The GALAXI MOD. GALAXONE 27" is a 27 inches color screen television with 16 programs and OSD clock time feature.
It has ultrasonic remote and a upside local keyboard TELECOM54 for tuning and clock programming.
Where such apparatus as television receivers are to be controlled from a viewer location as to channel, volume, brightness, etc., the remote control systems usually are made up of a hand held transmitter which transmits an ultrasonic signal to a receiver connected to or built within the television receiver. The depression of buttons on the transmitter causes a variety of signals or signal frequencies to be transmitted, whereby channel change, volume change, etc. is responsively obtained.
However such systems have individually suffered from one or more problems, such as inability to have direct access to the desired channel, slow access, insufficient noise immunity making it often possible to operate the system with the jingling of a key chain or an ultrasonic sound originating from a dishwasher etc., unreliable control due to the absence of means to detect and suppress transmission errors resulting from echoes, interfering signal sources, etc. Also some control systems are not suitable for continuous analog commands such as volume, brightness, etc. Existing systems also often require the need for bandpass filters and accurate crystal oscillators which make them costly. Many systems are not very suitable for integration into custom integrated circuits.
The present invention provides a remote control system whereby the nature of the remote control signal allows utmost reliability of control. The remote control receiver will be found to be virtually immune to echoes and ambient ultrasonic noises, and therefore will not produce a false response in the presence of echoes and ultrasonic interfering signals. A variety of kinds of commands can be provided, and with the preferred embodiment disclosed, up to ninety-nine channels in a television receiver can be instantaneously selected, without the requirement for sequentially stepping through each channel. Volume can be varied or muted, tint or brightness controlled, etc.
The above advantages are obtained by the transmission of a unique type of two tone coded signal which advantageously contains information defining start-up transmitted data, type of command (i.e. channel select identification or miscellaneous command such as volume), information permitting reconstruction of clock and identification of end of data. The two tones are transmitted sequentially. The second tone is transmitted to provide masking of echoes produced by the first tone and to mask noises that may be present in the operating environment of the system.
Since the two tones may be close together in frequency, it is possible to operate the remote control system in conjunction with high sensitivity resonant type microphones, thereby achieving high sensitivity together with high noise immunity. This also eliminates the need for input bandpass amplifiers.
The inventive receiver is thus rendered immune from operation by extraneous noise further by the provision of received data error checking circuitry for the timing of input pulses, etc., and for rejecting the data if an error is detected. The receiver also has provision for operation of continuous analog circuits in a television set, such as brightness, volume and tint controls, etc. Since echoes are masked out in the present system, data transmission can occur much more rapidly than in prior systems, as the receiver does not have to wait until echoes die out between transmission of bits for identification of data pulses.
Since all that is frequency dependent is the detection of signal above or below a predetermined reference frequency, accurate crystals for timing and reference frequency generation are not needed. The receiver is virtually entirely digital logic, making it suitable for monolithic integration with a minimum of external components. CMOS integrated circuit logic is preferred, minimizing power supply requirements.
In the preferred embodiment, two digits are transmitted separately and the second must be received within a given time interval, or the first number is disregarded. This method eliminates the need for a clear key as normally present on calculators.
The output of the receiver is a binary or BCD signal which can be used by known means to control the frequency of a selected channel, or to perform other functions such as variation of volume, control of brightness, tint, etc. in a television set.
It should also be understood that the use of this invention is not intended to be restricted to a television set, but can be utilized for the control of a large variety of other kinds of apparatus, e.g. door locks, household appliances, radio receivers, production machinery, etc. While the description below will be directed to a wireless ultrasonic transmitter-receiver system, it should be understood that a wired system, a radio control system, etc. could be used in the alternative.
The advantages of the invention are obtained by the provision of a system including means for receiving a transmitted signal comprising a pulse envelope modulated continuous wave ultrasonic signal at a first predetermined frequency, each pulse being immediately followed by a continuous wave ultrasonic signal at a second predetermined frequency which has amplitude such as to mask echoes of the first predetermined frequency at the receiving means, the pulses being representative of a sequence of binary bits, means to determine whether the received signal is above or below the frequency of a reference frequency, means for recognizing a change in input frequency with respect to the reference frequency, and means for counting said changes, determining the value of the binary bits, and providing a parallel coded signal representative of said value.
Featuring a OSD Clock Timer and a Channel change program on screen displayed......
This invention relates generally to a television receiver and more particularly is directed to a television receiver which can indicate the numeral of a channel after the channel is changed.There is proposed a television receiver in which when a channel is changed, the numeral indicative of the channel after the channel is changed is indicated on the screen of a cathode ray tube during a predetermined period. A conventional channel indicator used in such television receiver requires a special LSI (large scale integration) chip to indicate the numeral of the channel. However, such LSI chip requires a substantial investment in time and money from its designing to the completion, and when the designing thereof is changed midway, it is quite difficult to cope with such change.
Such equipment included clock mechanisms and specialized electronic circuits adapted for automaticturn on and of the tv set according to user presets.In general these prior art devices and apparatus employ complicated electronic circuits.
- Fully modular chassis.
The set is a first in featuring a new set of PAL decoder chips which has been introduced by Siemens, the TDA2560/TDA2522/TDA2530. The first two of these second -source the latest Philips/Mullard decoder i.c.s, with the TDA2560 as luminance and chrominance signal amplifier and the TDA2522 as the reference oscillator/chrominance demodulator. Interesting features of this set up are the fact that the burst signal passes through the chrominance delay line and the fact that the reference oscillator operates at 8.86MHz, a digital divider providing exactly 90° phase displaced 4.43MHz outputs without the need for a phase shift coil. The first UK produced chassis to use these i.c.s is the Tandberg CTV3, the larger UK setmakers staying for the time being with the TBA560C/TBA540/TCA800 combination. The third i.c. from Siemens is the TDA2530 which supersedes the well known TBA530 luminance/colour-difference signal matrix- ing i.c. The TDA2530 contains a negative feedback driver amplifier and internal clamping in addition to the matrixing network.
- Horizontal Beam Deflection and high voltage generating circuits realized with Thyristors circuits.
It's a very good system to use where the line scan coils require large
peak currents with only a moderate flyback voltage an intrinsic
characteristic of toroidally wound deflection coils. The basic thyristor
line output stage arrangement used in all these chassis is shown in
Fig. 1
it was originally devised by RCA. Many sets fitted with 110°, narrow -neck delta -gun tubes used a thyristor line output stage - for example those in the Grundig and Saba ranges and the Finlux Peacock , Indesit, Siemens, Salora, Metz, Nordmende, Blaupunkt, ITT, Seleco, REX, Mivar, Emerson, Brionvega, Loewe, Galaxi, Stern, Zanussi, Wega, Philco. The circuit continued to find favour in earlier chassis designed for use with in -line gun tubes, examples being found in the Grundig and Korting ranges - also, Indesit, Siemens, Salora, Metz, Nordmende, Blaupunkt, ITT, Seleco, REX, Mivar, Emerson, Brionvega, Loewe, Galaxi, Stern, Zanussi, Wega, Philco the Rediffusion Mk. III chassis. Deflection currents of up to 13A peak -to -peak are commonly encountered with 110° tubes, with a flyback voltage of only some 600V peak to peak. The total energy requirement is of the order of 6mJ, which is 50 per cent higher than modern 110° tubes of the 30AX and S4 variety with their saddle -wound line scan coils. The only problem with this type of circuit is the large amount of energy that shuttles back and forth at line frequency. This places a heavy stress on certain components. Circuit losses produce quite high temperatures, which are concentrated at certain points, in particular the commutating combi coil. This leads to deterioration of the soldered joints around the coil, a common cause of failure. This can hav
e
a cumulative effect, a high resistance joint increasing the local
heating until the joint becomes well and truly dry -a classic symptom
with some Grundig / Emerson sets. The wound components themselves can be
a source of trouble, due to losses - particularly the combi coil and
the regulating transductor. Later chassis are less prone to this sort of
thing, partly because of the use of later generation, higher efficiency
yokes but mainly due to more generous and better design of the wound
components. The ideal dielectric for use in the tuning capacitors is
polypropylene (either metalised or film). It's a truly won- derful
dielectric - very stable, with very small losses, and capable of
operation at high frequencies and elevated temperatures. It's also
nowadays reasonably inexpensive. Unfortunately many earlier chassis of
this type used polyester capacitors, and it's no surprise that they were
inclined to give up. When replacing the tuning capacitors in a
thyristor line output stage it's essential to use polypropylene types -a
good range of axial components with values ranging from 0.001µF to
047µF is available from RS Components, enabling even non-standard values
to be made up from an appropriate combination. Using polypropylene
capacitors in place of polyester ones will not only ensure capacitor
reliability but will also lower the stress on other components by
reducing the circuit losses (and hence power consumption).
Numerous circuit designs for completely transistorized television receivers either have been incorporated in commercially available receivers or have been described in detail in various technical publications. One of the most troublesome areas in such transistor receivers, from the point of View of reliability and economy, lies in the horizontal deflection circuits.
As an attempt to avoid the voltage and current limitations of transistor deflection circuits, a number of circuits have been proposed utilizing the silicon controlled rectifier (SCR), a semiconductor device capable of handling substantially higher currents and voltages than transistors.
The circuit utilizes two bi-directionally conductive switching means which serve respectively as trace and commutating switches. Particularly, each of the switching means comprises the parallel combination of a silicon controlled rectifier (SCR) and a diode. The commutating switch is triggered on shortly before the desired beginning of retrace and, in conjunction with a resonant commutating circuit having an inductor and two capacitors, serves to turn off the trace switch to initiate retrace. The commutating circuit is also arranged to turn oft the commutating SCR before the end of retrace.
like the GALAXI GALAXINO 16.
The set is build with a Modular chassis design because as modern television receivers become more complex the problem of
repairing the receiver becomes more difficult. As the number of
components used in the television receiver increases the susceptibility
to breakdown increases and it becomes more difficult to replace
defective components as they are more closely spaced. The problem has
become even more complicated with the increasing number of color
television receivers in use. A color television receiver has a larger
number of circuits of a higher degree of complexity than the black and
white receiver and further a more highly trained serviceman is required
to properly service the color television receiver.
Fortunately for the service problem to date, most failures occur in the vacuum tubes used in the television receivers. A faulty or inoperative vacuum tube is relatively easy to find and replace. However, where the television receiver malfunction is caused by the failure of other components, such as resistors, capacitors or inductors, it is harder to isolate the defective component and a higher degree of skill on the part of the serviceman is required.
Even with the great majority of the color television receiver malfunctions being of the "easy to find and repair" type proper servicing of color sets has been difficult to obtain due to the shortage of trained serviceman.
At the present time advances in the state of the semiconductor art have led to the increasing use of transistors in color television receivers. The receiver described in this application has only two tubes, the picture tube and the high voltage rectifier tube, all the other active components in the receiver being semiconductors.
One important characteristic of a semiconductor device is its extreme reliability in comparison with the vacuum tube. The number of transistor and integrated circuit failures in the television receiver will be very low in comparison with the failures of other components, the reverse of what is true in present day color television receivers. Thus most failures in future television receivers will be of the hard to service type and will require more highly qualified servicemen.
The primary symptoms of a television receiver malfunction are shown on the picture tube of the television receiver while the components causing the malfunction are located within the cabinet. Also many adjustments to the receiver require the serviceman to observe the screen. Thus the serviceman must use unsatisfactory mirror arrangements to remove the electronic chassis from the cabinet, usually a very difficult task. Further many components are "buried" in a maze of circuitry and other components so that they are difficult to remove and replace without damage to other components in the receiver.
Repairing a modern color television receiver often requires that the receiver be removed from the home and carried to a repair shop where it may remain for many weeks. This is an expensive undertaking since most receivers are bulky and heavy enough to require at least two persons to carry them. Further, two trips must be made to the home, one to pick up the receiver and one to deliver it. For these reasons, the cost of maintaining the color television receiver in operating condition often exceeds the initial cost of the receiver and is an important factor in determining whether a receiver will be purchased.
Therefore, the object of this invention is to provide a transistorized color television receiver in which the main electronic chassis is easily accessible for maintenance and adjustment. Another object of this invention is to provide a transistorized color television receiver in which the electronic circuits are divided into a plurality of modules with the modules easily removable for service and maintenance. The main electronic chassis is slidably mounted within the cabinet so that it may be withdrawn, in the same manner as a drawer, to expose the electronic circuitry therein for maintenance and adjustment from the rear closure panel after easy removal. Another aspect is the capability to be serviced at eventually the home of the owner.
GALAXI (G.E.C. Galaxi Electronic Company) WAS an Italian factory for radios and television sets site in Milan in Ciordi Street in Italy.
It was founded by the Italian Business man Carlo Alberto Tregua.
This Firm is defunct Very long time ago in the 80's.
It has ultrasonic remote and a upside local keyboard TELECOM54 for tuning and clock programming.
Where such apparatus as television receivers are to be controlled from a viewer location as to channel, volume, brightness, etc., the remote control systems usually are made up of a hand held transmitter which transmits an ultrasonic signal to a receiver connected to or built within the television receiver. The depression of buttons on the transmitter causes a variety of signals or signal frequencies to be transmitted, whereby channel change, volume change, etc. is responsively obtained.
However such systems have individually suffered from one or more problems, such as inability to have direct access to the desired channel, slow access, insufficient noise immunity making it often possible to operate the system with the jingling of a key chain or an ultrasonic sound originating from a dishwasher etc., unreliable control due to the absence of means to detect and suppress transmission errors resulting from echoes, interfering signal sources, etc. Also some control systems are not suitable for continuous analog commands such as volume, brightness, etc. Existing systems also often require the need for bandpass filters and accurate crystal oscillators which make them costly. Many systems are not very suitable for integration into custom integrated circuits.
The present invention provides a remote control system whereby the nature of the remote control signal allows utmost reliability of control. The remote control receiver will be found to be virtually immune to echoes and ambient ultrasonic noises, and therefore will not produce a false response in the presence of echoes and ultrasonic interfering signals. A variety of kinds of commands can be provided, and with the preferred embodiment disclosed, up to ninety-nine channels in a television receiver can be instantaneously selected, without the requirement for sequentially stepping through each channel. Volume can be varied or muted, tint or brightness controlled, etc.
The above advantages are obtained by the transmission of a unique type of two tone coded signal which advantageously contains information defining start-up transmitted data, type of command (i.e. channel select identification or miscellaneous command such as volume), information permitting reconstruction of clock and identification of end of data. The two tones are transmitted sequentially. The second tone is transmitted to provide masking of echoes produced by the first tone and to mask noises that may be present in the operating environment of the system.
Since the two tones may be close together in frequency, it is possible to operate the remote control system in conjunction with high sensitivity resonant type microphones, thereby achieving high sensitivity together with high noise immunity. This also eliminates the need for input bandpass amplifiers.
The inventive receiver is thus rendered immune from operation by extraneous noise further by the provision of received data error checking circuitry for the timing of input pulses, etc., and for rejecting the data if an error is detected. The receiver also has provision for operation of continuous analog circuits in a television set, such as brightness, volume and tint controls, etc. Since echoes are masked out in the present system, data transmission can occur much more rapidly than in prior systems, as the receiver does not have to wait until echoes die out between transmission of bits for identification of data pulses.
Since all that is frequency dependent is the detection of signal above or below a predetermined reference frequency, accurate crystals for timing and reference frequency generation are not needed. The receiver is virtually entirely digital logic, making it suitable for monolithic integration with a minimum of external components. CMOS integrated circuit logic is preferred, minimizing power supply requirements.
In the preferred embodiment, two digits are transmitted separately and the second must be received within a given time interval, or the first number is disregarded. This method eliminates the need for a clear key as normally present on calculators.
The output of the receiver is a binary or BCD signal which can be used by known means to control the frequency of a selected channel, or to perform other functions such as variation of volume, control of brightness, tint, etc. in a television set.
It should also be understood that the use of this invention is not intended to be restricted to a television set, but can be utilized for the control of a large variety of other kinds of apparatus, e.g. door locks, household appliances, radio receivers, production machinery, etc. While the description below will be directed to a wireless ultrasonic transmitter-receiver system, it should be understood that a wired system, a radio control system, etc. could be used in the alternative.
The advantages of the invention are obtained by the provision of a system including means for receiving a transmitted signal comprising a pulse envelope modulated continuous wave ultrasonic signal at a first predetermined frequency, each pulse being immediately followed by a continuous wave ultrasonic signal at a second predetermined frequency which has amplitude such as to mask echoes of the first predetermined frequency at the receiving means, the pulses being representative of a sequence of binary bits, means to determine whether the received signal is above or below the frequency of a reference frequency, means for recognizing a change in input frequency with respect to the reference frequency, and means for counting said changes, determining the value of the binary bits, and providing a parallel coded signal representative of said value.
Featuring a OSD Clock Timer and a Channel change program on screen displayed......
This invention relates generally to a television receiver and more particularly is directed to a television receiver which can indicate the numeral of a channel after the channel is changed.There is proposed a television receiver in which when a channel is changed, the numeral indicative of the channel after the channel is changed is indicated on the screen of a cathode ray tube during a predetermined period. A conventional channel indicator used in such television receiver requires a special LSI (large scale integration) chip to indicate the numeral of the channel. However, such LSI chip requires a substantial investment in time and money from its designing to the completion, and when the designing thereof is changed midway, it is quite difficult to cope with such change.
Such equipment included clock mechanisms and specialized electronic circuits adapted for automaticturn on and of the tv set according to user presets.In general these prior art devices and apparatus employ complicated electronic circuits.
- Fully modular chassis.
The set is a first in featuring a new set of PAL decoder chips which has been introduced by Siemens, the TDA2560/TDA2522/TDA2530. The first two of these second -source the latest Philips/Mullard decoder i.c.s, with the TDA2560 as luminance and chrominance signal amplifier and the TDA2522 as the reference oscillator/chrominance demodulator. Interesting features of this set up are the fact that the burst signal passes through the chrominance delay line and the fact that the reference oscillator operates at 8.86MHz, a digital divider providing exactly 90° phase displaced 4.43MHz outputs without the need for a phase shift coil. The first UK produced chassis to use these i.c.s is the Tandberg CTV3, the larger UK setmakers staying for the time being with the TBA560C/TBA540/TCA800 combination. The third i.c. from Siemens is the TDA2530 which supersedes the well known TBA530 luminance/colour-difference signal matrix- ing i.c. The TDA2530 contains a negative feedback driver amplifier and internal clamping in addition to the matrixing network.
- Horizontal Beam Deflection and high voltage generating circuits realized with Thyristors circuits.
The massive demand for colour television receivers in Europe/Germany
in the 70's brought about an influx of sets from the continent. Many of
these use the thin -neck (29mm) type of 110° shadowmask tube and the
Philips 20AX CRT Tube, plus the already Delta Gun CRT .
Scanning
of these tubes is accomplished by means of a toroidally wound
deflection yoke (conventional 90° and thick -neck 110° tubes operate
with
saddle -wound deflection coils). The inductance of a toroidal yoke is
very much less than that of a saddle -wound yoke, thus higher scan currents are required.
The deflection current necessary for the line scan is about 12A peak
-to -peak. This could be provided by a transistor line output stage but a
current step-up transformer, which is bulky and both difficult and
costly to manufacture, would be required.
An entirely different
approach, pioneered by RCA in America and developed by them and by ITT
(SEL) in Germany, is the thyristor line output stage. In this system the
scanning current is provided via two thyristors and two switching diodes
which due to their characteristics can supply the deflection yoke
without a step-up transformer (a small transformer is still required to
obtain the input voltage pulse for the e.h.t. tripler). The purpose of
this article is to explain the basic operation of such circuits. The
thyristor line output circuit offers high reliability since all
switching occurs at zero current level. C.R.T. flashovers, which can
produce high current surges (up to 60A), have no detrimental effects on
the switching diodes or thyristors since the forward voltage drop across
these devices is small and the duration of the current pulses short. If
a surge limiting resistor is pro- vided in the tube's final anode
circuit the peak voltages produced by flashovers seldom exceed the
normal repetitive circuit voltages by more than 50-100V. This is well
within the device ratings.
It's a very good system to use where the line scan coils require large
peak currents with only a moderate flyback voltage an intrinsic
characteristic of toroidally wound deflection coils. The basic thyristor
line output stage arrangement used in all these chassis is shown in
Fig. 1it was originally devised by RCA. Many sets fitted with 110°, narrow -neck delta -gun tubes used a thyristor line output stage - for example those in the Grundig and Saba ranges and the Finlux Peacock , Indesit, Siemens, Salora, Metz, Nordmende, Blaupunkt, ITT, Seleco, REX, Mivar, Emerson, Brionvega, Loewe, Galaxi, Stern, Zanussi, Wega, Philco. The circuit continued to find favour in earlier chassis designed for use with in -line gun tubes, examples being found in the Grundig and Korting ranges - also, Indesit, Siemens, Salora, Metz, Nordmende, Blaupunkt, ITT, Seleco, REX, Mivar, Emerson, Brionvega, Loewe, Galaxi, Stern, Zanussi, Wega, Philco the Rediffusion Mk. III chassis. Deflection currents of up to 13A peak -to -peak are commonly encountered with 110° tubes, with a flyback voltage of only some 600V peak to peak. The total energy requirement is of the order of 6mJ, which is 50 per cent higher than modern 110° tubes of the 30AX and S4 variety with their saddle -wound line scan coils. The only problem with this type of circuit is the large amount of energy that shuttles back and forth at line frequency. This places a heavy stress on certain components. Circuit losses produce quite high temperatures, which are concentrated at certain points, in particular the commutating combi coil. This leads to deterioration of the soldered joints around the coil, a common cause of failure. This can hav
e
a cumulative effect, a high resistance joint increasing the local
heating until the joint becomes well and truly dry -a classic symptom
with some Grundig / Emerson sets. The wound components themselves can be
a source of trouble, due to losses - particularly the combi coil and
the regulating transductor. Later chassis are less prone to this sort of
thing, partly because of the use of later generation, higher efficiency
yokes but mainly due to more generous and better design of the wound
components. The ideal dielectric for use in the tuning capacitors is
polypropylene (either metalised or film). It's a truly won- derful
dielectric - very stable, with very small losses, and capable of
operation at high frequencies and elevated temperatures. It's also
nowadays reasonably inexpensive. Unfortunately many earlier chassis of
this type used polyester capacitors, and it's no surprise that they were
inclined to give up. When replacing the tuning capacitors in a
thyristor line output stage it's essential to use polypropylene types -a
good range of axial components with values ranging from 0.001µF to
047µF is available from RS Components, enabling even non-standard values
to be made up from an appropriate combination. Using polypropylene
capacitors in place of polyester ones will not only ensure capacitor
reliability but will also lower the stress on other components by
reducing the circuit losses (and hence power consumption).Numerous circuit designs for completely transistorized television receivers either have been incorporated in commercially available receivers or have been described in detail in various technical publications. One of the most troublesome areas in such transistor receivers, from the point of View of reliability and economy, lies in the horizontal deflection circuits.
As an attempt to avoid the voltage and current limitations of transistor deflection circuits, a number of circuits have been proposed utilizing the silicon controlled rectifier (SCR), a semiconductor device capable of handling substantially higher currents and voltages than transistors.
The circuit utilizes two bi-directionally conductive switching means which serve respectively as trace and commutating switches. Particularly, each of the switching means comprises the parallel combination of a silicon controlled rectifier (SCR) and a diode. The commutating switch is triggered on shortly before the desired beginning of retrace and, in conjunction with a resonant commutating circuit having an inductor and two capacitors, serves to turn off the trace switch to initiate retrace. The commutating circuit is also arranged to turn oft the commutating SCR before the end of retrace.
It's quite uncommon design was remarkable in that era of time even with smaller modelsThe new colour picture tube introduced in the UK by Thorn and developed in the US by RCA has an abundance of novel features designed to make it easier to operate and perhaps cheaper to produce. It arrives in an aura of snappy abbreviations such as PST ("precision static toroid") and ITC ("integral tube components") but the proud inventors for some reason insist on giving its full name, Precision In - Line System, the full treatment on each appearance. It seems inevitable that others will have no such inhibitions, so we shall draw comparisons between the new PI tube, the standard shadowmask tube and the Sony Trinitron. These are the only colour large scale production at present. Over twenty years have passed since RCA introduced the shadowmask cathode-ray tube, the first colour television display device to be mass produced. For most of this time it has remained the only colour picture tube available and it is now prodUced under licence to the inventors by many manufacturers all over the world. Detail improvements have been made of course but the basic scheme has remained unchanged: three electron guns in a triangular (or "delta") formation, a shadowmask etched with a pattern of tiny holes and a corresponding array of red, green and blue phosphor dots on the screen. In the last few years the Sony Trinitron has appeared and soon established itself as a display device for use in the small screen portable receivers for which it was designed. The three electron guns in this tube are closely spaced side by side in a horizontal plane. The "shadowmask" contains vertical slits instead of holes and the screen is composed of vertical phosphor stripes in a red -green- blue sequence.
like the GALAXI GALAXINO 16.
The set is build with a Modular chassis design because as modern television receivers become more complex the problem of
repairing the receiver becomes more difficult. As the number of
components used in the television receiver increases the susceptibility
to breakdown increases and it becomes more difficult to replace
defective components as they are more closely spaced. The problem has
become even more complicated with the increasing number of color
television receivers in use. A color television receiver has a larger
number of circuits of a higher degree of complexity than the black and
white receiver and further a more highly trained serviceman is required
to properly service the color television receiver. Fortunately for the service problem to date, most failures occur in the vacuum tubes used in the television receivers. A faulty or inoperative vacuum tube is relatively easy to find and replace. However, where the television receiver malfunction is caused by the failure of other components, such as resistors, capacitors or inductors, it is harder to isolate the defective component and a higher degree of skill on the part of the serviceman is required.
Even with the great majority of the color television receiver malfunctions being of the "easy to find and repair" type proper servicing of color sets has been difficult to obtain due to the shortage of trained serviceman.
At the present time advances in the state of the semiconductor art have led to the increasing use of transistors in color television receivers. The receiver described in this application has only two tubes, the picture tube and the high voltage rectifier tube, all the other active components in the receiver being semiconductors.
One important characteristic of a semiconductor device is its extreme reliability in comparison with the vacuum tube. The number of transistor and integrated circuit failures in the television receiver will be very low in comparison with the failures of other components, the reverse of what is true in present day color television receivers. Thus most failures in future television receivers will be of the hard to service type and will require more highly qualified servicemen.
The primary symptoms of a television receiver malfunction are shown on the picture tube of the television receiver while the components causing the malfunction are located within the cabinet. Also many adjustments to the receiver require the serviceman to observe the screen. Thus the serviceman must use unsatisfactory mirror arrangements to remove the electronic chassis from the cabinet, usually a very difficult task. Further many components are "buried" in a maze of circuitry and other components so that they are difficult to remove and replace without damage to other components in the receiver.
Repairing a modern color television receiver often requires that the receiver be removed from the home and carried to a repair shop where it may remain for many weeks. This is an expensive undertaking since most receivers are bulky and heavy enough to require at least two persons to carry them. Further, two trips must be made to the home, one to pick up the receiver and one to deliver it. For these reasons, the cost of maintaining the color television receiver in operating condition often exceeds the initial cost of the receiver and is an important factor in determining whether a receiver will be purchased.
Therefore, the object of this invention is to provide a transistorized color television receiver in which the main electronic chassis is easily accessible for maintenance and adjustment. Another object of this invention is to provide a transistorized color television receiver in which the electronic circuits are divided into a plurality of modules with the modules easily removable for service and maintenance. The main electronic chassis is slidably mounted within the cabinet so that it may be withdrawn, in the same manner as a drawer, to expose the electronic circuitry therein for maintenance and adjustment from the rear closure panel after easy removal. Another aspect is the capability to be serviced at eventually the home of the owner.
It was founded by the Italian Business man Carlo Alberto Tregua.
This Firm is defunct Very long time ago in the 80's.
No comments:
Post a Comment
The most important thing to remember about the Comment Rules is this:
The determination of whether any comment is in compliance is at the sole discretion of this blog’s owner.
Comments on this blog may be blocked or deleted at any time.
Fair people are getting fair reply. Spam and useless crap and filthy comments / scrapers / observations goes all directly to My Private HELL without even appearing in public !!!
The fact that a comment is permitted in no way constitutes an endorsement of any view expressed, fact alleged, or link provided in that comment by the administrator of this site.
This means that there may be a delay between the submission and the eventual appearance of your comment.
Requiring blog comments to obey well-defined rules does not infringe on the free speech of commenters.
Resisting the tide of post-modernity may be difficult, but I will attempt it anyway.
Your choice.........Live or DIE.
That indeed is where your liberty lies.
Note: Only a member of this blog may post a comment.