminance amplifiers having the characteristics shown in FIG. 2.
In FIG. 5, there is shown an amplifier suitable for use as luminance amplifier 130 of FIG. 1. The amplifier includes a differential amplifier comprising NPN transistors 532 and 534. The commonly coupled emitters of transistors 532 and 534 are coupled to the collector of an NPN transistor 528. The emitter of transistor 528 is coupled via a resistor 530 to ground. The collector of transistor 532 and the collector of transistor 534, via load resistor 536, is coupled to a bias voltage provided by bias supply 546, illustrated as a series connection of batteries. The bases of transistors 532 and 534 are respectively coupled to a lower bias voltage through resistors 533 and 535 respectively.
An input signal, such as, for example, the output signal provided by first luminance processing circuit 129 of FIG. 1 is coupled to the base of transistor 532 via terminal 542. The output signal of the amplifier is developed at the collector of transistor 534 and coupled to output terminal 544.
A DC control voltage, such as v_L provided by gain control unit 142 of FIG. 1, is coupled to the base of an NPN transistor 514, arranged as an emitter-follower, via terminal 512. The collector of transistor 514 is coupled to bias supply 546. The emitter of transistor 514 is coupled to ground through the series connection of resistor 516, a diode connected transistor 518 and resistor 520.
The anode of diode 520 is coupled to the base of an NPN transistor 538. The collector of transistor 538 is coupled to the collector of transistor 534 while its emitter is coupled to ground through resistor 540. Transistor 538, resistor 540, diode 518 and resistor 520 are arranged in a current mirror configuration.
The emitter of transistor 514 is coupled to the base of a PNP transistor 522. The emitter of transistor 522 is coupled to bias supply 546 while its collector is coupled to the base of transistor 528 and to ground through the series connection of a diode connected transistor 524 and resistor 526. Transistor 528, resistor 530, diode 524 and resistor 526 are arranged in a current mirror configuration
In operation, the DC control voltage coupled to terminal 512 is coupled in inverted fashion to the anode of diode 524 by transistor 522. As a result, current directly related to the voltage developed at the anode of diode 524 flows through diode 524 and resistor 526. Due to the operation of the current mirror arrangement of diode 524, resistor 526, transistor 528 and resistor 530, a similar current flows through the emitter circuit of transistor 528. The gain of the differential amplifier comprising transistors 532 and 534 is directly related to this current flowing in the emitter circuit of transistor 528, and therefore is inversely related to the DC control voltage at terminal 512. The gain versus DC control voltage characteristics of the differential is similar to g_L shown in FIG. 2.
Further, a current is developed through the series connection of resistor 516, diode 518 and resistor 520 in direct relationship to the DC control coupled to terminal 512. A similar current is developed through resistor 540 due to the operation of the current mirror comprising diode 518, resistor 520, transistor 538 and resistor 540. This current is of the opposite sense to that provided by the current mirror arrangement of diode 524, resistor 526, transistor 528 and resistor 530 and is coupled to the collector of transistor 534 so that the DC voltage at output terminal 544 does not substantially vary with the DC control voltage.
In FIG. 6, there is shown an amplifier suitable for use as chroma amplifier 120 of FIG. 1. The amplifier shown in FIG. 6 is of the type described in U.S. patent application Ser. No. 530,405 entitled "Controllable Gain Signal Amplifier," fled by L.A. Harwood et al. on Dec. 6, 1974.
The amplifier comprises a differential amplifier including NPN transistors 624 and 625 having their bases coupled to terminal 603 via a resistor 626. Chrominance signals, provided by a source of chrominance signals such as chrominance processing unit 120 of FIG. 1, are coupled to terminal 603. The current conduction paths between the collectors and emitters of transistors 624 and 625 are respectively coupled to ground via resistors 628, 629 and 630.
A current splitter circuit comprising an NPN transistor 632 and a diode 634 is coupled to the collector of transistor 624. Diode 634 and the base-emitter junction of transistor 632 are poled in the same direction with respect to the flow of collector current in transistor 624. It desirable that conduction characteristics of transistor 632 and diode 635 be substantially matched. Similarly, the collector of transistor 625 is coupled to a second current splitter comprising a transistor 633 and a diode 635.

An output load circuit comprising series connected resistors 636 and 638 is coupled between the collector of transistor 632 and a source of operating voltage provided by bias supply 610. Amplified chrominance signals are provided at output terminal 640 for coupling, for example, to a chroma demodulator such as chroma demodulator 124 of FIG. 1. Similarly, series connected load resistors 637 and 639 are coupled between the collector of transistor 633 and bias supply 610. An output terminal 641 at the junction of resistors 637 ad 639 provides oppositely phased chrominance signals to those provided at terminal 640. The gain associated with the cascode combination of transistors 624 and 632 is controlled in response to a DC control voltage, such as, for example, v_C provided by gain control unit 142 of FIG. 1, coupled to the base of an NPN transistor 646 via terminal 602. Direct control current is supplied from the emitter of transistor 646 to diode 634 and 635 via a series resistor 652. A signal by-pass circuit comprising a series resonant combination 654 of inductance and capacitance is coupled from the anode of diode 634 to ground. Resonant circuit 654 is tuned, for example, to 3.58 MHz to provide a low impedance path to ground for color subcarrier signals.

Bias voltages and currents are supplied to the amplifier arrangement by bias supply 610, illustrated as a series connection of batterys. A voltage B+ is coupled to the collector of transistor 646. A lower bias voltage is coupled to the load circuits of transistors 632 and 633. The bases of transistors 632 and 633 are coupled in common to a still lower bias voltage. The bases of transistors 624 and 625 are coupled to a still lower bias voltage via substantially equal in value resistors 658 and 659. A resistor 694 is coupled from the common junction of resistors 658 and 659 to ground.
In operation, a quiescent operating current is provided through resistor 630. In the absence of an input signal at terminal 603, this current will divide substantially equally between the similarly biased transistors 624 and 625. If the DC control voltage at terminal 602 is near ground potential, transistor 646 will be effectively cut off and no current will flow in resistor 652 and diodes 634 and 635. In that case, neglecting the normally small difference betweeen collector and emitter currents of NPN transistors, the collector currents of transistors 624 and 625 will flow, respectively, in transistors 632 and 633. The transistors 632 and 633 are operated in common base mode and form cascode signal amplifiers with respective transistors 624 and 625. With the DC control voltage near ground potential, one-half of the quiescent current from resistor 630 flows in each of the load circuits and maximum gain for chrominance signals supplied from terminal 603 is provided.
Transistor 646 will conduct when the DC control voltage approaches the bias voltage supplied to the bases of transistors 632 and 633 of the current splitters. By selection of the circuit parameters, diodes 634 and 635 may be arranged to operate in a range between cut off to the conduction of all of the quiescent operating current supplied via resistor 630, thereby cutting off transistors 632 and 633 to provide no output signals at terminals 640 and 641.
At a DC control voltage intermediate to that corresponding to cut off of transistors 632 and 633 on the one hand and cut off of diodes 634 and 635 on the other hand, the voltage gain of the illustrated amplifier will vary in a substantially linear manner with the DC control voltage.
It is noted that although the characteristics shown in FIGS. 2 and 3 were reversed S-shaped characteristics, the characteristics could have other shapes including linear portions. For example, the characteristics could be substantially linear. Furthermore, with reference to FIG. 3, although g_C ' was shown as having a linear portion that had a cut off control voltage lower than the cut off control voltage of the linear portion of g_L ', the cut off control voltage of the linear portion of g_C ' could be greater than the cut off voltage for the linear region of g_L '. In addition, the gain control units and associate amplifiers could be arranged to utilize voltages opposite in polarity to those shown. These and other modifications are intended to be within the scope of the invention.

DECODER- MODUL:7807030500 WITH SAA1253 (ITT)

NOTBEDIEN- MODUL:7825032100

SPEICHER STEUER- MODUL 3 III:7830030800 WITH SAA1121 + SAA1220 X 2 (ITT) + LM1019 (NATIONAL)


EINBLENDUNG-MODUL:7825030400

SABA ULTRACOLOR T67R52 TELECOMMANDER CHASSIS R-110 Receiver tuning circuit with automatic search and AFC using common capacitor:
Signal-seeking tuning systems are well known for their convenience and ease of operation, especially in the field of radio and television receivers. They are commonly used to provide automatic tuning to the next higher or lower frequency of interest in response to a user-operated initiating mechanism (typically a momentary-contact switch). The advent of solid-state, voltage-dependent variable-reactance devices has permitted substantial improvement in signal-seeking tuning systems because of the consequent elimination of electric motors and other moving parts, thereby increasing efficiency and decreasing the number of malfunctions resulting from mechanical wear, dirt accumulation, and contact corrosion.

The most common type of voltage-dependent variable-reactance device is a diode which has an interelectrode capacitance directly proportional to its reverse-bias voltage, commonly referred to as a "Varicap" or "varactor" diode. By placing one or more such diodes in the frequency-selecting portion of a tuner, station selection may be achieved by progressively increasing or decreasing the voltage applied to the diode(s) until the desired frequency is obtained. Moreover, by combining a varactor-diode tuner with a progressively variable DC control voltage generator, a signal detector, and a feedback control loop, a satisfactory solid-state signal-seeking system may be created.

In conventional signal-seeking systems employing varactor diodes, however, a temporary loss of signal resulting from "airplane flutter," transmitter failure, etc., or even receiver deenergization, varies (or eliminates) the control voltage and/or interrupts the recognition signal from the signal detector and therefore sends the system seeking for a new station. The addition of complex delay circuitry for temporarily maintaining the DC control voltage not only adds appreciable cost to the system but also does not compensate for the loss of control voltage due to receiver deenergization such as when the receiver is turned off for a while.

It is therefore an object of the invention to provide a new and improved signal-seeking system for a voltage-controlled tuner.

It is a more specific object of the invention to provide such a new and improved signal-seeking tuning system which is immune to undesired signal-seeking resulting from a temporary loss of signal or receiver deenergization.

A station finder which switches to automatic frequency control during automatic finding in case of reception of a transmitter and, if desired, continues to find a transmitter some time later with the frequency control switched off.
1. A receiver tuning circuit for a tuner comprising means for detecting the presence of a received signal having an input means for coupling to said tuner; a search tuning circuit having a capacitor means for a tuning voltage for said tuner, and an automatic frequency control circuit coupled to said capacitor, said tuning circuit and said automatic frequency control circuit charging said capacitor when activated; an operating device means coupled to said detecting means and said search tuning circuit for activation of said search tuning circuit and for subsequent deactivation of said search tuning circuit and activation of said automatic frequency control circuit upon detection of a received signal; and time constant circuit means coupled between said detecting means and said operating device means for repeatedly activating said search tuning circuit and deactivating said automatic frequency control circuit a selected time after said search tuning circuit has been deactivated.

2. A receiver tuning circuit as claimed in claim 1, wherein said operating device has a supply lead and the time constant circuit is coupled to the supply lead of the operating device.

3. A receiver tuning circuit as claimed in claim 1, wherein the detection circuit is coupled to an output of a frequency detector and includes a means for preventing pulling in on the same transmitter upon activation of said search tuning circuit.

Description:

The invention relates to a receiver tuning circuit including a search tuning circuit which can be activated by a control device in which the search tuning circuit is automatically switched off when a received station is detected by a detection circuit and an automatic frequency control circuit is switched on, and in which a time constant circuit changes the state of the receiver tuning circuit after a certain time.
A receiver tuning circuit of the kind described above is known from German Offenlegungsschrift 2,023,352 which after activation of the search tuning stops the search action when a transmitter transmitting a pilot signal is received and switches on an automatic frequency control circuit. The search tuning circuit must again be activated when the received transmitter is not desired. When a transmitter without a pilot signal is received, the search tuning circuit switches over to a slowed down searching action and the automatic frequency control remains switched off. The tuning circuit includes a time constant circuit which renders the detection circuit for the pilot signal inactive some time after the finder has been activated so that the circuit can then pull in on transmitters without a pilot signal.
This known tuning circuit is only suitable for special receivers. An object of the invention is to provide a tuning circuit which is more suitable for other receiver types.
To this end a receiver tuning circuit of the kind described in the preamble according to the invention is characterized in that the time constant circuit is incorporated in the tuning circuit in such a manner that again and again it switches on the search tuning circuit a certain time after having automatically switched it off and switches off the automatic frequency control as long as the search tuning circuit is maintained operative with the aid of the operating device.
By using the step according to the invention a receiver is obtained which upon activation of the search tuning circuit receives without distortion transmitter after transmitter each during a time determined by the time constant circuit. The search tuning can be rendered inactive with the aid of the operating device after the desired station has been found. The tuning circuit is very suitable for radio or television receivers for domestic use.




SABA ULTRACOLOR T67R52 TELECOMMANDER CHASSIS R-110 Method and system for increasing the number of instructions transmitted in digital systems, I.A. in systems for remote control of television receiver:ITT VOLTAGE SYNTHESIZER TUNING SEARCH SYSTEM

Method of increasing the number of instructions according to the invention consists therein that withing the command signal (6) additional instructions are transmitted, which after being decoded in the instruction decoder (1) and processed in the strobbin signal generation circuit (4) strobes the operation of additional controlled units (5) and control the transmission of the signal through the register (2) to the controlled units (3).
In the system according to the invention, between one of the outputs od the instruction decoder (1) and the unit (3) to be controlled the register (2) is connected, provided with an additional input for the record inhibiting instruction (10), whereas to the second output of the instruction decoder (1) the strobbing signal generation circuit (4) is connected aimed at controlling the additional controlled units (5). The register (2) and the strobbing signal generation circuit (4), employed in the system according to the invention, can be built-in into each of the integrated circuits or made in form of a separate integrated circuit.

1. A method of increasing the number of instructions transmitted in remote control systems of television receivers and the like in which decoded signals directly control receiving units, comprising transmitting coded instructions in a command signal (6), decoding said instructions into a first part of an instruction signal (8), processing said first part of the instruction signal (8) in a strobing signal generation circuit (4) to provide a first signal (10) in a form for enabling the transmission of a control signal (7) through a register (2) in the form of a stored signal (11) to first receiving units (3) to be controlled while simultaneously providing a second signal (9) in a form for blocking the reception of one of said instruction signal (8) and said control signal (7) by additional receiving units (5) to be controlled, transmitting an additional coded instruction in said command signal, decoding said additional instruction into a second part of the instruction signal (8), processing said second part of the instruction signal (8) in said strobing signal generation circuit (4) to provide said first signal (10) in a form for blocking further storage of said control signal (7) in said register (2) while simultaneously providing said second signal (9) in a form for enabling the reception of said one of said instruction signal (8) and said control signal (7) by said additional receiving units (5) to be controlled, and transmitting a coded erasing instruction in said command signal for restarting the method. 2. A method according to claim 1, wherein the controlling of said additional receiving units (5) by one of said instruction signal (8) and said control signal (7) is performed while controlling said first receiving units (3) by said stored signal (11). 3. A system for increasing the number of instructions transmitted in remote control systems of television receivers and the like, comprising an instruction decoder (1), a first unit (3) to be controlled, a main register (2) connected between a first output of said instruction decoder and said first unit, an additional unit (5) to be controlled, and a strobing generation circuit (4) connected to a second output of said instruction decoder for controlling said additional unit, said additional unit having respective inputs connected to a strobing signal output of said strobing generation circuit and one of said first and second outputs of said instruction decoder. 4. A system according to claim 3, wherein said strobing generation circuit (4) has an inhibiting signal output (10) connected to an input of said main register (2) for inhibiting the storage in said main register of signals received from said first output of said instruction decoder. 5. A system according to claim 3, wherein said strobing generation circuit (4) includes an internal decoder (12), an internal register (14) and an adding gate (25), said internal decoder having outputs (13,15,16,17,18) connected to said internal register, said internal register having outputs (19-22) connected to said additional unit (5) and to said adding gate, said adding gate providing said inhibiting signal output (10) both to said main register (2) and to an inhibit input of said internal register.

Description:

This invention relates to a method and a system making it possible to increase the number of instructions transmitted in systems of remote control of television or radio receivers, and the like.
One of the known remote control systems is a system based on integrated circuits of the firm ITT. Similarly as in other systems, the instructions transmitted remotely are coded by a transmitter, for instance SAA1024, in an electric signal modulating a wave being able to propagate in the environment. In the receiver for instance SAA 1130, the coded electric signal is received and gives at its outputs the completely decoded output information signal and decoded output control signals.
In known application notes of the firm ITT the decoded output control signals control directly the receiving devices SAA1021, SAA1020. The decoder of information transmits also other decoded control signals, for instance analog adjustment signals, turning a signal on the power supply, and other signals necessary for the operation of the system. A certain part of the total number of instructions transmitted in the coded input signal constitutes a group of additional instructions for decoding by an additional instructions decoder controlled by the output signal.
The method of increasing the number of instructions transmitted in digital systems, i.a. in remote control systems of television receivers, according to the invention comprises transmitting in the control signal additional instructions which, on being decoded in an instruction decoder and after processing in a circuit for generating strobing signals, strobe the operation of additional controlled devices and control the transmission of the control signal through a register to main controlled units. In the system according to the invention two variants of operation of the system are distinguished. In the first variant an inhibiting signal coming out of the strobing signal generation circuit enables storage by the register of the real values being decoded, the output control signals, and controls with a suitable signal the main controlled units, while blocking by another suitable signal the additional controlled devices. In the second variant of the method according to the invention, after transmission of the additional instruction in the input signal, the storage inhibiting signal inhibits the register which stores the previous instruction and interruptedly controls the controlled unit, whereby simultaneously another strobing signal enables the additional controlled units to receive the controlling instruction.
In the system according to the invention the controlling of additional units is performed in the course of uninterrupted operation of controlled units.
In the system for increasing the number of instructions transmitted in digital systems, i.a. in remote control systems of television receivers, according to the invention, between one output of the instruction decoder and first controlled units a register is connected, having an additional input for a recording inhibiting signal, whereas to another output of the instruction decoder a strobing signal generation circuit is connected for controlling additional controlled units.
The inputs of the additional controlled units are connected with any outputs of the instruction decoder and with outputs of a register of the strobing circuit. The register and the strobing generation circuit, employed in the system according to the invention, can be built-in in one integrated circuit or may be made in the form of separate integrated circuits.
Referring to the aforementioned system of the firm ITT, the list of instructions thereof comprises 10 instructions used for basic servicing of the television receivers, 16 instructions for program selection and 5 additional instructions. In the method according to the invention, by using all the additional instructions, additionally 5×16 instructions are obtained. The number of all useful instructions in the method according to the invention amounts to 10+16+5×16=106 instructions, and thus by 75 instructions more than it was foreseen by the manufacturer of said systems.
Employing of the method and the system in a simple constructional arrangement enables one to multiply the number of transmitted signals, and simultaneously the number of units to be controlled. With reference to the system of the firm ITT, based on integrated circuits SAA1024, SAA1130, SAA1021, SAA1020, this enables one to employ additionally a teletext, a time programmer, an electronic watch, remote control of a radio receiver, tuning of a second head to observe another program, and other uses that were not possible and not foreseen by the manufacturer of said circuits.
The method and system according to the invention will be now described by means of an exemplary embodiment with reference to the accompanying drawing, wherein:
FIG. 1 is the block diagram of the system, and
FIG. 2 is the connection diagram of the strobing circuit.
The system of an instruction invention consists of the decoder 1, one output of which is connected through a register 2 with units 3 to be controlled. Another output of the instruction decoder 1 is connected with a strobing signal generation system 4 to the output of which is connected an additional controlled unit 5 having inputs connected with either output of the decoder 1.
The strobing circuit 4 is equipped with a decoder 12 an output 13 of which is connected with the clearing input of a register 14, and outputs 15, 16, 17, 18 of which are connected with the recording inputs of the register 14. The registers outputs 19, 20, 21, and 22, however, are connected with the additional unit 5 (FIG. 1) and with an adding gate 23, the output 10 of which is connected with the record inhibiting input of the register 14 and with the record inhibiting input of the register 2.
In the method according to the invention, the control signal 6 received by the instruction decoder 1 is decoded into groups of instructions 7 and 8. The instructions 8 after being processed in the strobing signal generating circuit 4 strobe the operation of additional devices 5 in the form of a signal 9, and in the form of the inhibiting signal 10 they control the operation of the register 2. A part of instructions 8, after processing in the strobbing circuit 4, enables with the signal 10 the transmission of the instructions 7 through the register 2 to the controlled units 3 in the form of the decoded control signal 11. Simultaneously, the decoded instruction 8 blocks with the strobing signal 9 the receiving of instructions 7 or 8 by the additional units 5 to be controlled. After transmitting the additional information from the second part of the instructions 8 in the signal 6, the instruction 8 after processing in the strobing signal generating circuit 4 blocks with the signal 10 the register 2, which stores the previous signal 7 and uninterruptedly controls the units 3 to be controlled, and simultaneously enables the additional controlled units 5 to receive instructions 7 or 8. The transmission of an erasing instruction in the signal 6 causes the return to the previous way of transmission and the turning off of the additional units 5.
The controlling of additional units 5 in the method according to the invention by means of the signal 7 or 8 is performed in the course of uninterrupted controlling of the units 3 by means of the signal 11 from the register 2.