The NORDMENDE PRESTIGE SK2 COLOR TP8796 is a 26 inches (66cm) color television whith white wooden cabinet and 16 programs with ultrasonic remote and VST (ITT) search system.
Where such apparatus as television receivers are to be controlled from a viewer location as to channel, volume, brightness, etc., the remote control systems usually are made up of a hand held transmitter which transmits an ultrasonic signal to a receiver connected to or built within the television receiver. The depression of buttons on the transmitter causes a variety of signals or signal frequencies to be transmitted, whereby channel change, volume change, etc. is responsively obtained.
However such systems have individually suffered from one or more problems, such as inability to have direct access to the desired channel, slow access, insufficient noise immunity making it often possible to operate the system with the jingling of a key chain or an ultrasonic sound originating from a dishwasher etc., unreliable control due to the absence of means to detect and suppress transmission errors resulting from echoes, interfering signal sources, etc. Also some control systems are not suitable for continuous analog commands such as volume, brightness, etc. Existing systems also often require the need for bandpass filters and accurate crystal oscillators which make them costly. Many systems are not very suitable for integration into custom integrated circuits.
The present invention provides a remote
control system whereby the nature of the remote control signal allows
utmost reliability of control. The remote control receiver will be found
to be virtually immune to echoes and ambient ultrasonic noises, and
therefore will not produce a false response in the presence of echoes
and ultrasonic interfering signals. A variety of kinds of commands can
be provided, and with the preferred embodiment disclosed, up to
ninety-nine channels in a television receiver can be instantaneously
selected, without the requirement for sequentially stepping through each
channel. Volume can be varied or muted, tint or brightness controlled,
etc. The above advantages are obtained by the transmission of a unique type of two tone coded signal which advantageously contains information defining start-up transmitted data, type of command (i.e. channel select identification or miscellaneous command such as volume), information permitting reconstruction of clock and identification of end of data. The two tones are transmitted sequentially. The second tone is transmitted to provide masking of echoes produced by the first tone and to mask noises that may be present in the operating environment of the system.
Since the two tones may be close together in frequency, it is possible to operate the remote control system in conjunction with high sensitivity resonant type microphones, thereby achieving high sensitivity together with high noise immunity. This also eliminates the need for input bandpass amplifiers.
The inventive receiver is thus rendered immune from operation by extraneous noise further by the provision of received data error checking circuitry for the timing of input pulses, etc., and for rejecting the data if an error is detected. The receiver also has provision for operation of continuous analog circuits in a television set, such as brightness, volume and tint controls, etc. Since echoes are masked out in the present system, data transmission can occur much more rapidly than in prior systems, as the receiver does not have to wait until echoes die out between transmission of bits for identification of data pulses.
Since all that is frequency dependent is the detection of signal above or below a predetermined reference frequency, accurate crystals for timing and reference frequency generation are not needed. The receiver is virtually entirely digital logic, making it suitable for monolithic integration with a minimum of external components. CMOS integrated circuit logic is preferred, minimizing power supply requirements.
In the preferred embodiment, two digits are transmitted separately and the second must be received within a given time interval, or the first number is disregarded. This method eliminates the need for a clear key as normally present on calculators.
The output of the receiver is a binary or BCD signal which can be used by known means to control the frequency of a selected channel, or to perform other functions such as variation of volume, control of brightness, tint, etc. in a television set.
It should also be understood that the use of this invention is not intended to be restricted to a television set, but can be utilized for the control of a large variety of other kinds of apparatus, e.g. door locks, household appliances, radio receivers, production machinery, etc. While the description below will be directed to a wireless ultrasonic transmitter-receiver system, it should be understood that a wired system, a radio control system, etc. could be used in the alternative.
The advantages of the invention are obtained by the provision of a system including means for receiving a transmitted signal comprising a pulse envelope modulated continuous wave ultrasonic signal at a first predetermined frequency, each pulse being immediately followed by a continuous wave ultrasonic signal at a second predetermined frequency which has amplitude such as to mask echoes of the first predetermined frequency at the receiving means, the pulses being representative of a sequence of binary bits, means to determine whether the received signal is above or below the frequency of a reference frequency, means for recognizing a change in input frequency with respect to the reference frequency, and means for counting said changes, determining the value of the binary bits, and providing a parallel coded signal representative of said value.
The set was a luxuss model and was introducing the featuring of the PHILIPS 20AX SYSTEM CRT TUBE.The PHILIPS 20AX system was introduced in Europe as the first self converging picture tube/deflection coil, combination for 110° degree deflection and screen sizes up to 26". The system is based on the automatic convergence principle discovered by Haantjes and Lubben of Philips Research Laboratory more than 20 years ago. It makes use of an in-line gun array in conjunction with a specially designed saddle type deflection coil. Residual small tolerance errors are compensated by a simple dynamic four-pole system. The tube is 2 cm shorter than conventional 110° Degree tubes and has a standard 36.5 mm neck in order to obtain good color selection. A slotted mask is used in combination with a stripe-structure screen. Picture sharpness is ensured by an astigmatic electron gun.
The Horizontal Beam Deflection and high voltage generating circuits are realized with Thyristors circuits.
The massive demand for colour television receivers in Europe/Germany
in the 70's brought about an influx of sets from the continent. Many of
these use the thin -neck (29mm) type of 110° shadowmask tube and the
Philips 20AX CRT Tube, plus the already Delta Gun CRT .
Scanning
of these tubes is accomplished by means of a toroidally wound
deflection yoke (conventional 90° and thick -neck 110° tubes operate
with
saddle -wound deflection coils). The inductance of a toroidal yoke is
very much less than that of a saddle -wound yoke, thus higher scan currents are required.
The deflection current necessary for the line scan is about 12A peak
-to -peak. This could be provided by a transistor line output stage but a
current step-up transformer, which is bulky and both difficult and
costly to manufacture, would be required.
An entirely different
approach, pioneered by RCA in America and developed by them and by ITT
(SEL) in Germany, is the thyristor line output stage. In this system the
scanning current is provided via two thyristors and two switching diodes
which due to their characteristics can supply the deflection yoke
without a step-up transformer (a small transformer is still required to
obtain the input voltage pulse for the e.h.t. tripler). The purpose of
this article is to explain the basic operation of such circuits. The
thyristor line output circuit offers high reliability since all
switching occurs at zero current level. C.R.T. flashovers, which can
produce high current surges (up to 60A), have no detrimental effects on
the switching diodes or thyristors since the forward voltage drop across
these devices is small and the duration of the current pulses short. If
a surge limiting resistor is pro- vided in the tube's final anode
circuit the peak voltages produced by flashovers seldom exceed the
normal repetitive circuit voltages by more than 50-100V. This is well
within the device ratings. Numerous circuit designs for completely transistorized television
receivers either have been incorporated in commercially available
receivers or have been described in detail in various technical
publications. One of the most troublesome areas in such transistor
receivers, from the point of View of reliability and economy, lies in
the horizontal deflection circuits.As an attempt to avoid the voltage and current limitations of transistor deflection circuits, a number of circuits have been proposed utilizing the silicon controlled rectifier (SCR), a semiconductor device capable of handling substantially higher currents and voltages than transistors.
The circuit utilizes two bi-directionally conductive switching means which serve respectively as trace and commutating switches. Particularly, each of the switching means comprises the parallel combination of a silicon controlled rectifier (SCR) and a diode. The commutating switch is triggered on shortly before the desired beginning of retrace and, in conjunction with a resonant commutating circuit having an inductor and two capacitors, serves to turn off the trace switch to initiate retrace. The commutating circuit is also arranged to turn oft the commutating SCR before the end of retrace.
The set is build with a Modular chassis design because as modern television receivers become more complex the problem of
repairing the receiver becomes more difficult. As the number of
components used in the television receiver increases the susceptibility
to breakdown increases and it becomes more difficult to replace
defective components as they are more closely spaced. The problem has
become even more complicated with the increasing number of color
television receivers in use. A color television receiver has a larger
number of circuits of a higher degree of complexity than the black and
white receiver and further a more highly trained serviceman is required
to properly service the color television receiver. Fortunately for the service problem to date, most failures occur in the vacuum tubes used in the television receivers. A faulty or inoperative vacuum tube is relatively easy to find and replace. However, where the television receiver malfunction is caused by the failure of other components, such as resistors, capacitors or inductors, it is harder to isolate the defective component and a higher degree of skill on the part of the serviceman is required.
Even with the great majority of the color television receiver malfunctions being of the "easy to find and repair" type proper servicing of color sets has been difficult to obtain due to the shortage of trained serviceman.
At the present time advances in the state of the semiconductor art have led to the increasing use of transistors in color television receivers. The receiver described in this application has only two tubes, the picture tube and the high voltage rectifier tube, all the other active components in the receiver being semiconductors.
One important characteristic of a semiconductor device is its extreme reliability in comparison with the vacuum tube. The number of transistor and integrated circuit failures in the television receiver will be very low in comparison with the failures of other components, the reverse of what is true in present day color television receivers. Thus most failures in future television receivers will be of the hard to service type and will require more highly qualified servicemen.
The primary symptoms of a television receiver malfunction are shown on the picture tube of the television receiver while the components causing the malfunction are located within the cabinet. Also many adjustments to the receiver require the serviceman to observe the screen. Thus the serviceman must use unsatisfactory mirror arrangements to remove the electronic chassis from the cabinet, usually a very difficult task. Further many components are "buried" in a maze of circuitry and other components so that they are difficult to remove and replace without damage to other components in the receiver.
Repairing a modern color television receiver often requires that the receiver be removed from the home and carried to a repair shop where it may remain for many weeks. This is an expensive undertaking since most receivers are bulky and heavy enough to require at least two persons to carry them. Further, two trips must be made to the home, one to pick up the receiver and one to deliver it. For these reasons, the cost of maintaining the color television receiver in operating condition often exceeds the initial cost of the receiver and is an important factor in determining whether a receiver will be purchased.
Therefore, the object of this invention is to provide a transistorized color television receiver in which the main electronic chassis is easily accessible for maintenance and adjustment. Another object of this invention is to provide a transistorized color television receiver in which the electronic circuits are divided into a plurality of modules with the modules easily removable for service and maintenance. The main electronic chassis is slidably mounted within the cabinet so that it may be withdrawn, in the same manner as a drawer, to expose the electronic circuitry therein for maintenance and adjustment from the rear closure panel after easy removal. Another aspect is the capability to be serviced at eventually the home of the owner.
It has eveb a power switch child lock. A power supply control apparatus for a television receiver is useful in preventing a child from watching a television for excessive lengths of time. There has been already proposed such an apparatus in which a key is used to mechanically lock the power switch of the television receiver. The power switch locking device of the invention cooperates with a function switch or key specified in the electrical appliance to control the on/off function of the power switch.
This here shown is a heavy used set for almost 25 Years by the original owner combined with all day permanent power on.
(To see the Internal Chassis Just click on Older Post Button on bottom page, that's simple !)
Nordmende was a manufacturer of entertainment electronics based in Bremen, Germany..........................1967-1977 10 YEARS of color engineering, industrial, administrative and political factors all became hopelessly intertwined in the long but eventually unsuccessful attempt to establish a single colour - encoding system for Europe. From 1962-67 the struggle oscillated wildly between the three main systems - the American NTSC, the French SEC AM and the German PAL. There were also many variations within the SECAM and PAL systems, plus some outsiders such as NIIR, FAM, TSC, SEQUIN, LEP, and counter ideas such as the Post Office's pilot -tone reference system for NTSC, suggested by Dr N. W. J. Lewis in 1964. In February 1965 the official European delegation went to the CCIR Study Group XI meetings at Vienna firmly committed to support NTSC - yet before the end of that year it had swung over equally firmly to support PAL. Indeed for much of 1964 and 1965 the only public support in the Europeans for either PAL or SECAM came from a few technical journalists and the small engineering team at ABC, Teddington. At that period the British industry, through BREMA, was solidly behind NTSC. The BBC's then Director of Engineering, Sir Francis McLean, wrote in March 1965 that "the NTSC system is much to be preferred". The PMG made a statement in the House of Commons on February 3, 1965 in favour of NTSC. Yet today almost everyone in British broadcasting circles sincerely believes that the European made the right choice in opting for PAL. Even in the United States, the birthplace of NTSC, one finds a belief that European television benefits from having chosen PAL or SECAM, though clearly many of the original problems in handling and, particularly, in tape recording NTSC have now been largely overcome. Why did it take skilled engineers and administrators so long to come to what, with hindsight, may seem the obvious choice? And why we were still left with all three systems in general use?
The original company, Radio H. Mende & Co, was founded in 1923 by Otto Hermann Mende
(1885-1940) in Dresden. Following the destruction of the plant during the bombing raids in 1945, Martin Mende (the founder's son) created a new company in Bremen in 1947, in a former Focke-Wulf plant, under the name North German Mende Broadcast GmbH.
The name was subsequently changed to Nordmende: subsequently the
company became one of the prominent German manufacturers of radios,
televisions, tape recorders and record players in the 1950s and 1960s.
In
the 1970s, Nordmende televisions were renowned for their innovative
chassis, and for the rigorous testing and quality control of their
finished products. Both created high costs, however, which soon proved a
competitive disadvantage when the price of colour televisions began to plunge.
In 1969, Mende's sons took over the company, and in 1977 a majority shareholding was sold to the French Thomson Brandt company and the chassis remains the original NordMende until CHASSIS F9. The
following year, the family sold their remaining shares to Thomson.
In the 1980s, the factories in Bremen were closed, Nordmende becoming
purely a Thomson trademark (Starting from chassis F10 F11 they're all THOMSON).
In the 1990s, the name Nordmende was used with decreasing frequency, and it eventually disappeared in favour of the Thomson name. In 2005 Videocon Group acquired all cathode ray tube activities from Thomson. This led to the creation of VDC Technologies, which manufactures TV sets using the Nordmende brand under licence from Thomson.
The Nordmende brand name was relaunched in Ireland in September 2008 by the KAL Group. Although
Nordmende
was well known for its televisions throughout Ireland during the
1970s and 1980s, the company bought the rights to the name and
launched a range of white goods including fridges, freezers, washing machines, and dishwashers, alongside a revamped range of flat-screen TVs and stereos.
NORDMENDE HISTORY IN GERMAN:
Die Vorkriegsgeschichte findet sich unter Mende. Nach dem T
otalverlust in
Dresden gründet Martin Mende (30.12.1898-1982) unter Mitwirkung von
Hermann Weber am 26. August 1947 [FT5901] in Bremen-Hemelingen die
Norddeutsche Mende-Rundfunk GmbH.Die ersten Gehäuse liefert ein Tischler in Achim gegen Kompensation von fünf Gehäusen zu einem Rundfunkgerät. Der frühere Mende-Konstrukteur, Obering. Heer zeichnet wieder für die Geräte verantwortlich [FT49??].
Ab 27. Juli 1948 liefert die neue, zuerst 18 und bald 60 Personen umfassende Firma auf Grund von Währungsreform, Krediten und Zulieferverträgen die neue Radioproduktion.
Das Regime in Ostdeutschland lässt den Namen Mende nicht zu, so dass Martin Mende mit grafischen Konstruktionen im Zusammenhang mit «Nord» an seinen Vorkriegserfolg anschliesst.
Die Hallen der ehemaligen Focke-Wulf AG beim Bahnhof Seebaldsbrück dienen als Werkstätten. 1950 beschäftigt das Unternehmen 700, 1959 schon 3500 und im Zenit 6300 Personen.
1950 beginnt die Firma mit UKW-, 1953 mit Fernseh- und 1954 mit Mess- und Prüfgeräten. Gegen Ende der 50er Jahre heisst die Firma Norddeutsche Mende Rundfunk KG [RP7901].
Nachdem sich Nordmende bislang nicht mit Magnettongeräten befasst hat, bringt das Werk 1958 das erste deutsche Heim-Tonbandgerät mit drei Motoren auf den Markt. Allerdings dominieren auf diesem Sektor eindeutig andere Firmen wie AEG/Telefunken und Grundig. Von Nordmende kommen jeweils nur ein bis zwei Geräte (1960 keines) in die Kataloge. Dafür hat die Firma Erfolg mit einem anderen Neueinstieg:
1958 stellt Nordmende mit «Mambo» ihr erstes Reisegerät vor - aber nicht «das erste deutsche, serienmässig hergestellte und volltransistorisierte Koffergerät», wie man aus einer Quelle nachlesen kann. Danach wird Nordmende in Deutschland auf dem Sektor Reisegeräte besonders stark, obwohl sie keine Röhren-Koffer baute. Immerhin kosten die in «Mambo» verwendeten 8 Halbleiter dann im Einzelhandel DM 98.70, während für die vier D-Röhren der 90er-Serie - auch zum Katalogpreis - etwa DM 35.- auszugeben wären. Preis des ganzen Gerätes: DM 189.- plus zwei Flachbatterien von 4,5 V.
Bis 1969 gibt es ca. 92 Modelle der tragbaren Radios (Koffer- bzw. «Handradios», d.h. «Hand held radios»). Beispielsweise finden sich im Katalog 1961/62 [448] je 11 Tischradios und Radiomöbel sowie 8 Modelle von Reiseradios. 17 verschiedene Fernsehmodelle zeigen dagegen, wo in jener Zeit der Erfolg zu holen war.
Gemäss [FT7901] liegt Nordmende während kurzer Zeit mit der sogenannten «Tippomatik-Bedienung» sogar technisch vorne. Siehe auch Philips etc.
Auch Konzertschränke scheinen Ende der 50er bis Anfang 60er Jahre eine tragende Säule für Nordmende zu sein. Dabei verwendet die Firma immer wieder gleiche Namen wie «Cabinet», «Caruso», «Casino», «Cosima» sowie «Arabella» und «Isobella» mit wechselnden Zusatz-Nummern oder den Zusatz «Stereo», z.B. in den Jahren 1959 und 1960/61.
Im März 1967 nimmt das Werk die Produktion von Farbfernsehgeräten auf. Zum Firmenjubiläum erscheint eine Gerätereihe mit der Bezeichnung 'Goldene 20'. 1969 übernehmen die Mende-Söhne Karl und Hermann die Geschäftsführung.
1977 führt der verschärfte Wettbewerb zum Verkauf der Mehrheit an den französischen Konzern Thomson-Brandt; die Familie Mende zieht sich anschliessend ganz aus dem Unternehmen zurück. Martin Mende stirbt 1982.
Weblinks:
Commons: Nordmende – Sammlung von Bildern, Videos und Audiodateien
Tote Marke NORDMENDE – Verblasster Stolz. Artikel im Manager-Magazin
Ein neues Programm. Artikel in der Zeit
Fernseher: Inder produzieren neue Nordmende. Artikel bei itespresso.de
Videocon produziert Plasmaschirme für Nordmende. Artikel im pressetext.de
Einzelnachweise
Spectra Color Studio und Spectra SK2 Color de Luxe Studio auf radiomuseum.orgMarke Nordmende mit Digital- und Internetradios zurück, teltarif.de, Artikel vom 2. September 2017.
Company profile. Phillar, archiviert vom Original am 6. März 2008; abgerufen am 26. April 2013 (englisch).
Broschüre – Sprachmanager24. Abgerufen am 5. Januar 2015.
No comments:
Post a Comment
The most important thing to remember about the Comment Rules is this:
The determination of whether any comment is in compliance is at the sole discretion of this blog’s owner.
Comments on this blog may be blocked or deleted at any time.
Fair people are getting fair reply. Spam and useless crap and filthy comments / scrapers / observations goes all directly to My Private HELL without even appearing in public !!!
The fact that a comment is permitted in no way constitutes an endorsement of any view expressed, fact alleged, or link provided in that comment by the administrator of this site.
This means that there may be a delay between the submission and the eventual appearance of your comment.
Requiring blog comments to obey well-defined rules does not infringe on the free speech of commenters.
Resisting the tide of post-modernity may be difficult, but I will attempt it anyway.
Your choice.........Live or DIE.
That indeed is where your liberty lies.
Note: Only a member of this blog may post a comment.